Dormakaba Mundus Premium PT70 Handleiding

Dormakaba Niet gecategoriseerd Mundus Premium PT70

Lees hieronder de đź“– handleiding in het Nederlandse voor Dormakaba Mundus Premium PT70 (15 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/15
MUNDUS Premium PT41
Transom and Sidelite Connector fittings
with one or two fins
Installation instructions
942004 – 05-2018
| | EN
2MUNDUS Transom Connector Fittings 05-2018942004
dormakaba MUNDUS Premium PT41
Installation Instructions
Table of Contents
Table of contents
1  Technical specifications 3
1.1 Overview 3
1.1.1 General information 3
1.1.2 Intended use 3
1.1.3 Glass requirements/fittings/mounting 3
1.1.4 Requirements for glass panel 3
1.1.5 Safety instructions 3
1.1.6 Symbols used - Safety/Installation 3
1.1.7 Maintenance, care, repair 3
1.1.8 Disposal 3
1.2 Door dimensions 4
1.3 Glass thickness/pivot point 5
angle specifications 5
1.4 Tempered laminate glass (TLG)
and adhesive specifications 6
2 Installation instructions 7
2.1 Overall 7
2.2 Install gaskets 7
2.3 Install plates and remaining fitting parts 8
2.4 Plumb and level the fitting 8
2.5 Secure the fitting 9
2.6 Setting the pivot/blank/stop 9
2.7 Door alignment 10
2.8 Door adjustments 10
2.9 Apply adhesive: (For TLG applications ONLY.) 11
2.10 Install covers 11
2.11 Install fin plate(s) and fasteners 12
2.12 Plumb and level the fin fitting 13
2.13 Secure the fin fitting 13
2.14 Apply adhesive: (For TLG applications ONLY.) 14
2.15 Install covers 14
dormakaba MUNDUS Premium PT41
Installation Instructions
942004 05-2018MUNDUS Transom Connector Fittings 3
Technical specifications
1  Technical specifications
1.1 Overview
These instructions are for installation of the PT41
Transom Connector Fittings with fin(s) for the following
mounting and style versions:
1. Glass mounting
1.1.1 General information
• dormakaba requires use of tempered laminated or
tempered monolithic glass.
• dormakaba glass hardware is not suitable for harsh
environment; for example, applications where
chemicals (e.g. chlorine) are used such as indoor
swimming pools, saunas, or salt-water pools.
• Do not swing doors with excessive force. Install
limiting stop to prevent door from opening too far.
1.1.2 Intended use
• For pivoting doors in indoor or covered areas only.
• For manual slowly opening and closing only.
1.1.3 Glass requirements/fittings/mounting
• The substructure/wall must be able to bear
permanent loads, be level (max. tolerance: 1/16”
[2] per 39” [1m]).
• Fasteners must be sufficiently dimensioned for the
substructure/wall and weight of the door.
• When adjusting glass components, always stick to
the required clearance for the respective hardware.
Adjust clearance so glass does not come in contact
with any hard surfaces such as glass, metal or
concrete.
• Do not use excessive force when installing the glass
(avoid over tightening screws.)
1.1.4 Requirements for glass panel
• dormakaba requires use of fully tempered glass,
which complies with ASTM C 1036 and ASTM C
1048. Secondary heat soaking processes are
optional but not required. This applies to both
tempered monolithic and tempered laminated
glass.
• Clamping area must be flat and uncoated (no
self-cleaning coating!)
• Never use glass with conchoidal fractures and/or
damaged edges.
1.1.5 Safety instructions
• Installation requires two people.
• Always wear protective clothing.
• Only properly qualified and specially trained staff is
authorized to mount dormakaba glass hardware.
• Due to crushing hazards and possible injury caused
by breakage of glass during mounting,
corresponding protective clothing (especially gloves
and protective goggles) is required.
• Never clamp metal fitting hardware directly to
glass surface.
1.1.6 Symbols used - Safety/Installation
CAUTION
Mounting components must meet the
requirements of substructure/wall and door
weight. Please read the technical information
for fittings.
WARNING
Risk of breaking glass. When installing the
door, support the door panel with a block of
wood or similar object.
TIPS AND RECOMMENDATIONS
Information note
CLOSING EDGE OF DOOR
1.1.7 Maintenance, care, repair
• Immediately replace damaged parts.
• Always use original dormakaba parts.
• Clean clamping area with alcohol-based standard
commercial cleaning agent before mounting the
glass hardware.
• Use a damp cloth for occasional cleaning.
• Always use silicone - and oil-free cleaners (e.g.
acetone).
• Check glass hardware at regular intervals for
proper positioning, smooth operation and correct
adjustment.
• High traffic door systems require inspection by
properly qualified staff (specialized companies or
installation firms.)
• Function of fittings is recommended to be
inspected every 500,000 movements by a specialist.
1.1.8 Disposal
Disposal in accordance with local, state and national
regulations.


Product specificaties

Merk: Dormakaba
Categorie: Niet gecategoriseerd
Model: Mundus Premium PT70

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba Mundus Premium PT70 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Dormakaba

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd