EmberGlo ES10PB Handleiding
EmberGlo
Niet gecategoriseerd
ES10PB
Bekijk gratis de handleiding van EmberGlo ES10PB (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.3 sterren uit 7 reviews. Heb je een vraag over EmberGlo ES10PB of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
Installation and Service Instructions
Quality Designed for Proven Performance
Printed in USA
8470 77
AVOID ERROR IN PARTS SELECTION. When ordering use
complete EMBERGLO Part Number and Description. Furnish
Model Number, Bill of Material Number and Serial Number (if
available) from the specifi cation plate found on the product.
IMPORTANT: Availability of parts as well as specifi cations are
subject to change without notice. Please consult factory for
item availability.
!
EmberGlo
A Div of Midco® International Inc.
4140 West Victoria Street
Chicago, Illinois 60646
toll free 866.705.0515
tel 773.604.8700
fax 866.580.8700
web www.emberglo.com
e-mail sales@emberglo.com
SAFETY INFORMATION TERMS: The following terms are used to identify hazards, safety precaution of special notations
and have standard meanings throughout this manual. They are printed in all capital letters using a bold type face as shown
below, and preceded by the exclamation mark symbol. When you see the safety alert symbol and one of the safety information
terms as shown below, be aware of the hazard potential.
DANGER: Identifi es the most serious hazards which will result in severe personal injury or death.
WARNING: Signifi es a hazard that could result in personal injury or death.
CAUTION: Identifi es unsafe practices which would result in minor personal injury or
product and property damage.
!
!
ES10 Series - Designed to operate without distilled water,
direct water hookup, stainless steel construction
Specifi cations:
• 240 volts 60HZ AC 3200 watts, max 13.3 amps or
208 volts 60HZ AC 2400 watts, max 11.6 amps
• Manual pump (push button)
• Open generator
• Full pan size
• Spring loaded adjustable hinge with 60° or 90° opening
• Food grid
• Quick connect fi ttings
This manual contains suffi cient information for installation of the
EmberGlo steamer in normal locations.
In the United States, installation must conform with local codes.
PURCHASER: Retain these instructions for future use.
Post in a prominent location near the steamer.
CODE COMPLIANCE IS THE SOLE RESPONSIBILITY OF
THE INSTALLER.
Limited Warranty
The Limited Warranty can be found on www.emberglo.com. To
fi le a claim follow the directions given in the warranty, or contact
EmberGlo by mail, phone or e-mail.
4140 W. Victoria Street / Chicago, IL 60646
Phone: 866 705 0514 Fax: 866 580 8700
E-mail: orders@emberglo.com
This warranty does not apply to damages resulting from
accident, misuse, abuse or alteration.
Do not store or use gasoline or other fl ammable liquids and
vapors in the vicinity of this or any other appliance.
NOTE: EmberGlo ES10 Series steamers use a cast aluminum
steam generator with two cast in electric heating elements.
For best steaming, the generator casting should contain some
mineral deposits. During fi nal inspection each generator casting
is pre-seasoned with a solution of baking soda and water. The
water marks and mineral deposits seen on a new generator
casting when the perforated food pan is removed is your as-
surance that the unit has passed fi nal inspection test and will
readily produce steam.
No equipment may be returned without written authorization
from EmberGlo (or Midco International Inc.). Returned goods
must be shipped prepaid to the factory.
WARNING: Additions, changes, conversions and
service must be performed by an authorized EmberGlo
representative or service agency. Use only EmberGlo specifi ed
and approved parts.
CAUTION: Cooking equipment should be used in
an environment protected by an automatic fi re suppression
system. Consult the National Fire Protection Association NFPA
Code 96 or the latest edition of Standards for Installation of
Equipment for Removal of Smoke and Grease-Laden Vapors
From Commercial Cooking Equipment.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating
and maintenance instructions thoroughly before
installing or servicing this equipment.
!
U
L
1224
ES10 Series
Top Open / Full Pan
Counter Top Steamer
ES10PB: Push Button Operation with Direct
Water Connect
ES10PB
EmberGlo A Division of Midco International Inc
2
8470 77
ES10 Series - Installation
ES10 steamers feature a 4 deep full size steam table pan. The steamer lid is equipped with two ″
counter-balanced spring hinges and off ers two handles on the front of the lid, projecting forward.
