Emerson SA1-01002XLNB Handleiding

Emerson Niet gecategoriseerd SA1-01002XLNB

Lees hieronder de 📖 handleiding in het Nederlandse voor Emerson SA1-01002XLNB (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

GEIST™ SWITCH IRA

AIRFLOW MANAGEMENT DEVICE

Quick Installation Guide

SL-70388_REV0/VM-1177/590-2212-501A 1

Models:

SA1-01002XLNB

Type:

Rear Air Intake-Front (Port)

Exhaust Switches

CAUTION: Ensure the required

airflow for safe operation of

equipment is not compromised

when installing the Geist SwitchAir.

WARNING: Take precaution to

avoid interference with the switch

input power cords when installing

on a live unit.

1. Installing the adjustable

rails

Using customer provided

hardware, insert cage nuts into

the front two holes as well as

the rear extension tab hole of

each adjustable rail.

Select a 1U space in the rack

and hold one of the rails in

position between the front and

rear rack uprights. Lengthen or

shorten the adjustable rail by

adjusting the rear extension

tab, loosely fitting the rail

between the insides of the rack

uprights.

Attach the front of the

adjustable rail to the front

upright using only the top hole

of the 1U space. Leave the

bottom front hole open for later

use.

Attach the rear rail extension

tab to the rear rack upright. Use

the center hole of the 1U space

for this attachment.

Repeat the procedure for

installation of the adjustable rail

on the opposite side.

2. Installing the switch

Slide the network switch into

the rails. Using customer

provided cage nuts and screws,

mount the switch to the rear

Geist SwitchAir Airflow Management Device

Cage Nut Install Locations

Extension

tab

Geist SwitchAir Adjustable Rail to Rack Upright

FRONT

BACK

Rack uprights

Top hole

location

Top hole

location

Center hole

location

Center hole

location

Expand rails to fit

inside uprights

To contact Vertiv Technical Support: visit www.VertivCo.com

trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no

responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

GEIST™ S A AIRFLOW MANAGEMENT DEVICE WITCH IR

Quick Installation Guide

2 SL-70388_REV0/VM-1177/590-2212-501A

rack uprights using the 1U

space’s top and bottom holes.

3. Mounting the SwitchAir

unit

SwitchAir is not in the fully

extended position when

shipped from the factory. Pull

evenly on the chassis mounting

tabs for the desired depth.

Insert SwitchAir into the rails

and push unit back until the

insert comes in contact with

the network switch and the

front chassis mounting tabs are

flush with the rack front rails.

Install the bottom chassis

screws on both sides.

Geist SwitchAir and Network Switch Installation

Geist SwitchAir Rack Installation Complete

Bottom hole

location

Top and bottom

hole locations

Expand to

fit

Product specificaties

Merk:	Emerson
Categorie:	Niet gecategoriseerd
Model:	SA1-01002XLNB
Kleur van het product:	Zwart
Gewicht:	11340 g
Breedte:	323.8 mm
Diepte:	533.4 mm
Gebruikershandleiding:	Ja
Frame type:	Open frame
Duurzaamheidscertificaten:	RoHS
Rack-montage:	Ja
Type koeling:	Passief
Rackcapaciteit:	1U