Black And Decker 3304-220 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Black And Decker 3304-220 (10 pagina's) in de categorie Router. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
Instruction Manual
3304-220 Plunge Cut Routers
154707/3304-220 5/17/02 2:34 PM Page 3
Getting the most out of your tool.
Please take time to read this manual and pay particular attention to the safety
rules we’ve provided for your protection. If you have any questions about your
tool please call:
1-800-9-BD TOOL
(1-800-923-8665)
WARNING: When using electric tools, basic safety precautions should
always be followed to reduce risk of fire, electric shock, and personal injury,
including the following:
READ ALL INSTRUCTIONS
Double Insulation
Double insulated tools are constructed throughout with two separate layers
of electrical insulation or one double thickness of insulation between you and
the tool’s electrical system. Tools built with this insulation system are not
intended to be grounded. As a result, your tool is equipped with a two prong
plug which permits you to use extension cords without concern for main-
taining a ground connection.
NOTE: Double insulation does not take the place of normal safety precau-
tions when operating this tool. The insulation system is for added protection
against injury resulting from a possible electrical insulation failure within the
tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT
PARTS. Repair or replace damaged cords.
IMPORTANT SAFETY INSTRUCTIONS
0
1
220 VOLT PLUG
154707/3304-220 5/17/02 2:34 PM Page 4
1
Safety Instructions For All Tools
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain.
Don’t use power tools in damp or wet locations. Keep work area well lit. Do
not use tool in presence of flammable liquids or gases.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, and refrigerator enclosures.
•KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place — out of reach of children.
• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it
was intended.
•USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a
heavy-duty tool. Don’t use tool for purpose not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
• DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your
hand and it frees both hands to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing acces-
sories. Inspect tool cords periodically and if damaged, have repaired by autho-
rized service facility. Inspect extension cords periodically and replace if dam-
aged. Keep handles dry, clean, and free from oil and grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and
when changing accessories, such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch.
Be sure switch is off when plugging in.
• EXTENSION CORDS. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. The following table shows
the correct size to use depending on cord length and nameplate ampere rat-
ing. If in doubt, use the next heavier gage. The smaller the gage number, the
heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more AWG
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate
tool when you are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction manual. Have defective
switches replaced by authorized service center. Do not use tool if switch does
not turn it on and off.
SAVE THESE INSTRUCTIONS
154707/3304-220 5/17/02 2:34 PM Page 1


Product specificaties

Merk: Black And Decker
Categorie: Router
Model: 3304-220

Heb je hulp nodig?

Als je hulp nodig hebt met Black And Decker 3304-220 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Router Black And Decker

Handleiding Router

Nieuwste handleidingen voor Router