CRUX CFD-03E Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor CRUX CFD-03E (2 pagina's) in de categorie Achteruitrijcamera. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
- Specially designed for the Ford truck for an OEM look.
- 160 degree wide view angle for excellent visibility.
- Super CMOS technology provides a sharper picture day and night.
PRODUCT FEATURES:
PARTS INCLUDED:
CFD-03E CAMERA BASE EXTENSION CABLE OEM FORD EMBLEM
*NOTE: To power the camera, use RED Wire A or B. If tapping power from the radio or RVC Interface, make sure to
insulate RED Wire A to avoid it from shorng. If you will be tapping power from the reverse light +12V, insulate RED
Wire B to avoid it from shorng. With either connecon the Black GROUND wire needs to be connected to a solid chassis
ground. For vehicles with manual transmission, we recommend tapping +12V power from the reverse light.
PARKING LINES: Unplug the jumper to turn on parking guide lines.
Crux Interfacing Solutions • 6860 Canby Ave., Suite 116, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.052318
CFD-03E
FORD Emblem Camera
for Select Ford Trucks
R
INTERFACING SOLUTIONS
Sightline
CAMERAS
WHITE Wire
Parking Guideline
(see Instructions below)
Regulator
Extension Coax Cable
GROUND
RED Wire (A)*
RED Wire (B)*
Make sure the arrows
line up and push in
the connectors well.
To Aftermarket Radio
Backup Camera Input
OR
Reverse Camera Interface
Backup Camera Input
WIRING DIAGRAM:
1 / 2
VEHICLE APPLICATIONS:
FORD
2004 - 2012 F-150
2008 - 2014 F-250
2008 - 2014 F-350
Crux Interfacing Solutions • 6860 Canby Ave., Suite 116, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.052318
CFD-03E
FORD Emblem Camera
for Select Ford Trucks
R
INTERFACING SOLUTIONS
Sightline
CAMERAS
INSTALLATION PROCEDURE:
1. Remove the Ford Emblem. 2. The OEM holes behind the emblem
will look like this. If your tailgate does
not have these holes, you need to cut
a hole using a drill and the hole saw.
Use a le to smooth out the edges.
3. Some trucks have a hole on the bed
behind the tailgate like on the picture
above. If your truck does not have this
hole, use the hole saw to drill one. Use
a î„®le to smooth the edges.
4. Route the wiring through the tailgate
hole down the opening at the base of
the tailgate.
5. Press in the emblem to cover the
base.
6. Route the harness through the hole
on the truck bed and run it towards the
front of the truck.
Camera Specicaons:
Resoluon: 420 TV Lines
Pixels: 656 x 492
Viewing Angle: 170-degrees
Minimum Illuminaon: 0.2 Lux
Shuer Speed: 1/60s-20us
Voltage: 12V Negave Ground
7. Tap +12V from the reverse light wire
using the supplied 3 î…Ś. power plug or
use the power extension wire built into
the video cable to tap to the reverse
signal wire from an aî…Śermarket radio.
8. To integrate the CFD-03E back-up
camera with the MyFord Touch 8”
screen radio of select 2011-up Ford
vehicles, use part# RVCFD-79 Rear-View
Integraon Kit (not included).
2 / 2


Product specificaties

Merk: CRUX
Categorie: Achteruitrijcamera
Model: CFD-03E

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX CFD-03E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Achteruitrijcamera CRUX

Handleiding Achteruitrijcamera

Nieuwste handleidingen voor Achteruitrijcamera