Binatone Action 950 Handleiding

Binatone Radio Action 950

Lees hieronder de 📖 handleiding in het Nederlandse voor Binatone Action 950 (10 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10

USER GUIDE

Private mobile radio with twin charger

1. LCD Screen

Antenna

LCD Screen

- Displays the

current channel

selection and other

radio s ymbols.

PTT (PUSH to

TALK) button

–Press and hold to

transmit. CALL button

-Press to send

Ringing tone to

other PMR units.

MENU Button

-Press to switch

between Modes.

Sp reake

Ear/Mic/Charge

jack

PWR/VOL Switch

– Rotate clockwise/

counter clockwise

to turn

ON or OFF, and

adjust the volume.

MIC (Microp )hone

UP/DOWN

Buttons –

Press to change

channels, volume,

and to select

settings during

p g gro rammin .

the unit

Channel Number. Changes from 1 to

8 as selected by the user.

Digital Code. Changes from 1 to 83

as selected by the user.

Displays the Battery charge level.

When the bars are reduced, the

battery needs recharging.

TX Displayed when transmitting a signal.

RX Displayed when receiving a signal.

DCS Displayed when the Digital Code System is turned On.

VOX Displayed when the VOX feature is enabled.

SCAN Displays when the PMR is scanning all channels.

Displayed when the Key Lock feature is activated.

Displayed when a CTCSS sub-channel is turned on.

Displays when the call signal is ON.

Displays when the vibrator function is activated.

Action 950

CTCSS Code. Changes from 1 to 38

as selected by the user.

Displayed when the Dual Watch function is turned ON.

DCM

CTCSS

Receiver (LED)

Lights up when you

are receiving signals

Transmit (LED)

2. Installation

2.1 Removing the Belt Clip

2.2 Installing the Belt Clip

2.4 Charging the Batteries

a. Pull the Belt Clip latch up

(away from the ) Action 950

b. While pulling the Belt Clip

latch,slide the Belt Clip up as

shown in Figure1.

Belt Clip latch

Fig gure 1 Fi ure 2

a. Slide the Belt Clip into the

slot as shown in Figure2.

A “click” indicates the Belt

Clip is locked into position.

Fig gure 3 Fi ure 4

a. Unclip the battery cover latch at the bottom of the cover, and lift

the battery cover off.

Important

Read these Safety Warnings before you charge the batteries.

When placing the Action 950 in the charger, use only the power

supplies listed in the user instructions supplied with the Action 950.

Don’t try to recharge non-rechargeable batteries.

Make sure the battery compartment cover is securely locked in

place when you are charging the batteries.

Dispose of used batteries safely and in a way that will not harm

the environment- never try to burn them or put them anywhere they

could get burnt or punctured.

Don’t leave dead batteries in your units. Action 950

They might leak if you do.

a. Insert the small plug on the end of the mains adaptor into the

Power-in Connection Jack at the back of the desktop charger.

b. Plug the mains adaptor into a 240V AC, 50Hz main socket with

the switch on the socket set to OFF.

c. Switch ON the mains socket.

Using any other adaptor will result in non-compliance with

EN60950-1 and will invalidate any approvals & warranty.

2.3 Installing the Batteries

Caution: Observe the proper battery polarity orientation when

installing batteries. Incorrect positioning can damage both the

batteries and the unit.

b. Insert the 4 “AAA” size rechargeable batteries by following the

c. Replace the Battery Compartment Cover. See Figure 4.

+ polarity marking inside the Battery Compartment as shown in /-

Figure 3.

Use only the mains adaptor provided.

%DWWHU\ PHWHU

%DWWHU\ OLIH

d. P g a p g p i nlace the uni s the char Action 950 t in e cradle in n u ri ht os tio .

The Charge LED indicators will light up.

completely run down. New batteries take up to 14 hours to fully

charge.

e. It takes about 10 hours to fully recharge the batteries if they are

Important:

Always turn off the PMR units

when charging. This will

shorten the charging time.

Mains socket

OR: Charging the batteri s ( sing ada tor) e u p

Lift the charge socket cover located on

the right side of the handset.

Insert the round connector of

the 9.0V DC/200mA adaptor

into the charge jack.

Plug the mains adaptor into a

240V AC, 50Hz main socket

with the switch on the socket

set to OF . e onlyF Us the mains

adaptor provided.

Then switch ON the mains socket.

Mic/Earpiece jack

Charge jack

The battery meter is located in the left corner of the LCD Screen. It

appears like a battery with three bars inside. These indicate the

amount of power available. When the battery level reaches its

minimum level in PMR on mode, the unit will emit two beep tones

and automatically power off.

The can detect the battery charge in 4 levels; Action 950

Battery charge at high level.

Battery charge at medium level.

Battery charge at low level. At this level, the Action 950 will

Important: Charge the unit for 10-14 hours.

Battery charge at very low level. When the battery level

reachs its minimum level in Action 950 on mode, the unit will

Important: Charge the unit for 10-14 hours.

CAUTION : Risk of explosion if battery is replaced by an

inco rect pe. D spos of used batter es ac o d ng to ther ty i e i c r i

instructions.

The Action 950 h as a built in power saver to make the batteries

emit a “beep” sound for every 10 seconds in normal mode.

emit two beep tones and automatically turn off the

power .

last longer. But when you are not using the units, turn them

OFF to conserve battery power.

Product specificaties

Merk:	Binatone
Categorie:	Radio
Model:	Action 950
Ondersteund aantal accu's/batterijen:	4
Maximumbereik:	10000 m
Frequentie:	446.00625 - 446.09375 MHz
Oplaadbaar:	Ja
Riemclip:	Ja
Batterijen inbegrepen:	Ja
Type batterij:	AAA
Aantal kanalen (totaal):	968 kanalen