Dnipro Metamorph Handleiding
Dnipro
Synthesizer
Metamorph
Bekijk gratis de handleiding van Dnipro Metamorph (1 pagina’s), behorend tot de categorie Synthesizer. Deze gids werd als nuttig beoordeeld door 16 mensen en kreeg gemiddeld 5.0 sterren uit 8.5 reviews. Heb je een vraag over Dnipro Metamorph of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/1
GLIDE GLIDE
REVERS
CLOCKSTOP CV IN
RESET
TRIGS
CV OUTS
GATE
GATE
GATE
GATE
CHANNEL 1 CHANNEL 2
STAGE 1
STAGE 2
STAGE 3
STAGE 4
CHANNEL 3
USER GUIDE V1.0
COMMON LAYOUT OVERVIEW
CONTROLS AND FUNCTIONS
HOW TO LINK TWO MODULES
GLIDE GLIDE
REVERS
CLOCKHOLD CV IN
RESET
TRIGS
CV OUTS
GATE
GATE
GATE
GATE
GLIDE GLIDE
REVERS
CLOCKHOLD CV IN
RESET
TRIGS
CV OUTS
GATE
GATE
GATE
GATE
CONTROLLERSEQUENCED
GLIDE GLIDE
REVERS
CLOCKHOLD CV IN
RESET
TRIGS
CV OUTS
GATE
GATE
GATE
GATE
CONTROLLERSEQUENCED
4
6
2
3
1
781011
1
2
3
4
5
6
7
8
9
11
10
5
9
Patch regular clock or any other triggers to this input to run and sync sequencer.
Use this input to reset sequence to 1-st step.
This four buttons selects stages and shows active one with light. If CLOCK input is patched, the current active stage will
depends on a sequencer. To adjust stage, hold stage button and rotate knobs on the current active row, or patch off
clock wire, to select active stages without holding.
Tap to activate user sequence (button starts to light with green). If clock is patched, Metamorph will play a factory
programmed sequence now. To programm your own sequence, hold a button for a second. The button starts to flash,
that means you are in program mode. Press stage buttons in oder you wish, the pattern can be really long. Press stage
button several times if you wish to make rests on this stage. After finishing, press SEQ button again, Metamorph will
memorize your sequence and will keep it in memory after power off. To play it, light SEQ button and patch clock to
CLOCK input.
Output trigger pulse each time the stage of the sequence changes.
Outputs +5v while current stage is active.
Tip: patch GATE OUT to REVERSE to make a sequencer run in pendulum mode.
When this input will receive a signal, the direction of the sequencer will change. This input will not work in User
Sequence mode.
Use this input to drive a sequencer and to select active stage with CV. This input accepts voltages from 0 to 5 v. When
CLOCK is patched, the CV input will sync to clock in a sample and hold fashion. This input will not work in User
Sequence mode.
Per channel glide control for sweeping between stages.
CV outputs for each channel. It can ouput voltages in different ranges, selectable with jumpers.
When this input receives signal, the sequencer will stop. To run it again, send gate to RESET IN or press stage select
button.
CLOCK INPUT
RESET
STAGE SELECT BUTTONS
USER SEQUENCE BUTTON
TRIGGERS OUTPUT
STAGE GATE OUTS
REVERSE
CV INPUT
GLIDE
CV OUTPUTS
HOLD
Master
Slave
CH 1CH 2
CH 3
-5v +5v
0v +6v
-2.5v +3.0v
0v +11v
Master
Output voltage jumpers
Master/Slave jumper
Link socket.
Power off your system. Connect dedicated link cable to link sockets on both modules. Set the jumper to “slave” on the
back of one module.
Turn power on. 4 stage buttons on a slave
Important!, both modules need to be powered from one common power bus.
module will lit for a second and then lit off. That means slave founds a master. If 4 lights remain, make sure your
master module is on and press any stage button on slave.
Now you have an eight step sequencer and doubled outputs. However, all inputs and User Sequence button works only
on master module.
Slave
(approximately)
Product specificaties
| Merk: | Dnipro |
| Categorie: | Synthesizer |
| Model: | Metamorph |
Heb je hulp nodig?
Als je hulp nodig hebt met Dnipro Metamorph stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Synthesizer Dnipro
30 December 2025
30 December 2025
Handleiding Synthesizer
- Soma
- Noise Engineering
- Jomox
- Ferrofish
- LennarDigital
- Behringer
- Majella
- Boss
- Arturia
- Erica Synths
- Flame
- Novation
- Casio
- Elektron
- Native
Nieuwste handleidingen voor Synthesizer
10 Juni 2025
4 Juni 2025
16 Mei 2025
13 Mei 2025
13 Mei 2025
12 Mei 2025
12 Mei 2025
12 Mei 2025
1 April 2025
1 April 2025