Comark C12 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Comark C12 (6 pagina's) in de categorie Thermometer. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
Description
C series thermometers have a high strength, polycarbonate
case with rubber over moulding to provide durability and
protection against dust and water ingress
The Catercheck 3 is based on the C20 but has a xed probe.
C12 HACCP Thermometer
The C12 Thermometer comes complete with colour coded
labels so that you can change the colour from blue to red,
green, yellow or orange.
Instructions
Should you wish to change the blue label on your C12
thermometer from the blue label supplied, remove the plastic
protective cover from the C12 Label at the front of the
instrument (if tted). It is not necessary to remove the label
itself. Select the new coloured label and carefully remove the
backing cover to reveal the glued area. Carefully align the
label over the old one and ax into place.
The air and penetration probes provided do not have colour
coding.
1
Overview of Display Symbols
A – Main Display for Temperature
B – °C Indicat or
C – – Sensor Type PST (Thermistor)
D – Low Battery Indicator
Connecting Probes to the Thermometers
The C12 and C20 thermometer have sockets for probe
connection of Thermistor probes.
Switching On and O
The single ‘ON/OFF’ button on the keypad is used to switch
on the thermometer. After a short pause the display will show
the model of the instrument and will then revert to normal
temperature display.
2
Comark Handheld Thermometers
C12 HACCP ,
C20 and Catercheck 3
Operator Manual
Auto Switch O/Power Saving Mode
C12 and C20 series thermometers have auto-switch o
feature. This is set to 3 minutes.
Care of the Thermometer
C12 and C20 series thermometers are dust and waterproof as
stated in the specications and will withstand harsh
environments. Use a damp cloth or warm soapy water to
remove deposits and prevent them from hardening or
becoming sticky. Do not use solvent-based cleaners or
methylated spirit, etc.
C20
In particularly harsh environments care should be taken to
clean the Lumberg probe connector regularly. This should
ensure it does not become dicult to remove the probe from
the thermometer. The probe should be removed from the
instrument as frequently as necessary, the thread then
cleaned and lubricated with food safe oil.
Caution: Do not place any C12 or C20 series thermometers in
a dishwasher.
Changing the Batteries
The symbol BAT appears on the display when the battery
voltage has reduced. Battery replacement is recommended at
this time.
To replace the battery, remove the battery cover retaining
screw on the rear of the instrument, using the correct size
screwdriver. Remove the two cells, and replace with alkaline
cells only. Be careful to observe the correct polarity. Take
care not to over-tighten the screw when retting the cover.
Note: The C12 and C20 series thermometers will not work if
the battery compartment is incorrectly tted or missing. In this
instance the display will show ‘OPEn’. Please note the small
pip on the inside of the battery cover, which must t into the
hole provided in the back of the case.
3
Trim folded width to
63mm
Specications for C12, C20 and Catercheck 3
Sensor Thermistor 10 K Ohms uni-curve
Connector : 3.5mm Jack C12
C20: 6-pin Lumberg
Measurement Range -40°C to +125°C
Scale °C
Displayed Resolution 0.1°
System Accuracy at 23°C ±0.5°C -20°C to +70°C
Ambient Temperature Range -20°C to +50°C operating
Display 4 digit 12.5 mm LCD
Battery Two of type I.E.C. LR6 Size AA
Battery Life (continuous) up to 14000 Hours
Environmental Protection
C20 Certied IP67, BS 60529, IEC 529
Catercheck 3 Not Certied
C12 Not Certied
EMC Emission Tested to EN61326-1
Criteria B Performance
Dimensions (Excluding Probe)
Length 152mm/6 inches
Width 58mm/2.3 inches
Depth 22/27mm/0.9/1.1 inches
Weight 178g/6.3 ozs
4
Description
Les thermomÚtres série C ont un boßtier en polycarbonate
haute résistance avec surmoulage, pour garantir la durabilité
et orir une protection contre la pĂ©nĂ©tration de poussiĂšre et
d'eau
Le Catercheck 3 est articulé sur le C20, mais a une sonde
xe.
C12 HACCP ThermomĂštre
Le thermomÚtre C12 est livré avec étiquettes couleur codées
de sorte que vous pouvez changer la couleur du bleu au
rouge, vert, jaune ou orange.
Instructions
Si vous souhaitez modier l'Ă©tiquette bleue sur votre
thermomĂštre C12 Ă  partir de l'Ă©tiquette bleue fournie, retirez
le couvercle de protection en plastique de l'Ă©tiquette C12 Ă 
l'avant de l'appareil (le cas échéant). Il n'est pas nécessaire
d'enlever l'Ă©tiquette elle-mĂȘme. SĂ©lectionnez la nouvelle
étiquette de couleur et retirez avec précaution le couvercle du
