Emko ecoPID.4.6.1R.S.485 Handleiding
Pagina's 2 Thermostaat
Bekijk de handleiding van Emko ecoPID.4.6.1R.S.485 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
3
2
1
PO1
AL2
°C
°F
/
Eco
PO2
AL1
PO1
AL2
°C
°F
/
Eco
PO2
AL1
4
5
6
Eco PID, PID Temperature Control Unt�
- 3 dgt process (PV) and 4 dgt set (SV) dsplay�����
- Temperature sensornput (TC,RTD)�
- Programmable ON/OFF, P, PI, PD and PID control forms
- Adaptaton of PID Coeffcents to the system wth Self-Tune and Auto-Tune ����
- Programmable Heatng or Coolng Functons for Control Output ���
- Selectable Alarm Functons for Alarm Output�
- Seral RS485 Communcaton (optonal)����
Introducton Brochure. ENG EcoPID 01 V04 10/19�
Easy Access Dagram For Program Parameters�
Panel Mountng�
Enter Password wth ncrement��
or decrement buttons.
Approve password
wth Enter button�
Man ScreenPassword Screen�
Eco seres temperature controllers are desgned for measurng and controllng a ����
temperature value. They can be used n many applcatons wth ther TC and RTD �����
temperature measurement nput, mult-functon control outputs, selectable alarm ���
functons.�
They are manly used ��n glass, plastc, petro-chemstry, textle, automotve and machne �����
producton ���ndustres. Accurate and advanced controllng ��s performed wth selectable �
ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID functons.�
SPECIFICATIONS
Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)
Thermoresstance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)�
Measurement Range: Please refer to process �nput type selecton ��n process menu
parameters secton.�
Accuracy:
Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, whch one ��s greater) ±1 dgt max. ��
Thermoresstance (RTD):( ± 0.25% of full scale or ± 2ºC, whch one ���s greater) ±1 dgt ��
max.
Cold Juncton Compensaton:��Automatcally ±0.1°C/1°C�
Lne Compensaton:��Maxmum 10 Ohm�
Sensor Break Protecton:�Upscale
Samplng Cycle: �0.1 second
Input Flter:�Programmable
Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)
OUTPUT
Process Output:Relay (5A@250V at resstve load) or SSR Drver Output V���
(Maxmum 10mA, Max. 12V )�Z
Alarm Output:Relay (5A@250V at resstve load)V��
SUPPLY VOLTAGE (It must be determned ��n order)
230V (±15%) 50/60Hz - 2VAV
115V (±15%) 50/60Hz - 2VAV
100-240V 50/60Hz - 2VAV
24V(±%15) 50/60Hz - 2VAV
24V (±%15) 50/60Hz - 2VAW
10...30V - 2WZ
DISPLAY
Process Dsplay:�16 mm Red 3 dgt LED Dsplay���
Set Value Dsplay:�9 mm Orange 4 dgt LED Dsplay���
Led Indcators:�PO1 (SSR Process Output Status Led), PO2 (Relay
Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),
ºC, ºF LEDs
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Operatng Temperature:�0...50ºC
Humdty :��0-90%RH (none condensng)�
Protecton Class: �IP65 at front, IP20 at rear
Weght:�150 gr.
Dmenson:��48 x 48 mm, Depth: 86,5 mm
Panel CutOut:46 x 46 mm
*1 - ON/OFF Hysteress parameter s not actve unless parameter s set as .����
*2 - Soft Start parameters( , , ) s not actve unless parameter s set as .���
*3 - Soft Start Control Output and Soft Start Control Tme parameters s not actve f parameter����
s set as .�
*4 - PID control parameters are not actve unless parameter s set as .��
*5 -Alarm-2 parameters are not actve f parameter s set as .���
*6 - Communcaton parameters are not actve on devces have no communcaton module.������
*7 - If s dfferent from 0 and user enters to program menu wthout enterng the password����
P
rot menu s not shown.�
Note: User can ext from any parameter screen wthout savng the values by pressng button. If ����
no operaton for 120 seconds, devce automatcally return to man screen.����
Easy Access Dagram For Sensor Break Output�
Value From Man Screen�
Change the sensor break
output value wth ncrement��
or decrement buttons.