Dimensions
Inches Centimeters
HEIGHT (lid closed) 9 3/4″ 24.77
HEIGHT (lid open 90 degrees) with lid handle mounted on
front corner of lid, projecting forward 29″ 73.66
WIDTH 22 1/2″ 57.15
DEPTH 22″ 55.88
____________________________________
Electrical Specifi cations: The generator casting contains two heating elements, each rated for
1600 Watts, 13.3 amps, 120 Volts, 60 Hz. Models are available for use on 50 Hz. (non-USA, export
only) electrical service. Call your distributor for more information. Standard units are furnished with a
six foot, four conductor (2 Hot/1 Neutral/1 Ground) cord. This cord is equipped with a male twist-lock
plug and matching loose female receptacle for convenient fi eld installation.
____________________________________
Electrical Installation: Female twist-lock receptacle, supplied loose with the steamer, should be
installed by a qualifi ed electrician. Refer to wiring diagram, (Figure 3).
NOTE: Female receptacle must be wired to assure that voltage to the individual heating elements
does not exceed 150 volts. G terminal is wired to Ground and W terminal is wired to Neutral. Protect
circuit with a 15 amp double pole circuit breaker.
When choosing a location for the steamer, be sure that there is adequate space over the unit to lift
lid completely.
1. All ES10 models should be placed on level surface. The power cord should be plugged into a
240 volt, single phase 60Hz grounded outlet.
2. ES10PB: Connect water hose assembly to water supply system. The supply end has 1/8 ″
female pipe fi tting and should be attached down stream to a shut-off valve. Steamer end of
hose has a quick connect fi tting which snaps onto mating fi tting on steamer. This fi tting has
an automatic shut-off valve that allows steamer to be disconnected without shutting off water
supply. After connecting, turn on water and check for leaks.
3. EmberGlo steamers do not require a separate hood for vapor produced during operation
according to the Uniform Mechanical Codes per the International Conference of Building
Offi cials Code. There are no requirements in NSF Standard 4 (2006e) for steamers to have
ventilation.
4. To adjust the angle of the lid to 60° or 90°:
1. With the lid closed, loosen and remove slotted screw. Set aside.
2. Remove lid stop by sliding it up and away from the steamer.
3. Adjust lid stop for desired position (60° or 90° open) and place on steamer.
4. Insert and tighten slotted screw.
See Figure 1a, 1b and 1c for orientation of lid stop.
Factory default setting is 60°.
__________________________________________
EmberGlo A Division of Midco International Inc
8470 77
3
ES10 Series - Operation
Before Using:
1. Remove the protective plastic covering.
2. Connect to a water supply using direct connect fi ttings.
3. Plug into 240 VAC outlet.
4. Push power switch (item 4 in Figure 2) to the ON position (light on) and allow approximately
15-20 minutes to reach operating temperature.
5. Test to make sure unit will generate steam.
6. Press the steam button (item 3 in Figure 2) several times to remove the air from the system,
you will notice it will start to steam. The steamer is now ready to use.
General Operating Instructions:
1. Open lid, place food on grid and close lid.
2. ES10PB: Push the steam button momentarily for each operation. Do not hold button more than
one second.
Note: After installation, operate several times until the water hose fi lls with water.
3. Open lid and remove food.
4. For effi ciency and safety purposes, keep lid closed when not in use. This keeps the food pan
hot and reduces condensation in the steam chamber.
To shut off , push power switch to OFF position (light off ).
__________________________________________
1
2
Figure 1a
Back of ES Series Steamer
60° Opening Position
Figure 1c
Figure 1b
Back of ES Series Steamer
Lid Stop Reversed
90° Opening Position
90°
60°
Item # Part # Description
1 HW1-099 #8-32 X 5/16 Slotted ″
Pan Head Screw 18ss
2 1421-21 Lid Stop
Item # Part # Description
1 2512-22 Switch Panel
2 5622-00 Name Plate
3 8423-36 Steam Push Button
4 8423-34 On/off Switch
Figure 2
ES10PB Steamer - Front Panel
Product specificaties
| Merk: | EmberGlo |
| Categorie: | Niet gecategoriseerd |
| Model: | ES10PB |
Heb je hulp nodig?
Als je hulp nodig hebt met EmberGlo ES10PB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd EmberGlo
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
Handleiding Niet gecategoriseerd
- Gretsch
- Fellow
- Gridbyt
- BLUEPALM
- Pure 100
- Tonar
- Vantec
- Stäubli
- Blafili
- Gustavsberg
- IsoTek
- IFM
- Coca-Cola
- Cricut
- Gitzo
Nieuwste handleidingen voor Niet gecategoriseerd
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025