Blaupunkt BC OE2 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Blaupunkt BC OE2 (4 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Operating and Installation Instructions
REVERSE CAMERA
BC OE2
Ground the wire through the exterior body of the vehicle and keep connection intact.
Attention
Remove protective
lm from camera
lens before use.
Take extra
precautions when
setting up the
connection near
petrol tank and wires.
Please connect
Red Wire with
reverse light.
Display Monitor/
Car Radio
P
R
N
D
L
2
BC OE2
Red Wire
Black Wire (Ground)
Reverse Light
Display Monitor/Car Radio
BC OE2
Disclaimer
In no event shall Blaupunkt be liable f or any direct, indirect, punitive, incidental, special consequential damages, to property or lif e, improper storage,
whatsoever arising out of or connected with the use or misuse of our products.
USA & CANADA : Product no intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased as-is.
No warranty, express or implied is provided in the U.S. and Canada.
Installation Diagram
Power Supply : DC12V±3V
Current Consumption : 50mA
Resolution : 750 TVL
Optical Format : 1/3”
Image Sensor : CMOS
Eective Pixels : 960 x 576
Lens Angle : 170° (D), 120° (H) , 100° (V)
Electronic Shutter : 1/60
SPECIFICATION
~ 1/100000 sec
White Balance : Auto
Humidity : up to 95%
Water Proof : Yes
Illumination Min. : 0.1 Lux
TV System : PAL/NTSC
Operation Temperature : -20°C ~ +70°C
Storage Temperature : -20°C ~ +70°C
TROUBLESHOOTING
Problem
Display monitor / car radio does not show
reverse view when reversing
Display monitor / car radio does not show
reverse view even after correcting the view
setting
Reverse view does not show even after
restarting the display monitor/ car radio
Reverse view does not show even though
power supplies of the reverse light or the
rear car plate light is properly connected
Solution
Examine if the viewing mode is set to correct
reverse view
Restart the display monitor / car radio
Examine if the power supplies of the reverse
light or the rear car plate light is properly
connected
Examine if the power supply cables of the
reverse light or the rear car plate light is
damaged. Repair/replace if the cables are
damaged
1.1 At tail light
1.2 At hatch handle
1.3 Above car plate
Pictures are for illustration purpose only, see act ual vehicle for accurate installation location.
2.0 After installation
Adjust viewing angle
Loosen the screws on the rotating mount &
rotate the camera to the desired angle
i.
Remove one side
of the reverse light
socket from its
housing then
remove the bulb
from its socket
ii.Connect the reverse
light power cable to
the camera, screwn
the housing & camera
back into position
with a screwdriver
i.
Use a screwdriver
to remove the
original hatch
handle
ii.Mount the camera
where the original
hatch handle used
to be
i.
Remove the
rotating mount
before installation.
Drill an access
hole for the
camera cables
ii.Mount the camera
onto the acces hole
& secure it in
position with 3M
tape/ screws
1. Installation Locations 2. Adjust Angle


Product specificaties

Merk: Blaupunkt
Categorie: Fotocamera
Model: BC OE2

Heb je hulp nodig?

Als je hulp nodig hebt met Blaupunkt BC OE2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Fotocamera Blaupunkt

Handleiding Fotocamera

Nieuwste handleidingen voor Fotocamera