Press Enter button to save
new sensor break output value
and ext.�
PO2
PO1
AL1
AL2
°C
°F
/
Man Screen�
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/PO2
PO1
AL1
AL2
°C
°F
/
Man Screen�
Note1: User can ext from parameter screen wthout savng the ���
values by pressng button. If no operaton for 120 seconds, devce ���
automatcally exts from parameter screen.��
Note2: Sensor break output value can be adjusted on programmng �
secton too.�
Tune Operaton�
Startng the Tune operaton��
1- Enter to the parameter n menu and select �
or ,then press button for savng parameter and turn to man ��
screen. Or easly press button for 3 seconds* n man screen.���
2- Observe that blnks n set dsplay.���
*Only Auto tune can be started by ths way.�
Cancelng Tune operaton:��
1- If sensor breaks;
2- If tune operaton can not be completed n 8 hours;��
3- Whle heatng self tune s runnng, f process value becomes �����
greater than process set value;
4- Whle coolngself tune s runnng, f process value becomes less �����
than process set value;
5- Whle tune operaton s runnng, f user changes the process set �����
value;
6- Whle tune operaton s runnng, f user changes the �����
parameter n menu; �
Then tune operaton s canceled, devce contnues to run wth former �����
PID parameters wthout changng PID parameters.��
PID TEMPERATURE CONTROL UNIT
PID
Eco
Dmensons��
PO2
PO1
AL1
AL2
°C
°F
/
PID
Eco
48 mm / 1.89 nch�
48 mm / 1.89 nch�
6 mm / 0.24 nch�
80,52 mm / 3.17 nch�
Maxmum 9 mm / 0.35 nch��
1-Before mountng the devce n your panel, ���
make sure that the cutout s of the rght sze.���
2- Check front panel gasket poston.��
3-Insert the devce through the cutout. If the �
mountng clamps are on the unt, put out them ��
beforensertng the unt to the panel.���
4-Insert the mountng clamps to the two of �
desgnated holes that located four sdes of ��
devce. �
5-Drag the mountng clamps n drecton 5 ����
untl the devce completely mmoble wthn the ������
panel.
6-In order to remove devce push on the �
mountng clamp as shown wth arrow 6 and ��
pull back.
Access and Change Set Values
Press ncrement or decrement�
button to change process set value.
Press Enter button to save new
set value and return the man screen.�
Man Screen�
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
Man Screen�
PO2
PO1
AL1
AL2
°C
°F
/PO2
PO1
AL1
AL2
°C
°F
/
Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000
a
Note-1:User can ext from set value secton wthout savng the values by pressng button. If no �����
operaton for 120 seconds, devce automatcally exts from Set Value secton.�����
Note-2: Set value can be adjusted between Set Value Low and Hgh Lmt ( - ).���
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*1
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*5
*2
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*4
*2,3
*2,3
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*7
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*6
PO2
PO1
AL1
AL2
°C
°F
/
Press Program button
to access password screen.
Electrcal Wrngs���
The Devce wth One Relay:��
The Devce wth Two Relays:��
To reduce the effect of electrcal nose on devce, low voltage lne (especally sensor �����
������nput cable) wrng must be separetely from hgh current and voltage lne.If possble,
use shelded cable and sheld must be connected to ground only one sde.���
c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PO1
(Process Output 1)
SSR Output
12V
Max. 10mA
C
NO
AL1 / PO2
(Alarm Output 1 or
Process Output 2)
Process
Input
5A@250V
Seral Communcaton���
(RS485, Modbus RTU)
A+
B-
PID
Eco
PT-100
TC
Supply
Swtch�
L
N
Supply
Voltage
1A T
Fuse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PO1
(Process Output 1)
SSR Output
12V
Max. 10mA
C
NO
NO
AL1
(Alarm Output 1)
AL2 / PO2
(Alarm Output 2 or
Process Output 2)
Process
Input
5A@250V
5A@250V
Seral Communcaton���
(RS485, Modbus RTU)
A+
B-
PID
Eco
PT-100
TC
Supply
Swtch�
L
N
Supply
Voltage
1A T
Fuse
Warranty
EMKO Elektronk warrants that the equpment delvered s free from ����
defects n materal and workmanshp. Ths warranty s provded for a ������
perod of two years. The warranty perod starts from the delvery ���
date.
