Electro Harmonix Operation Overlord Handleiding

Electro Harmonix Niet gecategoriseerd Operation Overlord

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Operation Overlord (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

OPERATION OVERLORD

Stereo Multi-Instrumental Overdrive

Congratulations on your purchase of the OPERATION OVERLORD, an advanced,

full-featured stereo overdrive and distortion pedal. With the OVERLORD’s broad

range of options and controls you can dial in great drive sounds for keyboards,

synths, guitars, basses, and more. Active 3-band EQ controls, footswitchable

BOOST mode, and a dry blend provide versatility for different tones and

instruments. The OVERLORD also features two independent distortion channels

for use with stereo setups. Whatever your rig, use the OVERLORD to dial in your

tonal inspiration.

- MODES OF OPERATION: NORMAL VS. BOOST -

The OVERLORD operates in two modes: NORMAL and BOOST. The NORMAL

mode uses three amp-like JFET gain stages for low to medium gain sounds.

When in NORMAL mode, use the GAIN knob to control the amount of overdrive.

The BOOST mode adds a classic pedal-style overdrive circuit before the JFET

stages to increase overall distortion. BOOST is engaged with the BOOST

Footswitch and is active when the blue LED is lit. In BOOST mode, both the

GAIN and BOOST knobs are active, and the BOOST knob controls how much

additional gain from the BOOST circuit is fed into the main JFET circuit.

- USING BOOST MODE AS AN INDEPENDENT PEDAL –

The BOOST circuit can also be configured to operate on its own, OVERLORD’s

without the NORMAL mode’s JFET gain stages. To enable this, remove the 4

screws on the bottom of the OVERLORD and locate the slide switch at the

bottom of the PCB. Being careful not to touch any components, slide the switch

in the direction labeled “BOOST INDEPENDENT ”.

When independent BOOST mode is enabled, the BOOST circuit is active by itself

when the BOOST LED is lit and the BYPASS (red) LED is off. In this setting, the

GAIN and BOOST knobs are disabled. All other controls function normally. When

NORMAL mode is engaged (red LED lit), the pedal functions as usual, with the

BOOST mode feeding into the JFET gain stages.

- CONTROLS -

GAIN Knob – The knob controls the amount of overdrive/distortion. As GAIN

you turn GAIN clockwise, the amount of input gain increases.

BOOST Knob The BOOST knob controls the amount of extra gain fed into the –

main circuit when the BOOST and NORMAL modes are engaged (both LEDs lit).

As BOOST is turned clockwise, the amount of distortion increases.

DRY Knob The DRY knob mixes a clean unaltered signal with the distortion –

produced by the OVERLORD. At the minimum position of the DRY knob, the

output is 100% overdrive effect, and at the maximum position the output is

100% clean. This function is useful for preserving the harmonic integrity of your

playing, which is especially useful for keyboards or bass. For guitarists, this

feature can be useful if you are stacking the OVERLORD with other drive pedals,

or are playing it through an overdriven amplifier.

INPUT LVL Switch This switch controls the overall input level of your –

instrument into the OVERLORD. Use it to set an appropriate gain level for a

variety of instruments. Set the switch to HI for low-level instruments, like a

single-coil guitar or vintage electric piano. Set the switch to NORM for

humbucker guitars and most modern keyboard workstations. Use the LO setting

for high-output instruments, like some synthesizers or boosted guitars.

Tip: The GAIN Knob, INPUT LVL switch, and DRY knob all work together. If

the INPUT LVL switch is set properly, turning the DRY knob should not

significantly change the overall volume. However, varied settings of the INPUT

LVL switch could produce some interesting higher- or lower-gain sounds. Feel

free to experiment with this switch – setting it “wrong” might sound great,

and won’t damage the circuit!

BASS Knob Active control of the level of the bass frequency range. –

MID Knob Active control of the level of the middle frequency range. –

TREBLE Knob Active control of the level of the treble frequency range. –

VOL Knob This knob controls the overall volume output of the OVERLORD. As –

this knob is turned clockwise, the output level increases.

