Chamberlain 041-0181-000 Handleiding

Bekijk gratis de handleiding van Chamberlain 041-0181-000 (27 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 37 mensen en kreeg gemiddeld 4.0 sterren uit 8 reviews. Heb je een vraag over Chamberlain 041-0181-000 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Wire Harness Replacement

Repair Parts 041-0180-000, 041-0181-000

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Introduction

Use this instruction to replace the integrated LED light module cover. The

images throughout this manual are for reference only and your product may

look different.

You will need:

• 1/4" magnetic nut driver

• Long-nosed pliers

• 5/16" long-shafted magnetic nut driver and socket

• Flathead screwdriver

Instructions

The images throughout this manual are for reference only and your product

may look different.

1. Disconnect the electrical and battery power (if applicable) to the garage

door opener. Remove the battery and place in a safe location.

2. Remove the control door panel from both ends of the opener.

Refer to . Figure 1

a. Squeeze or separate

hinges depending on the

style of operator.

b. Remove the control door

panel from the hinge

setting, and place in a

safe location.

3. Disconnect the door control

wires from the RED and

WHITE terminals and the

Safety Reversal Sensor wires

from the BLACK and WHITE

terminals. . Figure 2

4. Remove the end panels from

both ends of the opener.

5. Remove decorative ring

from opener (applicable

units). .Figure 3

6. Remove the integrated LED

light module cover from the

opener. .Figure 4

7. Disconnect the ORANGE and

WHITE wire harness from

plug to the Integrated LED

light module and set aside cover / integrated LED light module. Figure 4

(A).

8. Remove the wire harness:

a. Unplug the 4-wire harness (ORANGE, BLACK, WHITE, GREEN) from the

receiver logic board. .Figure 4 (B)

b. Unplug the WHITE and BLACK wires from the terminal block.

Refer to .Figure 5

c. Remove the GREEN

ground wire.

8. Attach the new wire harness.

a. Attach the ORANGE and

WHITE wire harness from

plug to the integrated LED

light module.

b. Attach the GREEN

ground wire.

c. Plug in the 4-wire harness

(ORANGE, BLACK, WHITE,

GREEN) from the receiver

logic board. . Figure 3 (B)

d. Plug in the WHITE and

BLACK wires from the

terminal block.

e. Bundle and fasten the wires

together with a wire tie.

9. Attach integrated LED light

module.

10. Attach both end panels.

11. Attach decorative ring (applicable units).

12. Reconnect the door control and Safety Reversal Sensor wires. . Figure 2

Door control:

• WHITE wire into the WHITE terminal.

• WHITE/RED wire into the RED terminal.

Safety Reversal Sensors:

• WHITE wires into the WHITE terminal.

• WHITE/BLACK wires into the GRAY terminal.

13. Reattach the control door panels.

14. Reconnect power to the opener.

15. Test the Safety Reversal System. Refer to the Owner’s Manual.

RED

WHITE

WHITE

GREY

Figure 2

Figure 3

Figure 1

A

B

Figure 4

Figure 5

Integrated LED Light Module

Control Door Panel

End Panel

Terminal

Block

Black

Wire

White

Wire

Terminal

Block

Product specificaties