Ths warranty s n force f duty and responsbltes whch are ���������
determned n warranty document and nstructon manual performs ����
by the customer completely.
Mantenance�
Repars should only be performed by traned and specalzed ����
personnel. Cut power to the devce before accessng nternal parts. ���
Do not clean the case wth hydrocarbon-based solvents (Petrol, �
Trchlorethylene etc.). Use of these solvents can reduce the �
mechancal relablty of the devce. Use a cloth dampened n ethyl ������
alcohol or water to clean the external plastc case.�
Other Informatons�
Manufacturer Informaton:�
Emko Elektronk Sanay ve Tcaret A..���Ş
Demrta Organze Sanay Bölges Karanfl Sk. No:6 16369 �ş����
BURSA/TURKEY
Phone: +90 224 261 1900
Fax: +90 224 261 1912
a
Repar and Mantenance Servce Informaton:����
Emko Elektronk Sanay ve Tcaret A..���Ş
Demrta Organze Sanay Bölges Karanfl Sk. No:6 16369 �ş����
BURSA/TURKEY
Phone: +90 224 261 1900
Fax : +90 224 261 1912
Before commssonng the devce, parameters must be set n �����
accordance wth desred use. Incomplete or ncorrect confguraton �����
can cause dangerous stuatons.��
Because of lmted mechancal lfe of relay output contact, SSR ����
output s recommended whch the devce use PID control algortm. ����
The devce wth ON/OFF control algortm, hysteress parameter must ����
be set a sutable value for your system, to avod too much relay ��
swtchng.��
Vac,
Vdc,
Vdc or Vac can be appled�
: Communcaton Parameters ��(Only for devces wth RS-485 com.)��
: Protecon Menu Parameters�
: Communcaton accessng address of devce. (Default: 1) Modbus ����
Address: 40056
: Communcaton Baud Rate. (Default: 3) Modbus Address: 40057��
: 1200 Baud Rate.
: 2400 Baud Rate.
: 4800 Baud Rate.
: 9600 Baud Rate.
: 19200 Baud Rate.
: 38400 Baud Rate.
: Party Selecton for Communcaton. (Default: 0) Modbus Address: 40058����
: No Party.�
: Odd Party.�
: Even Party.�
: Stop Bt Selecton for Communcaton. (Default: 0) Modbus Address: 40059����
: 1 Stop Bt.�
: 2 Stop Bt.�
: Password for accessng to the programmng secton. It can be adjusted from 0 to ���
9999. If s 0, password screen s not seen. If s dfferent from 0 and user ����
enters to the menu pages wthout enterng the password, all the menus can be ��
observed except protecton menu . But devce does not allow to do any changes ��
�n parameters. (Default: 0) Modbus Address: 40063
: User default parameters. Ths parameter s used for savng all parameters to ���
restore later or restore all parameters saved before. If s chosen, all parameters �
saved before are restored. If s chosen, all parameters saved to restore later. If�
���s chosen, nothng s changed. (Default: ) Modbus Address: 40064
: Ths parameter s used for restore factory defaults. If s chosen, factory ���
defaults parameters restored. If s chosen, nothng s changed. (Default: ) ���
Modbus Address: 40065
Remove all nput/output connectons on termnals before restorng ����
parameters to user/factory defaults.
