Canarm GSQ135-D Handleiding
Canarm
Ventilator
GSQ135-D
Lees hieronder de 📖 handleiding in het Nederlandse voor Canarm GSQ135-D (10 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 2 personen en werd door 1.5 gebruikers gemiddeld met 3.8 sterren beoordeeld
Pagina 1/10
GSQ-D SERIES
GSQ-D EC SERIES
DIRECT DRIVE GALVANIZED SQUARE INLINE BLOWER
OPERATION INSTRUCTIONS AND MANUAL      PARTS 
PLEASE READ AND SAVE THESE INSTRUCTIONS
M_GSQ_D_06_16_2022 Page 1 of 5
GENERAL SAFETY
GSQ-D SERIES MODELS: GSQ105-D, GSQ120-D, GSQ135-D, GSQ150-D, GSQ165-D, GSQ180-D
1. All electrical work must be done in accordance with all applicable electrical codes by a qualified electrician.
2. Prior to wiring ensure the power supply is locked in the position and that the motor nameplate voltage matches the supply OFF
voltage.
3. Do not install or operate this fan in an environment where combustible materials, gases or fumes are present.
4. the fan contains rotating parts and electrical service. Appropriate safety precautions should be taken during installation, Caution:
operation and maintenance.
5. Before starting the unit, ensure the wheel rotates freely.
6. Check and tighten where necessary all nuts, bolts & set screws prior to fan start up (as some may have loosened during shipment).
7. Please follow all applicable national, state/provincial and local codes, all of them will supersede this manual.
8. Failure to follow the safety instructions in this manual may cause serious injury or death due to electrical shock or high
speed rotating parts.
The purpose of this manual is to aid in the proper installation and operation of the blowers. These instructions are intended to supplement
good general practices and are not intended to cover detailed instruction procedures.
IT IS THE RESPONSIBILITY OF THE PURCHASER TO ENSURE THAT THE INSTALLATION AND MAINTENANCE OF THIS
EQUIPMENT IS HANDLED BY QUALIFIED PERSONNEL.
Inspect all shipments carefully for damage. THE RECEIVER MUST NOTE ANY DAMAGE ON THE CARRIER’S BILL OF LADING
AND FILE A CLAIM IMMEDIATELY WITH THE FREIGHT COMPANY.
GSQ-D SERIES
GSQ-D EC SERIES
DIMENSIONS
INSTALLATION
Suspension mounting: move the mounting brackets to desired
corners using the hardware provided, secure the unit to 4 customer
provided suspension rods.
Base mounting: move the mounting brackets to desired corners
using the hardware provided, secure the unit to the base. Vibration
isolators (available as accessory) are recommended for both
suspension and base mount to provide quiet operation.
In order to change the direction of discharge, relocate the access
door to leave desir
ed direction open.
M_GSQ_D_06_16_2022 Page 2 of 5
!"#$% & ' &( '( )
*+,-.-/#/$0 !"#"$%&' !!#"$%&' !(#)*$%& !! !"#*$!%'
*+,(-1/#/$0 !*#!$(' !&#"$(' +!#!$+' !"#)$(' !(#!"$!%'
*+,(2-/#/$0 +,' !*' +&#)$(' !*#)$&' +!#!)$!%'
*+,(31/#/$0 ++' !(#)$&' +%#)$(' !-#!$+' +)#!)$!%'
*+,(1-/#/$0 +&#!$+' +,#*$(' )(#)$(' +!#"$(' +%#"$!%'
*+,(41/#/$0 +%#)$&' +)' )!#!$(' +)#)$&' +(#-$!%'
*+,(5-/#/$0 +-#"$(' +"#)$(' )&' +%#!$(' )!#*$!%'
*+,/#/$06#78$096#87:$6'&0;<&8#67=0%7=$#6+,>&8$67=%7=$6'%"<$8
A1
B1
A A
A
B
B
The 8 brackets provided in parts bag could accommodate different
mounting direction/style, either base or suspension mounting.
GSQ-D SERIES
GSQ-D EC SERIES
STANDARD WIRING INSTRUCTIONS
M_GSQ_D_06_16_2022 Page 3 of 5
1. A qualified electrician in accordance with all local and National Electrical Codes should do all wiring.
2. Ensure power supply is disconnected and locked out prior to making electrical connections.
3. Excess wire must be restrained in order to prevent it from entering the pulley, shaft or wheel rotating area.
4. Disconnect switches are recommended and should be located near the fan in order to, swiftly cut off power in case of an emergency
and maintain complete control of the power source.
5. Follow the wiring diagram on the motor nameplate.
Power is connected to the motor and control module through the junction box and wiring harness provided.
Note: For 115VAC operation the blue jumper provided(taped to wire harness) must be inserted into motor power connector. See diagram.
AC Supply - 120/208-230VAC
EC motors are equipped with a control module that allows for accurate manual
adjustment of motor speed. Motor speed range is from 300 to 1800 rpm or maximum
rpm for that model.
The control module features a 4 digit LED display that indicates % demand of full
speed and motor speed in rpm. The display also indicates an error code message
for minor diagnostics if required.
Motor speed can be changed by adjusting the speed control pot located on the
contr
ol module. A small screwdriver can be used to make the speed adjustment.
MESSAGE DISPLAYED
Spd- followed by the instantaneous speed in rpm
dE- followed by S + demand in %
E1- No communications
E2- Under Voltage
EC (ELECTRONICALLY CONTROLLED) MOTOR SPEED CONTROL
Note: EC motors have a soft start feature. When the power is turned on the control module gathers information from the motor then begins the start up
process. After a few seconds the motor will start to turn and reach full set speed in 10-30 seconds.
Remote Speed Control Option (please contact factory for further information)
120 VAC System 208-230 VAC System   
120/208-230 VAC
EC Motor wiring diagram
Control
Module
EC Motor
Blue jumper -
for 120 VAC only
Caution: Operating the motor at 208-230VAC with the jumper will cause significant damage to the motor.
Product specificaties
| Merk: | Canarm |
| Categorie: | Ventilator |
| Model: | GSQ135-D |
Heb je hulp nodig?
Als je hulp nodig hebt met Canarm GSQ135-D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Ventilator Canarm
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
Handleiding Ventilator
- Ventilator Royal Sovereign
- Ventilator Mistral
- Ventilator Schweigen
- Ventilator Panasonic
- Ventilator Ozito
- Ventilator Lian Li
- Ventilator VisionAir
- Ventilator Korona
- Ventilator Dyson
- Ventilator Neo
- Ventilator Izzy
- Ventilator Windmill
- Ventilator Keystone
- Ventilator Crivit
- Ventilator Midea
Nieuwste handleidingen voor Ventilator
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025