Behringer System 100 172 Phase Shifter/Delay/LFO Handleiding
Pagina's 2 Engels Synthesizer
Bekijk de handleiding van Behringer System 100 172 Phase Shifter/Delay/LFO gratis online of download de PDF. 112 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
Quick Start Guide
SYSTEM 100
172 PHASE SHIFTER/
DELAY/LFO
Legendary Analog Phase Shifter/
Delay/LFO Module for Eurorack
Controls
(1) CV IN – Accepts voltage from an external source to
control or modulate the phase shifter frequency or audio
delay time. If no jack is inserted the LFO can be used to
modulate the eect.
(2) MOD INTENSITY – Controls how much the eect is
modulated by the LFO or external CV input.
(3) EFFECT ON/OFF – Engages or disengages the
eect section.
(4) SHIFT FREQ – Adjusts the frequency of the phase shifter.
(5) SIG IN – Accepts an incoming signal via 3.5 mm TS cable.
(6) SIG OUT – Sends the signal from the eect section.
(7) RESONANCE – Adjusts the amount of signal that is fed
back through the eect.
(8) DELAY TIME – Adjusts the time of the delay eect.
(9) FREQUENCY – Controls the LFO output frequency.
(10) LFO OUT – Sends the LFO signal as a triangle and inverted
triangle wave.
(11) THRESHOLD – Controls the input voltage level required to
trigger the gate.
(12) GATE IN – Accepts an incoming gate signal via 3.5 mm
TS cable.
(13) GATE OUT – Send the gate delay signal via 3.5 mm
TS cable.
(14) GATE TIME – Controls the gate length.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
(1)
(2)
(8)
(6)(5)(4)
(11) (14)
(7)
(13)
(9)
(10)
(3)
(12)
Product specificaties
| Merk: | Behringer |
| Categorie: | Synthesizer |
| Model: | System 100 172 Phase Shifter/Delay/LFO |
Heb je hulp nodig?
Als je hulp nodig hebt met Behringer System 100 172 Phase Shifter/Delay/LFO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Synthesizer Behringer
Behringer Model D Handleiding Behringer Eurorack Stand (3-Tier) Handleiding Behringer System 55 994 Multiples Handleiding Behringer Eurogrand EG8180-BK Handleiding Behringer 992 Control Voltages Handleiding Behringer System 35 Handleiding Behringer Oscillator Module 1004 Handleiding Behringer System 15 Handleiding
Alle Behringer Synthesizer handleidingen
Populair in Synthesizer
Handleiding Synthesizer
Nieuwste handleidingen voor Synthesizer
Erica Synths Black Dual EG / LFO Handleiding Benidub DS71 Dub Siren Handleiding Modal Electronics CARBON8X Handleiding DTronics DT-DX Handleiding Erica Synths Snare Handleiding Korg 01/W ProX Handleiding Roland XPS-10X Handleiding Moog Messenger Handleiding Motas Electronics Motas-6 Handleiding Roland JUNO-D8 Handleiding