c
Modbus Addresses of Devce Operaton Info. (Read Input Regster)���
Modbus Address: 30000
Modbus Address: 30001
Modbus Address: 30002
Dsplayed Temperature Value�
Status of LEDs: bt.1 , bt.2 , bt.9 �ALR1�ALR2�°C
bt.10 , bt.11 , bt.12 �°F�PO2�PO1
Status of Devce: bt.0 Sensor Break Status��
Alarm Types
Alarm
Set
Alarm
Hysteress�
Alarm
Hysteress�
Alarm
Set
Process
Set
Process
Set
Alarm
Set
Alarm
Hysteress�
Alarm
Hysteress�
Process
Set
Process
Set
Alarm
Set
Alarm
Output
Alarm
Output
Alarm
Output
Alarm
Output
Process Value
Process Value
Process Value
Process Value
Process Hgh�
Alarm
Process Low
Alarm
Devaton Hgh���
Alarm
Devaton Low��
Alarm
: Alarm-1 set value. (Default: 300) Modbus Address: 40036
: Alarm-1 hysteress value. It can be adjusted from %0 to %50 of the scale�
( - ). (Default: 0) Modbus Address: 40037
: Alarm-1 type selecton. (Default: ) Modbus Address: 40038�
: Alarm-1 set low lmt parameter. It can be adjusted from operaton scale mnmum �����
to alarm-1 set hgh lmt. (Default: 0) Modbus Address: 40039���
: Alarm-1 set hgh lmt parameter. It can be adjusted from alarm-1 set low lmt to �����
operaton scale mnmum. (Default: 500) Modbus Address: 40040���
: Alarm-1 on Delay Tme. It can be adjusted from 0 to 9999 seconds. (Default: 0) �
Modbus Address: 40041
: Alarm-1 off Delay Tme. It can be adjusted from 0 to 9998 seconds. If t s hgher ����
than 9998, s seen on the screen and alarm latchng output s selected. In alarm ���
latchng output mode n order to make passve alarm outputs, press enter button at ���
man screen. (Default: 0) Modbus Address: 40042�
: Alarm-1 Menu Parameters
PID menu parameters can be seen only f parameter s .��
: If tune parameter s set to or , devce start to calculate PID ��
parameters automatcally. (Default: ) Modbus Address: 40027�
: Proportonal band. It can be adjusted from %1.0 to %100.0. (Default: 10.0) �
Modbus Address: 40028
: Integral Tme. It can be adjusted from 0 to 3600 second. (Default: 100) Modbus �
Address: 40029
: Dervatve Tme. It can be adjusted from 0.0 to 999.9 second. (Default: 25.0) ���
Modbus Address: 40030
: Output Control Perod. It can be adjusted from 0.5 to 150 second. (Default: 1.0) �
Modbus Address: 40031
: Set value offset. (Set + ) s used as set value n PID calculatons. Ths ����
parameter s used for shftng the proportonal band. It can be adjusted from (- /2) to ����
( /2). (Default: 0) Modbus Address: 40032
: PID Menu Parameters
:Alarm-2MenuParameters(Onlyfordevceswthtworelays)��
Alarm-2 menu parameters can be seen only f parameter s .��
: Alarm-2 set value. (Default: 400) Modbus Address: 40046
: Alarm-2 hysteress value. It can be adjusted from %0 to%50 of the Scale�
( - ). (Default: 0) Modbus Address: 40047
: Alarm-2 type selecton. (Default: ) Modbus Address: 40048�
: Alarm-2 set low lmt parameter. It can be adjusted from operaton scale mnmum �����
to alarm-2 set hgh lmt. (Default: 0) Modbus Address: 40049���
: Alarm-2 set hgh lmt parameter. It can be adjusted from alarm-2 setlow lmt to �����
operaton scale maxmum. (Default: 500) Modbus Address: 40050��
: Alarm-2 on delay tme. It can be adjusted from 0 to 9999 seconds. (Default: 0) �
Modbus Address: 40051
: Alarm-2 off delay tme. It can be adjusted from 0 to 9998 seconds. If t s hgher ����
than 9998, s seen on the screen and Alarm Latchng Output s selected. In ���
alarm latchng output mode n order to make passve alarm outputs, press enter ���
button at man screen. (Default: 0) Modbus Address: 40052�
Installaton�
In package,
-One pece unt��
-Two peces mountng clamp��
-One pece nstructon manual���
