Baumatic BWL5 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Baumatic BWL5 (16 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
Washing Machine
BWL5
2EN
1 Important safety instructions
This section contains safety instructions that will
help protect from risk of personal injury or property
damage. Failure to follow these instructions shall void
any warranty.
General safety
8 years and older children and people with
reduced physical, sensory, and mental abilities
as well as unskilled or inexperienced persons
can use this appliance provided that they are
supervised and instructed on safe use of the
appliance as well as to the related dangers.
Children should not play or tamper with the
appliance. Cleaning and user maintenance
should never be performed by children unless
supervised by a responsible adult.
Never place the product on a carpet-covered
floor; otherwise, lack of airow beneath the
machine will cause electrical parts to overheat.
This will cause problems with your product.
Do not operate the product if the power cable
/ plug is damaged. Call the Authorized Service
Agent.
Have a qualified electrician connect a
10-Ampere fuse to the installation location of the
product.
If the product has a failure, it should not be
operated unless it is repaired by the Authorized
Service Agent. There is the risk of electric shock!
This product is designed to resume operating
in the event of powering on after a power
interruption. If you wish to cancel the
programme, see "Cancelling the programme"
section.
Connect the product to a grounded outlet
protected by a fuse complying with the values
in the "Technical specifications" table. Do not
neglect to have the grounding installation made
by a qualified electrician. Our company shall
not be liable for any damages that will arise
when the product is used without grounding in
accordance with the local regulations.
The water supply and draining hoses must be
securely fastened and remain undamaged.
Otherwise, there is the risk of water leakage.
Never open the loading door or remove thelter
while there is still water in the drum. Otherwise,
risk of ooding and injury from hot water will
occur.
Do not force open the locked loading door. The
loading door will be ready to open just a few
minutes after the washing cycle comes to an
end. In case of forcing the loading door to open,
the door and the lock mechanism may get
damaged.
Unplug the product when not in use.
Never wash the product by spreading or pouring
water onto it! There is the risk of electric shock!
Never touch the plug with wet hands! Never
unplug by pulling on the cable, always pull out
by grabbing the plug.
Use detergents, softeners and supplements
suitable for automatic front Load washing
machines only.
Follow the instructions on the textile tags and on
the detergent package.
The product must be unplugged during
installation, maintenance, cleaning and repairing
procedures.
Always have the installation and repairing
procedures carried out by the Authorized
Service Agent. Manufacturer shall not be
held liable for damages that may arise from
procedures carried out by unauthorized
persons.
Intended use
This product has been designed for domestic
use. It is not suitable for commercial use and it
must not be used out of its intended use.
The product must only be used for washing and
rinsing of laundry that are marked accordingly.
The manufacturer waives any responsibility
arisen from incorrect usage or transportation.
Children's safety
Electrical products are dangerous for the
children. Keep children away from the product
when it is in use. Do not let them to tamper with
the product. Use child lock to prevent children
from intervening with the product.
Do not forget to close the loading door when
leaving the room where the product is located.
Store all detergents and additives in a safe place
away from the reach of the children.
2 Installation
Refer to the nearest Authorised Service Agent for
installation of the product. To make the product ready
for use, review the information in the user manual
and make sure that the electricity, tap water supply
and water drainage systems are appropriate before
calling the Authorized Service Agent. If they are not,
call a qualified technician and plumber to have any
necessary arrangements carried out.
Preparation of the location and electrical, tap
water and waste water installations at the place
of installation is under customer's responsibility.
Installation and electrical connections of the
product must be carried out by the Authorized
Service Agent. Manufacturer shall not be
held liable for damages that may arise from
procedures carried out by unauthorized
persons.
Prior to installation, visually check if the product
has any defects on it. If so, do not have it
installed. Damaged products cause risks for
your safety.
Make sure that the water inlet and discharge
hoses as well as the power cable are not
folded, pinched or crushed while pushing the
product into its place after installation or cleaning
procedures.
Appropriate installation location
Place the machine on a rigidoor. Do not place
it on a long pile rug or similar surfaces.
Total weight of the washing machine and the
dryer -with full load- when they are placed
3EN
ontopofeachotherreachestoapprox.180
kilograms. Place the product on a solid and flat
floor that has sufficient load carrying capacity!
 Donotplacetheproductonthepowercable.
 Donotinstalltheproductatplaceswhere
temperaturemayfallbelow0ºC.
 Placetheproductatleast1cmawayfromthe
edges of other furniture.
Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement
by pulling the ribbon.
Removing the transportation locks
A Donotremovethetransportationlocksbefore
taking out the packaging reinforcement.
A Remove the transportation safety bolts before
operating the washing machine, otherwise, the
product will be damaged.
1. Loosen all the bolts with a spanner until they
rotate freely (C).
2. Remove transportation safety bolts by turning
them gently.
3. AttachtheplasticcoverssuppliedintheUser
Manual bag into the holes on the rear panel. (P)
C Keep the transportation safety bolts in a safe
place to reuse when the washing machine
needs to be moved again in the future.
C Never move the product without the
transportation safety bolts properly fixed in
place!
Connecting water supply
C Thewatersupplypressurerequiredtorunthe
productisbetween1to10bars(0.1–1MPa).
Itisnecessarytohave10–80litersofwater
flowing from the fully open tap in one minute
to have your machine run smoothly. Attach a
pressure reducing valve if water pressure is
higher.
C Ifyouaregoingtousethedoublewater-inlet
productasasingle(cold)water-inletunit,you
must install the supplied stopper to the hot
water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
C Ifyouwanttousebothwaterinletsofthe
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
A Models with a single water inlet should not be
connectedtothehotwatertap.Insuchacase
the laundry will get damaged or the product will
switch to protection mode and will not operate.
A Donotuseoldorusedwaterinlethoseson
thenewproduct.Itmaycausestainsonyour
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose(left)(max.90ºC)isforhotwaterinlet,blue
hose(right)(max.25ºC)isforcoldwaterinlet.
A Ensure that the cold and hot water connections
are made correctly when installing the product.
Otherwise,yourlaundrywillcomeouthotatthe
end of the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a
wrench when tightening the nuts.
3. Openthetapscompletelyaftermakingthe
hose connection to check for water leaks at
theconnectionpoints.Ifanyleaksoccur,turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not in
use.
Connecting to the drain
 Theendofthedrainhosemustbedirectly
connected to the wastewater drain or to the
washbasin.
A Your house will be flooded if the hose comes out
of its housing during water discharge. Moreover,
there is risk of scalding due to high washing
temperatures! To prevent such situations and to
ensure smooth water intake and discharge of
the machine, fix the end of the discharge hose
tightly so that it cannot come out.
 Thehoseshouldbeattachedtoaheightofat
least 0cm,and 0cmatmost.6 9
 Incasethehoseiselevatedafterlayingiton
the floor level or close to the ground (less than
60cmabovetheground),waterdischarge
becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the
heights described in the figure.


Product specificaties

Merk: Baumatic
Categorie: Fornuis
Model: BWL5

Heb je hulp nodig?

Als je hulp nodig hebt met Baumatic BWL5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Fornuis Baumatic

Handleiding Fornuis

Nieuwste handleidingen voor Fornuis