Crestron CLF-LDIMUEX Handleiding
Bekijk gratis de handleiding van Crestron CLF-LDIMUEX (2 pagina’s), behorend tot de categorie Dimmer. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.2 sterren uit 1.5 reviews. Heb je een vraag over Crestron CLF-LDIMUEX of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
CLF-LDIMUEX
Wireless Lamp Dimmer
Installation and Operation Guide
Important Notes
WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or
fuse and test that the power is off before wiring!
CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO
OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE OR A
TRANSFORMER-SUPPLIED APPLIANCE.
ATTENTION: GRADATEURS COMMANDANT UN BALLAST-AFIN DE REDUIRE LE
RISQUE DE SURCHAUFFE ET LA POSSIBILITE D’ENDOMMAGEMENT A D’AUTRES
MATERIELS, NE PAS INSTALLER POUR COMMANDER UNE PRISE OU UN APPAREIL
ALIMENTE PAR UN TRANSFORMATEUR.
NOTES: Observe the following points:
• Install and use the CLF-LDIMUEX in accordance with appropriate electrical codes
and regulations.
• Use the dimmer where temperatures are between 32°F and 104°F (0°C and 40°C).
NOTE: Record the serial number of the device before installation. Refer to inNET EX
Important Notice (Doc. 7179) included in the box.
The device must remain in an accessible location when placed into Acquire mode and
joined to a gateway.
Description
The Crestron
®
CLF-LDIMUEX is a universal lamp dimmer capable of dimming most
120 Vac lighting loads, such as those commonly found with table and oor lamps.
Powered by inNET EX
®
technology, this device communicates wirelessly with the control
system, making it perfect for both new and retrot applications. CLF-LDIMUEX lets you
control any lamp from a touch screen, keypad, on-screen display, or other Crestron
remote control device. For complete in-sync control, the CLF-LDIMUEX also connects
directly to the switch located on the lamp.
CLF-LDIMUEX Specications
Wiring
Typical Wiring Diagram
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates. Use a QR
reader application on your mobile device to scan the QR image.
NOTE: The contact closure does not need to be connected for proper operation.
Remote Switch Wiring Options
Standard Lamp Wiring
Installation
WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or
fuse and test that the power is off before wiring!
NOTE: A licensed electrician must install the dimmer.
NOTE: Before using the CLF-LDIMUEX, ensure the device is using the latest rmware.
Check for the latest rmware for the CLF-LDIMUEX at www.crestron.com/rmware.
Firmware is loaded onto the device using Crestron Toolbox™.
Complete the following procedure to install a CLF-LDIMUEX dimmer:
1. Connect the lamp to the female 2-pin polarized NEMA1-15R connector of the
CLF-LDIMUEX.
2. Connect the contact closure from the lamp to the female C7 connector of the
dimmer (optional).
3. Plug the male 2-pin polarized NEMA1-15P cord of the dimmer to a standard
120 V power outlet.
CAUTION: The CLF-LDIMUEX should be placed in a well-ventilated and dry area.
CLF-LDIMUEX Wiring with Contact Closure
CLF-LDIMUEX
1 ft
(~.30 m)
5 ft
(~1.5 m)
Local and Remote Operation
The operation described in this guide assumes the CLF-LDIMUEX is in Local mode, where
the external slave-switch (sold separately) directly controls the light levels on the dimmer.
The device can also operate in Remote mode, where the external slave-switch sends
commands to the control system and the commands are then routed to control the load.
Local mode options (available in SIMPL Windows):
• Maintained Switch (Default): The unit toggles on and off when the slave-switch is
toggled.
• Momentary Switch:
> Single Tap - Toggles the load on and off.
> Double Tap - Initiates a fast-full-on.
> Hold - Initiates cycle dimming.
SPECIFICATION DETAILS
Input Voltage 120 Vac, 60 Hz, line power
Load Ratings
Number of Channels 1
Maximum Load per
Channel
250 W/250 VA
Load Types Incandescent, tungsten-halogen, magnetic low-
voltage, electronic low-voltage, LED, dimmable CFL
Environmental
Temperature 32°F to 104°F (0°C to40 °C )
Humidity 10% to 90% RH (noncondensing)
Wireless Communications
The device connects to the Crestron network via the inNET EX communications protocol.