support de révéler la zone collée. Alignez soigneusement
l'Ă©tiquette sur l'ancienne et xez en place.
Les sondes d'air et la pénétration prévus n'ont pas un code
de couleur.
6
ThermomĂštres portables Comark
Gamme HACCP C12 ,
C20 et Catercheck 3
Manuel de l'utilisateur
5
PrĂ©sentation des symboles de l'acheur
A – Achage principal de la tempĂ©rature
B – Indicateur en °C
C – – Type de capteur PST (Thermistor)
D – Indicateur de faible autonomie
Raccordement des sondes aux thermomĂštres
Les thermomÚtres C12 et C20 ont des prises réservées au
raccordement des sondes Ă  thermistor.
Mise sous tension et hors tension
Le bouton « ON/OFF » (marche/arrĂȘt) unique du clavier
permet d'allumer le thermomĂštre. AprĂšs une brĂšve pause,
l'acheur indique le modùle de l'instrument, puis revient à
l'achage normal de la tempĂ©rature.
7
Caractéristiques des C12, C20 et Catercheck 3
Capteur Thermistor 10 KOhms uni-curve
Connecteur : Jack 3,5 C12 mm
: Lumberg 6 broches C20
Gamme de mesure -40°C à +125°C
Echelle °C
RĂ©solution achĂ©e 0,1°
Précision du systÚme à 23°C ±0,5°C -20°C à +70°C
Gamme de température ambiante -20°C à +50°C en fonctionnement
Acheur LCD 4 chires, 12,5 mm
Piles Deux de type I.E.C. LR6 Size AA
Autonomie des piles
(utilisation continue) jusqu'Ă  14 000 h eures
Protection environnementale
C20 Certié IP67, BS 60529, IEC 529
Catercheck 3 Non certié
C12 Non certié
Emissions EMC Testé selon EN61326-1
Performances critĂšre B
Dimensions (hors sonde)
Longueur 152 mm / 6 pouces
Longueur 58 mm / 2,3 pouces
Profondeur 22/27 mm / 0,9/1,1 pouce
Poids g / 6,3 onces 178
9
Mode ArrĂȘt automatique/Economie d'Ă©nergie
Les thermomÚtres série C12 et C20 comportent une fonction
d'arrĂȘt automatique programmable. Elle est rĂ©glĂ©e sur 3
minutes.
Entretien du thermomĂštre
Les thermomÚtres série C12 et C20 résistent à l'eau et à la
poussiÚre comme indiqué dans les caractéristiques et sont
adaptĂ©s aux environnements diciles. Utilisez un chion
humide ou une solution d'eau savonneuse chaude pour
enlever les dĂ©pĂŽts et les empĂȘcher de durcir ou devenir
collants. N'utilisez pas de nettoyants Ă  base de solvants ou
d'alcool méthylique, etc.
C20
Dans les environnements particuliùrement diciles, il faut
veiller à nettoyer réguliÚrement le connecteur de sonde
Lumberg. Cela permet d'Ă©viter que le retrait de la sonde du
thermomùtre ne devienne dicile. Il faut retirer la sonde de
l'instrument aussi fréquemment que nécessaire, puis nettoyer
le letage et le lubrier avec de l'huile adaptĂ©e au contact
alimentaire.
Attention : ne placez jamais un thermomÚtre série C12 ou
C20 au lave-vaisselle.
Remplacement des piles
Le symbole BAT s'ache lorsque la tension des piles faiblit.
Un remplacement est alors conseillé.
Pour remplacer les piles, retirez la vis de xation du couvercle
du compartiment située à l'arriÚre de l'instrument, avec un
tournevis de taille correcte. Retirez les deux piles et
remplacez-les par des piles alcaline uniquement. Veillez Ă 
respecter la polarité. Prenez soin de ne pas trop serrer la vis
en remettant le couvercle en place.
Remar : les thermomÚtres série C12 et C20 ne que
fonctionnent pas si le compartiment des piles est mal xĂ© ou
absent. L'acheur indique alors « OPEn ». Veuillez noter la
petite pointe sur l'intérieur du couvercle du compartiment, qui
doit entrer dans l'encoche prévue à l'arriÚre du boßtier.
8
Beschreibung
Die Thermometer der Reihen C haben ein Ă€ußerst robustes
GehÀuse aus Polykarbonat mit Gummierung, das eine lange
Haltbarkeit bietet und vor dem Eindringen von Staub und
Wasser schĂŒtzt.
Der Catercheck 3 basiert auf dem C20, verfĂŒgt jedoch ĂŒber
einen festen MessfĂŒhler.
C11 HACCP-Thermometer
Der C12 Thermometer wird komplett mit farbigen Etiketten, so
dass Sie die Farbe von blau zu rot, grĂŒn, gelb oder orange
Àndern können.
Anleitung
Sollten Sie das blaue Etikett auf Ihrem C12 Thermometer
Ă€ndern aus dem blauen Label geliefert, entfernen Sie die
Kunststo-Schutzkappe von der C12 Label auf der
Vorderseite des GerÀtes (falls vorhanden). Es ist nicht
notwendig, um das Etikett selbst zu entfernen. WĂ€hlen Sie
den neuen farbigen Aufkleber und entfernen Sie vorsichtig die
Schutzfolie Abdeckung, um die Klebeî‹•Ă€che zu oenbaren.
Richten Sie das Etikett ĂŒber die alte und kleben an seinen
Platz.
Die Luft-und EinstechfĂŒhler vorgesehen habe keine
Farbcodierung..
11
Handthermometer von Comark
C12 HACCP-Bereich,
C20 und Catercheck 3
Bedienerhandbuch
10


Product specificaties

Merk: Comark
Categorie: Thermometer
Model: C12

Heb je hulp nodig?

Als je hulp nodig hebt met Comark C12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Thermometer Comark

Handleiding Thermometer

Nieuwste handleidingen voor Thermometer