Casio EQS-500DB-1A1 Handleiding

Casio Horloge EQS-500DB-1A1

Bekijk gratis de handleiding van Casio EQS-500DB-1A1 (4 pagina’s), behorend tot de categorie Horloge. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.6 sterren uit 7 reviews. Heb je een vraag over Casio EQS-500DB-1A1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/4

Operation Guide 5123

MA1004-EA

Congratulations upon your selection of this CASIO watch.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours for Newfoundland, Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage

or loss suffered by you or any third party arising through the use of this product or

its malfunction.

About This Manual

Button operations are indicated using the letters A through

D shown in the illustration.

Hand Functions

z Hour Hand

x Second Hand

c Minute Hand

v Upper Left Dial Hand

b Lower Left Dial Hands

n Right Dial Hand: Indicates the current mode.

m Day

This User’s Guide uses numbers shown above to identify

watch hands and indicators.

Things to check before using the watch

1. Hold down C for about two seconds to enter the Timekeeping Mode, and

then observe the movement of the

x Second Hand.

Is the x Second Hand moving smoothly at one-second intervals?

Is the x Second Hand moving at

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged sufﬁciently.

For details about charging, see

“Charging the Watch”.

Power is low. Charge the watch by placing

it in a location where it is exposed to light.

For details, see “Charging the Watch”.

YES

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁgure Home City settings” to conﬁgure your Home

City and daylight saving time settings.

Important!

World Time settings depend on correct Home City, time, and date settings in the

Timekeeping Mode. Make sure these settings are conﬁgured correctly.

3. Set the current time.

See “Conﬁguring Current Time and Date Settings”.

The watch is now ready for use.

Charging the Watch

The face of the watch is a solar cell that generates power from light. The generated

power charges a built-in rechargeable battery, which powers watch operations. The

watch charges whenever it is exposed to light.

Charging Guide

Whenever you are not

wearing the watch, be sure

to leave it in a location

where it is exposed to light.

Best charging •

performance is achieved

by exposing the watch to

light that is as strong as

possible.

When wearing the watch,

makes sure that its face is

not blocked from light by the

sleeve of your clothing.

The watch may enter a •

sleep state if its face is

blocked by your sleeve

even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become

particularly hot when exposed to the following conditions for long periods.

On the dashboard of a car parked in direct sunlight •

Too close to an incandescent lamp •

Under direct sunlight •

Important!

Keep the watch in an area normally exposed to bright light when storing it for long •

periods. This helps to ensure that power does not run down.

Storing the watch for long periods in an area where there is no light or wearing it in •

such a way that it is blocked from exposure to light can cause power to run down.

Make sure that the watch is exposed to bright light whenever possible.



B +

*> 6 5

Power Levels

You can get an idea of the watch’s power level by

observing the movement of the

x Second Hand in the

Timekeeping Mode.

If the •

x Second Hand is moving normally at one-second

intervals, power is at Level 1.

If the •

x Second Hand is moving at two-second intervals,

power is at Level 2, which is quite low. Expose the watch

to light as soon as possible so it can charge.

Moving at two-second

intervals.

B +

Level Hand Movement Function Status

1 Normal. All functions enabled.

x Second Hand moving at two-second

intervals.

m Day changes to 1 (home position).

Beeper disabled.

x Second Hand stopped.

z Hour Hand and c Minute Hand stopped

at 12 o’clock.

All functions disabled.

When power drops to Level 3, all functions will be disabled but the watch will •

continue to keep time internally for about one week. If you recharge the battery

sufﬁciently during this period, the analog hands will move automatically to the

correct setting and regular timekeeping will resume. After one week, all settings

(including timekeeping) will be cleared. Recharging the battery will reset all settings

to their initial factory defaults.

Power Recovery Mode

The watch is designed to go into a power recovery mode that stops hand operation

temporarily whenever power suddenly drops below a certain level due to overuse

of the alarm tone over a short period. Note that all operations are disabled while the

watch is in the power recovery mode.

The hands will move to the correct positions and the watch will resume normal

operation after power recovers (in about 15 minutes). Putting the watch in a location

where it is exposed to light will help power to recover sooner.

Charging Times

Exposure Level (Brightness)

Daily

Operation *1

Level Change *2

Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 minutes 2 hours 27 hours

Window sunlight (10,000 lux) 30 minutes 6 hours 100 hours

Window sunlight on cloudy day

(5,000 lux)

48 minutes 10 hours – – –

Indoor ﬂuorescent lighting (500 lux) 8 hours 112 hours – – –

1 Approximate exposure each day to generate power for normal daily operation. *

2 Approximate exposure to take power up one level. *

The above exposure times all are for reference only. Actual exposure times depend •

on lighting conditions.