BYPASS Footswitch red LED and – footswitch selects whether the This

OVERLORD is engaged or in buffered bypass mode. When the effect is engaged,

the red LED will be lit.

BOOST Footswitch and blue LED – This footswitch toggles Boost mode on

and off. When in Boost mode, the blue LED will be lit.

L / R INPUT Jacks – ¼” jack These s are the audio inputs. The OVERLORD can be

used with either mono or stereo inputs. When using only one input, we suggest

you use the MONO/L input. The input impedance at each jack is . 1M

L / R OUTPUT Jacks These s are the audio output from the OVERLORD– ¼” jack .

If using the OVERLORD as a mono effect (i.e. one instrument into one amplifier)

we suggest using the MONO/L input and output jacks. When using stereo inputs

and stereo outputs, each signal is routed through an independent distortion

circuit. The output impedance at each jack is 220 . 

Tip: The OVERLORD can also be used with a mono input and stereo output.

This can be useful for splitting your signal into two amplifiers, or sending one

signal to a mixing board and one to an amplifier.

9V Power Jack – Plug the output of the OVERLORD’s supplied EHX9.6DC

200mA AC Adapter into the 9V power jack located at the top of the pedal. The

OVERLORD requires 90mA with a center negative plug.

- WARRANTY INFORMATION -

Please register online at http://www.ehx.com/product-registration or complete and return the enclosed

warranty card within 10 days of purchase. Electro-Harmonix will repair or replace, at its discretion, a

product that fails to operate due to defects in materials or workmanship for a period of one year from

date of purchase. This applies only to original purchasers who have bought their product from an

authorized Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the

unexpired portion of the original warranty term.

If you should need to return your unit for service within the warranty period, please contact the

appropriate office listed below. Customers outside the regions listed below, please contact EHX

Customer Service for information on warranty repairs at info@ehx.com or +1- - -8300. USA and 718 937

Canadian customers: please obtain a Return Authorization Number (RA#) from EHX Customer

Service before returning your product. Include with your returned unit: a written description of the

problem as well as your name, address, telephone number, e-mail address, and RA#; and a copy of

your receipt clearly showing the purchase date.

United States & Canada

EHX CUSTOMER SERVICE

ELECTRO-HARMONIX

c/o NEW SENSOR CORP.

55-01 2ND STREET

LONG ISLAND CITY, NY 11101

Tel: 718- - 937 8300

Email: info@ehx.com

Europe

JOHN WILLIAMS

ELECTRO-HARMONIX UK

13 CWMDONKIN TERRACE

SWANSEA SA2 0RQ

UNITED KINGDOM

Tel: +44 179 247 3258

Email: electroharmonixuk@virginmedia.com

This warranty gives a purchaser specific legal rights. A purchaser may have even greater rights

depending upon the laws of the jurisdiction within which the product was purchased.

To hear demos on all EHX pedals visit us on the web at www.ehx.com

Email us at info@ehx.com

Product specificaties

Merk:	Electro Harmonix
Categorie:	Niet gecategoriseerd
Model:	Operation Overlord

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Operation Overlord stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Electro Harmonix

Electro Harmonix Germanium OD Handleiding

25 April 2024

Electro Harmonix 2X12 Speaker Cabinet Handleiding

15 Maart 2024

Electro Harmonix Rerun Handleiding

12 Maart 2024

Electro Harmonix 15Watt Handleiding

9 Januari 2024

Electro Harmonix Hum Debugger Handleiding

7 December 2023

Electro Harmonix Deluxe Memory Man 1100-TT Handleiding

16 November 2023

Electro Harmonix Triboro Bridge Handleiding

9 November 2023

Electro Harmonix Deep Freeze Handleiding

9 November 2023

Electro Harmonix Oceans 3-Verb Handleiding

9 November 2023

Electro Harmonix Walking On The Moon Handleiding

30 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024