DS18 NXL-12SUB Handleiding
Bekijk gratis de handleiding van DS18 NXL-12SUB (4 pagina’s), behorend tot de categorie Subwoofer. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.4 sterren uit 2 reviews. Heb je een vraag over DS18 NXL-12SUB of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
MARINE & MOTORSPORTS 12” SUBWOOFER
NXL-12SUb
PACKING INCLUDE
MOUNTING
WARNINGS
FEATURES
1. Be Sure to carefully read and understand the instructions
before attempting to install these speakers.
2. For safety, disconnect the negative battery terminal from the battery
prior to beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting speaker in place
4. Use high quality connectors for a reliable installation and to minimize signal or power loss
5. Think before you drill. Be careful not to cut or drill gas tanks, fuel lines, brake or hydraulic
lines, vacuum lines or electrical wiring when working on any vehicle. If installing in a boat,
take care not to cut or drill through the mail hull.
6. Never run wires underneath the vehicle. Running the wires inside the vehicle or hull
area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to
protect any wires routed through metal - especially the firewall.
1. Determine where the speakers will be mounted. Ensure an area large enough for the
speaker to mount evenly. Be sure that the mounting location is deep enough for the
speaker to fit; only mount to a flat surface. Use extra caution when mounting on panels
with ureathane foam.
2. Refer to the specification chart to determine the proper diameter hole to cut for the speaker.
3. Mark the locations for the mounting screws. Drill the holes with a 0.75” bit.
4. Feed the speaker wires through the cutout and connect to the speaker terminals. Be sure
to observe proper polarity when connecting the wires. The speaker’s positive terminal is
indicated with a “+”.
5. Fit the speaker and mount into place using six (6) screws.
6. Tighten the screws until the speaker is in place.
12” Marine & Motorsports Subwoofer
1 x 1.5M #16 Speaker Input Wired with Fast Terminal
1 x 1.5M #22 RGB LED Power Input Wired with Fast Terminal
6 x M5.2 Phillips Inner Hex Head 304 Stainless Steel (4mm Hex Tool)
MARINE & MOTORSPORTS 12” SUBWOOFER
IP65 Marine Grade Compliant 100% UV Stable
Continuous Power Handling: 350W RMS
Peak Music Power: 700W MAX
Nominal Impedance: 4 Ohms
Sensitivity: 91dB
Frequency Response: 30Hz-500Hz
Components
Y35 Ferrite Main Magnet and Reverse N40H (Neodymium) Magnet
Integrated LED-RGB Lighting
Materials
Waterproof Injection PP Cone
Soft Rubber Surround
316 Stainless Metal Mesh
Injection ASA Grill with Gloss UV-Coating
PC Injection Molded Composite Basket with Gloss UV-Coating
BT Control Module & App (LED-BTC) For Multi-Function for
RGB LED Lighting (sold separately)
Mounting Depth: 5.75"/146mm
Cut-Out Diameter: 10.71"/272mm
Overall Diameter: 12.81"/325.3mm
Overall Height: 7.68"/195mm
We Reserve the Right to Change Products and Specifications at Any Time
Without Notice. Images May or May Not Include Optional Equipment.
Black wire ”BK” connected to battery Positive (+) 12V then choose one color:
For Green color light: “G” Connected to Battery Negative (-)
For Red color light: “R” Connected to Battery Negative (-)
For Blue color light: “B” Connected to Battery Negative (-)
For Purple color light: “R” and “B” Connected to Battery Negative (-)
For Yellow color light: “R” and “G” Connected to Battery Negative (-)
For Cyan color light: “B” and “G” Connected to Battery Negative (-)
For White color light: “R”, “B” and “G” three wires Connected to Battery Negative (-)
7. LED CONNECTIONS - There are two options to choose from:
If you have an LED Control Module (LED-BTC), connect as shown in the following diagram.
To connect without LED Control Mocule (LED-BTC), connect as shown in the
following diagram:
Download the app
12.81” / 325.3mm
Subwoofer
30-500Hz
2” (50mm)
350 Watts RMS / 700 Watts MAX
33Hz
0.341
2.666cu.ft / 75.492l
91dB
0.787” / 20mm
11.81” / 300mm
5.75”/ 146mm
Model
NXL-12SUB
Nominal Diameter
Type
Nominal Impedance
(ohms)
Frequency Response
(Hz)
Voice Coil Diameter
Power Handling
Fs - Free Air Resonance
(Hz)
Qts
Vas - Cu. Ft
(Liter)
Sensitivity (1w/1m)
Xmax
Mounting Hole
Mounting Depth
4 ohms
Green LED (-)
Black 12V DC (+)
White Speaker (+)
Grey Speaker (-)
Red LED (-)
Blue LED (-)
+
-
+-
BATTERY
Example of Green Light Connection:
Green LED (-)
Black 12V DC (+)
White Spe er (+)ak
Grey Speaker (-)
Red LED (-)
Blue LED (-)
1
2
Work with Android
and Iphone
The LED-BTC is an app based, BT Solution for RGB LED lighting control.
The applications are truly limitless, lending to all types of environment,
wether wet or dry. (SOLD SEPARATELY).
Product specificaties
| Merk: | DS18 |
| Categorie: | Subwoofer |
| Model: | NXL-12SUB |
Heb je hulp nodig?
Als je hulp nodig hebt met DS18 NXL-12SUB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Subwoofer DS18
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
Handleiding Subwoofer
- Philips
- PSB
- ButtKicker
- Mac Audio
- QTX
- Match
- HK Audio
- Taga Harmony
- Cerwin-Vega
- Dayton Audio
- Orion
- Tivoli Audio
- Crestron
- Piega
- Marquant
Nieuwste handleidingen voor Subwoofer
15 Juli 2025
15 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025