Use the procedures outlined below to join or leave an inNET EX network and to verify
communications between the device and the control system.
Joining an inNET EX Network
Before a device can be used in a lighting system, it must rst join an inNET EX network.
To join an inNET EX network, the device must be acquired by an inNET EX gateway.
NOTE: A device can be acquired by only one gateway.
1. Put the inNET EX gateway into Acquire mode from the unit itself or from Crestron
Toolbox. Refer to the gateway’s manual at www.crestron.com/manuals for details.
NOTE: In an environment where multiple gateways are installed, only one
gateway should be in Acquire mode at any time.
2. Put the device into Acquire mode.
a. Tap the Setup button on the device three times, and then press and hold it down
(tap-tap-tap-press+hold) until the On and Off LEDs blink once (this can take up to
10 seconds).
b. Release the Setup button to start the acquire process. The On LED and the
attached load blink slowly to show that the device is actively scanning the inNET
EX network.
NOTE: The acquire process can also be initiated by a remote maintained
switch (if equipped) by ipping the switch four times rapidly or by tapping the
remote momentary switch (if equipped) four times rapidly. The On LED and
attached load will blink (this can take up to 10 seconds).
• The On LED and attached load turn on for 5 seconds to show that the device
has been successfully acquired by the infiNET EX network.
• The On LED and attached load blink fast to indicate that the device was not
successfully acquired by the infiNET EX network. Tap the button to
acknowledge the failure. Ensure the gateway is in Acquire mode and within
range before attempting the acquire process again.
3. Once all devices have been acquired, take the gateway out of Acquire mode. Refer
to the gateway’s manual for details.
Leaving an inNET EX Network
To leave an inNET EX network, put the device into Acquire mode, as described in
“Joining an inNET EX Network” above, when no gateway is in Acquire mode.
Verifying Communications Status
To check the communications status of the device, tap the Setup button three times and
then press and hold it down (tap-tap-tap-press+hold) for up to 2 seconds. The LED blinks
to indicate the communications status. Refer to the following table for details.
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more if the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Crestron Electronics, Inc. Installation & Operation Guide - DOC. 7285B
15 Volvo Drive Rockleigh, NJ 07647 (2032222)
Tel: 888.CRESTRON 11.15
Fax: 201.767.7576 Specications subject to
www.crestron.com change without notice.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie
Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
To satisfy RF exposure requirements, this device and its antenna must operate with a separation
distance of at least 20 centimeters from all persons and must not be colocated or operating in
conjunction with any other antenna or transmitter.
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, inNET EX, and the inNET EX logo are either
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the marks and
names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
Troubleshooting
The following table provides corrective actions for possible trouble situations. If further
assistance is required, please contact a Crestron customer service representative.
CLF-LDIMUEX Troubleshooting
TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION
The device does
not function.
The dimmer is not
receiving power.
Verify that the dimmer is properly
connected to the power line and
neutral. Verify that the circuit
breaker is closed.
The dimmer is in Remote
mode.
Check the program to determine or
change the operating mode.
The dimmer is not
communicating with the
network.
Use the Crestron Toolbox to poll
the network. Verify the network
connection to the device.
LED COMMUNICATIONS STATUS
Turns on for 5 seconds The device is communicating with the control system.
Blinks three times The device is communicating with the gateway, but the
gateway is not communicating with the control system.
Blinks twice The device was previously joined to the network but is
not communicating with the gateway.
Blinks once The device is not joined to the network.
Product specificaties
| Merk: | Crestron |
| Categorie: | Dimmer |
| Model: | CLF-LDIMUEX |
Heb je hulp nodig?
Als je hulp nodig hebt met Crestron CLF-LDIMUEX stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Dimmer Crestron
13 Mei 2025
13 Mei 2025
1 April 2025
1 April 2025
11 Maart 2025
11 Maart 2025
11 Maart 2025
11 Maart 2025
11 Maart 2025
11 Maart 2025
Handleiding Dimmer
- Hager
- Eminent
- Trust
- Paladin
- Legrand
- Mercury
- Merten
- TP Link
- Arendo
- Jung
- Steinel
- Berker
- InterBar
- GAO
- Tradim
Nieuwste handleidingen voor Dimmer
28 Maart 2025
28 Maart 2025
2 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024
1 December 2024