A vsual nspecton of ths product for possble damage occured �����
durng shpment s recommended before nstallaton. It s your ������
responsblty to ensure that qualfed mechancal and electrcal �������
techncans nstall ths product.����
If there s danger of serous accdent resultng from a falure or defect �����
�����n ths unt, power off the system and the electrcal connecton of the
devce from the system.�
The unt s normally suppled wthout a power swtch or a fuse. Use �����
power swtch and fuse as requred.��
Be sure to use the rated power supply voltage to protect the unt �
aganst damage and to prevent falure.��
Keep the power off untl all of the wrng s completed so that electrc �����
shock and trouble wth the unt can be prevented.��
Never attempt to dsassemble, modfy or repar ths unt. Tamperng ������
wth the unt may results n malfuncton, electrc shock or fre.������
Do not use the unt n combustble or explosve gaseous ����
atmospheres. Durng the equpment s putted n hole on the metal ����
panel whle mechancal nstallaton some metal burrs can cause ����
�njury on hands, you must be careful.
Montage of the product on a system must be done wth t’s mountng ���
clamp. Do not do the montage of the devce wth napproprate ����
mountng clamp. Be sure that devce wll not fall whle dong the �����
montage.
It s your responsblty f ths equpment s used n a manner not ���������
specfed n ths nstructon manual.������
Before begnnng nstallaton of ths product, please �����
read the nstructon manual and warnngs below ���
carefully.
Error Messages
Devaton Range��
Hgh Alarm�
Process
Set
Alarm
Set
Process
Set
Alarm
Hysteress�
Alarm
Output
Process Value
Process
Set
Alarm
Set
Process
Set
Process
Set
Alarm
Set
Alarm
Hysteress�
Alarm
Hysteress�
Alarm
Output
Process Value
Devaton Range��
Alarm
1-Sensor falure n analog nputs. Sensor connecton s wrong or there �����
��s no sensor connecton.
a
2-If programmng secton enterng password s dfferent from “0” and �����
user accesses to the parameter by enter button wthout enterng the ��
password and wants to change a parameter, the warnng message s ��
shown on the bottom dsplay as shown on the left. Devce does not ��
allow to do any changes wthout enterng the password correctly.��
a
3-If value that s read from the analog nput s lower than process set ���
low lmt parameter value ( ), value on the top dsplay starts to blnk ����
as shown on the pcture.�
a
4-If value that s read from the analog nput s hgher than process set ����
hgh lmt parameter value ( ), value on the top dsplay starts to ����
blnk as shown on the pcture.��
a
5-If value that s read from the analog nput s lower than sensor scale ���
low lmt, value on the top dsplay starts to blnk as shown on the ����
pcture.�
a
6-If value that s read from the analog nput s hgher than sensor scale ����
hgh lmt, value on the top dsplay starts to blnk as shownon the �����
pcture.�
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
Process
Set
Alarm
Set
Process
Set
Process
Set
Alarm
Set
Alarm
Hysteress�
Alarm
Hysteress�
Alarm
Output
Process Value
Devaton Band��
Alarm
: Control Menu Parameters
: Ths parameter determnes, whch output wll be Process control output. If s �����
chosen, process output s relay output, f s chosen, process output s SSR output. ����
(Default: ) Modbus Address: 40015
: Process Type Selecton. It can be (Heatng) or (Coolng).(Default: ) ���
Modbus Address: 40016
: Process Control Type Selecton. It can be or . (Default: ) Modbus �
Address: 40017
: Hysteress value. It can be adjusted from %0 to %50 of the Scale ( - ). �
If = , then ths parameter can be seen. (Default: 3) Modbus Address: 40018�
: Sensor Break Output Value. It can be adjusted from %0 to %100. (Default: 0.0)
Modbus Address: 40019
: The choce of dsplayed text on process value dsplay when sensor s broken.����
It can be or . (Default: ) Modbus Address: 40020
: Soft Start Set value. Devce operates n Soft Start mode, untl the temperature ���
reaches Soft Start set value. If s selected, Soft Start mode s dsabled. (Default: )���
Modbus Address: 40021
: Soft Start Control Output. Ths parameter determnes soft start mode control ��
output percentage. It can be adjusted from %10 to %90. (Default: 10.0) Modbus
Address: 40022
: Soft Start Control Tme. Ths parameter determnes soft start mode control tme. ����
(Default: 1.0) Modbus Address: 40023
:ProcessMenuParameters
: Process nput type selecton; (Default: ) Modbus Address: 40004��
: J type (Fe,Cu,N) Thermocouple , -199ºC,900ºC ; -199ºF,999ºF�
: J type (Fe,Cu,N) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF�
: K type (N,Cr,N) Thermocouple , -199ºC,999ºC ; -199ºF,999ºF��
: K type (N,Cr,N) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF��
: R type (Pt13%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF
: R type (Pt13%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF
: S type (Pt10%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF
: S type (Pt10%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF
: T type (Cu,Cu,N) Thermocouple , -199ºC,400ºC ; -199ºF,752ºF�
: T type (Cu,Cu,N) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF�
: L type (N,Cr,Co / N,Fe,Mn,Cu) Thermocouple , -150ºC,800ºC ; -199ºF,999ºF��
: L type (N,Cr,Co / N,Fe,Mn,Cu) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF��
: Cu-50 , -199ºC,200ºC ; -199ºF,392ºF
: Cu-50 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF
: Pt-100 , -199ºC,650ºC ; -199ºF,999ºF
: Pt-100 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF
: Unt Selecton. or can be chosen. (Default: ) Modbus Address: 40005��
: Operaton Scale mnmum (Low Lmt) value. It changes accordng to the process������
�nput type and scale. (Default: -199) Modbus Address: 40006
: Operaton Scale maxmum (Hgh Lmt) value. It changes accordng to the������
process nput type and scale. (Default: 900) Modbus Address: 40007�
: Process Set value Low Lmt. Mnmum set value s defned wth ths parameter.��������
It can be adjusted between Operaton Scale mnmum and maxmum ( - ) ����
values. (Default: -199) Modbus Address: 40008
: Process Set value Hgh Lmt. Maxmum set value s defned wth ths parameter.��������
It can be adjusted between Operaton Scale mnmum and maxmum ( - ) ����
values. (Default: 900) Modbus Address: 40009
: Dsplay offset for process value. It can be adjusted from -10% of scale to 10% of�
scale. It s added to the process dsplay value. (Default: 0) Modbus Address: 40010��
: Defne flter tme(sec) for dsplayed value. (Default: 1.0) Modbus Address: 40011����
Orderng Informaton��
Eco PID ( 48x48 DIN 1/16 )
Dmenson��
48x48 DIN 1/16
A
4
A
4.
B
.
C
.
D
S.
E
Outputs-1
1R
1 x Relay Output (5A@250V at Resstve Load) (NO,C)V��
C
2R
2 x Relay Output (5A@250V at Resstve Load) (NO,NO,C)V��
SSSR Drver Output (Max. 10mA, Max. 12V)�Z
Outputs-2
D
Communcaton��
0
None
485
RS-485 Communcaton��
E
10...30VZ
115V (±%15) 50/60HzV
230V (±%15) 50/60HzV
3
5
6
100-240V 50/60Hz1V
24V (±%15) 50/60HzV
Customer
7
9
24V (±%15) 50/60Hz2W
Supply VoltageB
Product specificaties
| Merk: | Emko |
| Categorie: | Thermostaat |
| Model: | ecoPID.4.6.1R.S.485 |
Heb je hulp nodig?
Als je hulp nodig hebt met Emko ecoPID.4.6.1R.S.485 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden