Duronic TM61 Handleiding

Bekijk gratis de handleiding van Duronic TM61 (4 pagina’s), behorend tot de categorie Kabels voor pc's en randapparatuur. Deze gids werd als nuttig beoordeeld door 16 mensen en kreeg gemiddeld 4.1 sterren uit 5 reviews. Heb je een vraag over Duronic TM61 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

07

ＣＡＵＴＩＯＮ：　ＤＯ　ＮＯＴ　ＥＸＣＥＥＤ

ＭＡＸＩＭＵＭ　ＬＩＳＴＥＤ　ＷＥＩＧＨＴ

ＣＡＰＡＣＩＴＹ．ＳＥＲＩＯＵＳ　ＩＮＪＵＲＹ

ＯＲ　ＰＲＯＰＥＲＴＹ　ＤＡＭＡＧＥ　ＭＡＹ

ＯＣＣＵＲ！　

Power Input

100V-240V

Speed

25 mm/s

Load Capability

176 lbs / 80 kg

Motion Noise

＜55dB

RATED

●

Length Adjustment Range: 100-160cm

●Height Adjustment Range: 72-120cm

●

3-Level Height Memory Function

Adjust the desk upwards

Adjust the desk downwards

Height Preset 1

Height Preset 2

Height Preset 3

Press for 5 seconds, the display will show 'RES' keep pressing the key until the legs move down to

the lowest position.

To set Height Preset, press the S button until the LED Display flashes then press Preset 1, 2, 3 to

program preset.

S

1

3

2

Reset

Protection mode (auto lock screen mode)

Control Panel Keys

Over-heating

Hot

E10

E20

E02

E32

E31

E60

protection

Detection

alarm

Overload

protection

Rebound

protection

Overvoltage

alarm

Undervoltage

alarm

Step out

alarm

Breaking

protection

Alarms when continuously in motion for 2 minutes.

Power back on and wait for at least 18 minutes before adjusting height again.

Alarms when motor sensor cannot be detected.

Turn off power, check the connection of motor and control box, and then power back on.

If alarm sounds when the desk is moving up, remove loads off the desk and try again.

Alarms when vibrated, collided or inclined during height adjustment. Check if there is anything

in the way of desk motion. Then proceed to the reset the motor.

If it alarms when desk is moving down, turn off the power, remove loads off the desk and re-try.

It alarms when voltage is higher than anticipated value. Turn the power off, check the connection

between power and control box. If no problem, power it back on.

It alarms when voltage is lower than required value. Turn the power off, check the connection

between power and control box. If no problem, power it back on.

It alarms when height difference between left leg and right leg exceeds the set value.

Power off first. Check whether the left leg and the right leg are in the same height. If not, re-do

Installation Step 3 to make them same height. Power it back on.

It stops and enters protection state when motor cables or manual control cables are removed

or disconnected accidentally; goes back to normal after it’s reconnected and alarm is cleared.

Engineering Mode

ChangeDisplayed

Unit()

Change

Brightness(br)

CollisionForce

Detection(CF)

Long press the button, “S--”shows and flashes. Press again and the displayshows “Un”.

shows “Un”.

“OFF”, Low (L), Normal (n) or Heavy (H) collision force detection.

SS

Press to save your choice.

S

Low (L), Normal (n) or High (H) brightness.

Press to save your choice.

S

Long press the button, “S--”shows and flashes. Press again and the display

SS

shows “Un”. Long press the button, “S--”shows and flashes. Press again and the display

SS

Press to save your choice.

S

Press or to switch to

“CF”. Press to select. Press or to switch between

S

Press or to switch to

“br”. Press to select. Press or to switch between

S

Press to select. Press

or to switch between“ ”(metric) or “ ” (imperial).

S

TM61 BK

TM61 WE

Product specificaties