For details about the operating time and daily operating conditions, see the “Power •

Supply” section of the Speciﬁcations.

Power Saving

Power Saving enters a sleep state automatically whenever the watch is left for a

certain period in an area where it is dark. The table below shows how watch functions

are affected by Power Saving.

There actually are two sleep state levels: “second hand sleep” and “function sleep”. •

Elapsed Time in Dark Operation

60 to 70 minutes (second hand

sleep)

x Second Hand only is stopped at 12 o’clock, all other

functions are enabled.

6 or 7 days (function sleep)

All functions, including analog timekeeping, disabled •

Internal timekeeping maintained. •

The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch •

is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep

state.

The watch will not enter a sleep state while it is in the Stopwatch Mode. •

To recover from the sleep state

Move the watch to a well-lit area or press any button.

Mode Reference Guide

Your watch has four “modes”. The mode you should select depends on what you

want to do.

To do this: Enter this mode:

View the current time in your Home City and in one of 29 •

cities around the globe

Conﬁgure Home City and daylight saving time (DST) •

settings

Conﬁgure time and date settings •

Timekeeping Mode

Use the stopwatch to measure elapsed time Stopwatch Mode

View the current time in one of 29 cities (time zones) around

the globe

World Time Mode

Set an alarm time Alarm Mode

Selecting a Mode

With this watch, everything starts from the Timekeeping Mode.

To determine the watch’s current mode

Check the position of the

n Right Dial Hand as shown

under “To select a mode”.

To return to the Timekeeping Mode from any other

mode

Hold down C for about two seconds until the watch beeps

twice.



Operation Guide 5123

To select a mode

Press C to cycle between the modes as shown below. The

n Right Dial Hand

indicates the currently selected mode.

Timekeeping Mode Stopwatch Mode

Alarm Mode World Time Mode

The short end of the

hand indicates the

day of the week.

The hand points to 0.

The hand points to ALM. The hand points to STD

or DST.

Timekeeping

Use the Timekeeping Mode to view the current time and date. To enter the

Timekeeping Mode from any other mode, hold down C for about two seconds.

Hand Functions

z Hour Hand

x Second Hand

c Minute Hand

v Upper Left Dial Hand:

Indicates the current hour in the Home City time in

24-hour format.

b Lower Left Dial Hands:

Indicate the current time in the World Time City in

24-hour format.

n Right Dial Hand: The short end of the hand indicates

the day of the week.

m Day

Conﬁguring Home City Settings

There are two Home City settings: actually selecting the Home City and selecting

either standard time or daylight saving time (DST).

To conﬁgure Home City settings

Note

This watch does not have a city code that corresponds •

to Newfoundland.

In the Timekeeping Mode, keep 1. A depressed (for about

ﬁve seconds) as the

x Second Hand moves to the city

code of the currently selected Home City.

This indicates the city code setting mode. •

The watch will exit the setting mode automatically if •

you do not perform any operation for about two or

three minutes.

For details about city codes, see the “City Code •

Table”.

To change the Home City setting, press 2. D to move the

x Second Hand clockwise.

Keep pressing • D until the

x Second Hand is pointing

at the city code you want to select as your Home City.

Each time you select a city code, the •

z Hour Hand,

c Minute Hand, v Upper Left Dial Hand and m Day

move to the current time and date for that city code.

Do not perform the next operation until these hands

stop moving.

Press 3. B to toggle the time for the currently selected

city code between STD (standard time)/DST (daylight

saving time).

In the city code setting mode, the •

n Right Dial Hand indicates the current

daylight saving time setting as STD (standard time) or DST (daylight saving

time).

Note that you cannot switch between • STD (standard time)/DST (daylight saving

time) while UTC is selected as your Home City.

After the setting is the way you want, press 4. A to return to the Timekeeping Mode.

To toggle the Home City time between standard time and daylight saving time

Perform the step 1 under “To conﬁgure Home City settings”.1.

Each time you select a city code, the •

z Hour Hand, c Minute Hand, and

v Upper Left Dial Hand move to the current time for that city code. Do not

perform the next operation until these hands stop moving.

Press 2. B to toggle the time for the city code of the currently selected Home City

between STD (standard time)/DST (daylight saving time).

In the city code setting mode, the •

n Right Dial Hand indicates the current

daylight saving time setting as STD (standard time) or DST (daylight saving

time).

Note that you cannot switch between • STD (standard time)/DST (daylight saving

time) while UTC is selected as your Home City.

