EverFocus ECMD200 Handleiding

EverFocus Bewakingscamera ECMD200

Lees hieronder de 📖 handleiding in het Nederlandse voor EverFocus ECMD200 (10 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10

Covert Color Camera in

Working PIR Motion Detector Case

Operation Instructions

Model No. ECMD200

Please read this manual first for correct installation and operation. This manual should be retained for future

reference. The information in this manual was current when published. The manufacturer reserves the right

to revise and improve its products. All specifications are therefore subject to change without notice.

PRECAUTIONS

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio

speakers since the electromagnetic fields generated from these devices may distort the video image or

otherwise interfere with camera operation.

2. Never disassemble the camera beyond the recommendations in this manual nor introduce

materials other than those recommended herein. Improper disassembly or introduction of

corrosive materials may result in equipment failure or other damage.

3. Try to avoid facing the camera toward the sun.

In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal

circuits, as well as creating unbalanced illumination beyond the capability of the camera to

compensate.

4. Keep the power cord away from water and other liquids and never touch the power cord with

wet hands. Touching a wet power cord with your hands or touching the power cord with wet hands

may result in electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents.

Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning

For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the

hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera

lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex

solvents, corrosive or abrasive agents for cleaning of any part of the camera.

7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.

This camera is suitable for indoor operation only. Use the camera at temperatures within

-10°C~50°C (14°F~122°F) and humidity between 20%~ 80%; this device is not rated as submersible.

The input power source is 12VDC. Be sure to connect the proper + / - polarity and voltage, as

incorrect polarity or too high a voltage will likely cause the camera to fail, and such damage is

not covered by the warranty. The use of properly fused or Class 2 power limited type supplies is

highly recommended.

8. Mounting

Use care in selecting a solid mounting surface which will support the weight of the camera plus any

wind, snow, ice or other loading, and securely attach the camera to the mounting surface using screws

and anchors which will properly support the camera. If necessary (e.g. when mounting to drop ceilings)

use a safety wire to provide additional support for the camera.

OVERVIEW

The ECMD200 is a working PIR motion detector with a hidden color camera which utilizes a

Sony 1/3” Super HAD II CCD Sensor and advanced DSP solution for excellent light

sensitivity. providing well defined color and B/W video for surveillance applications. The

PIR sensor can be connected to an alarm system, light control, recording device or other

application. The camera is concealed within the device and enables surveillance of the

monitored area without reveling the fact that the area is under camera surveillance. The two

security systems combine to give improved protection in the desired area. A stylish design

combined with low current consumption delivers an excellent combination of intrusion

detection protection, image quality, value and performance.

FEATURES

Camera:

 Color camera with SONY 1/3” Super HAD II CCD sensor

 Employs Digital Signal Processor (DSP) chip-set for high quality images

 High Resolution over 600TVL

 High sensitivity, low smear, high anti-blooming and high S/N ratio for high

performance video.

 Built-in functions: Auto Electronic Shutter (AES), Auto Gain Control (AGC), Auto

Trace White Balance (ATW) Digital Wide Dynamic Range (DWDR), 2D Noise

Reduction (2DNR).

 DC power cable and video cable and power pigtail provided

 Built-in anti-aliasing function to improve perceived video image quality

PIR Motion Detector:

 PIR motion sensor for intrusion protection with minimum false alarm ratio.

 Adjustable sensitivity level

 Adjustable relay time 2-40 sec.

 Selectable 2 choices for pulse detection options

 Built-in anti tamper switch

PACKAGE CONTENTS

 PIR Detector with Hidden Camera Unit x 1

 Mounting Bracket x 1

 Operation Instructions (this document) x 1

 Power adapter pigtail x 1

 Screws x 2

Product specificaties

Merk:	EverFocus
Categorie:	Bewakingscamera
Model:	ECMD200
Kleur van het product:	Wit
Gewicht:	130 g
Breedte:	70.104 mm
Diepte:	48.006 mm
Hoogte:	119.888 mm
Soort:	CCTV-bewakingscamera
Gebruikershandleiding:	Ja
Vormfactor:	Verborgen
Ondersteuning voor plaatsing:	Binnen
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Muur
Stroomuitvoer (volt):	12
Minimale belichting:	0.05 Lux
Aantal cameras:	1
Meegeleverde kabels:	DC
Nachtvisie:	Ja
LED-type:	IR
Vaste focale lengte:	3.7 mm
Formaat analoog signaal:	NTSC, PAL
Omvang optische sensor:	1/3 "
Type beeldsensor:	Super HAD CCD II
Camera sluitertijd:	1/50 - 1/100000 s
Interface:	BNC
Witbalans:	ATW
Type camerasluiter:	Elektronisch
Ruisonderdrukking:	Ja
Stroomverbruik:	10 mA
Signaal/ruis-verhouding:	52 dB
Power over Ethernet (PoE):	Nee
Inclusief schroeven:	Ja
Aantal TV lijnen:	600
Dag/nacht modus:	Ja
Maximum aperture number:	2
Montagebeugels meegeleverd:	Ja
Video uit:	1
Bewegingssensor:	Ja
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-10 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Output impedance:	75 Ohm
Detectie hoek:	100 °
Detectieafstand:	10 m
Automatische versterking control:	Ja
NTSC resoluties:	768 x 494 Pixels
Maximum output niveau:	1 Vpp