After the setting is the way you want, press 3. A to return to the Timekeeping Mode.

Note

After you specify a city code, the watch will use UTC* offsets in the World Time •

Mode to calculate the current time for other time zones based on the current time

in your Home City.

Coordinated Universal Time, the world-wide scientiﬁc standard of timekeeping. The *

reference point for UTC is Greenwich, England.



B +

*> 6 5



B +

> @ 6 5

Conﬁguring Current Time and Date Settings

You can conﬁgure current time and date settings.

To change the current time setting

In the Timekeeping Mode, keep 1. A depressed (for about

ﬁve seconds) as the

x Second Hand moves to the city

code of the currently selected Home City.

At this time, the •

n Right Dial Hand will indicate the

Home City’s current daylight saving time setting (STD

or DST).

Change the Home City and daylight saving time (DST) 2.

settings, if you want.

For details about these settings, see steps 2 and 3 •

under “To conﬁgure Home City settings”.

In the following steps, each press of • C cycles

between settings as shown below.

Home city/DST Hour/Minute Year (tens digit)

Year (ones digit)

Day Month

Press 3. C.

The watch will beep, and the •

x Second Hand and n Right Dial Hand will move

to their 12 o’clock positions. This is the time setting mode.

Use 4. D (+) and B (–) to change the time (hour and minute) setting.

Each press of either button will move the hands ( •

z Hour Hand and c Minute

Hand) one minute.

Holding down • D or B will start high-speed

z Hour Hand and c Minute Hand

movement in the applicable direction. To stop high-speed hand movement,

press any button.

The •

v Upper Left Dial Hand and z Hour Hand move in sync with each other.

When setting the time, make sure that the •

v Upper Left Dial Hand indicates the

proper a.m./p.m. hour.

If you want to change the date setting at this time, press • C and perform the

procedure starting from step 3 under “To change the current date setting”.

After the time setting is the way you want, press 5. A to return to the Timekeeping

Mode.

This will cause the •

x Second Hand to move automatically to 12 o’clock and

resume movement from there.

To change the current date setting

In the Timekeeping Mode, keep 1. A depressed (for about ﬁve seconds) as the

Second Hand moves to the city code of the currently selected Home City.

Press 2. C twice.

The watch will beep and change to the year setting mode. •

The year can be set in the range of 2000 to 2099. •

You can save your settings and exit the setting procedure at any time by •

pressing A, which will return to the Timekeeping Mode. This will cause the

Second Hand to move automatically to 12 o’clock and resume normal movement

from there.

Use 3. D to change the tens digit of the year

setting.

Each press of • D will move the

x Second

Hand and change the tens digit of the year

setting.

After the tens digit of the year setting is the way 4.

you want, press C.

The watch will beep and change to the ones •

digit of the year setting mode.



B +

Setting the year (tens digit)

Use 5. D to change the ones digit of the year

setting.

Each press of • D will move the

x Second

Hand and change the ones digit of the year

setting.

After the ones digit of the year setting is the way 6.

you want, press C.

The watch will beep and change to the month •

setting mode.

Setting the year (ones digit)

Use 7. D to move the x Second Hand to the

month setting you want.

After the month setting is the way you want, 8.

press C.

The watch will beep and change to the day •

setting mode.

Setting the month

Dec

Jun

Jan

Apr

Feb

Mar

Jul

Sep

Aug

May

Oct

Nov

Product specificaties

Merk:	Casio
Categorie:	Horloge
Model:	EQS-500DB-1A1
Gewicht:	164 g
Breedte:	50 mm
Diepte:	45.8 mm
Hoogte:	12.3 mm
Type horloge:	Armbandhorloge
Mechanismetype:	Kwarts (zonne-energie)
Chronograaf:	Ja
Type wijzerplaat horloge:	Analoge wijzerplaat
Waterdicht:	Ja
Stopwatch:	Ja
Waterbestendig diepte:	100 m
Wereldklok functie:	Ja
Alarm functie:	Ja
Agenda:	Ja
Snooze functie:	Ja
Klokmodus:	24 uur
Nauwkeurigheid:	15 sec/maand
Type kalender:	Datum
Horlogekast materiaal:	Roestvrijstaal
Kleur behuizing:	Roestvrijstaal
Band materiaal:	Roestvrijstaal
Hoofdkleur van band:	Roestvrijstaal
Glas type van horloge:	Mineraalglas
Hoesvorm:	Rond
Hoofdkleur van wijzerplaat:	Zwart
Geslacht:	Man
Stijl becijfering horloge:	Arabische cijfers/geen cijfers