Axxess AXLOC4M-150 Handleiding

Bekijk gratis de handleiding van Axxess AXLOC4M-150 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.3 sterren uit 8 reviews. Heb je een vraag over Axxess AXLOC4M-150 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

AXLOC4M-150AXLOC4M-150

INSTALLATION INSTRUCTIONSINSTALLATIONINSTRUCTIONS

AXLOC4M-150AXLOC4M-150

INSTALLATIONINSTRUCTIONSINSTALLATIONINSTRUCTIONS

REV. 12/13/19REV. 12/13/19© COPYRIGHT 2019 METRA ELECTRONICS CORPORATION © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION

Integrate • AxxessInterfaces.comIntegrate • AxxessInterfaces.com

REV. 12/13/19REV. 12/13/19© COPYRIGHT 2019 METRA ELECTRONICS CORPORATION © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION

Integrate • AxxessInterfaces.comIntegrate • AxxessInterfaces.com

A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.

The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line

level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add

aftermarket amplifiers. This device will also detect the presence of an audio signal and then

generate a +12V output that can be used to turn-on an aftermarket amplifier.

Features and specifications

The LOC is able to handle 150 watts per channel continuous input without over heating.

The input circuitry is designed to correct the crossover distortion commonly found on

standard LOCs while providing a high to low level step down of 6:1. Output audio level is

infinitely adjustable using the onboard, high quality potentiometers. The remote output

or amplifier trigger is rated at 500mA (+12V) and will easily handle an outboard relay if

additional current is needed. The remote output will trigger instantaneously when the LOC

detects a DC voltage on the white, left + audio input wire above 5V or a very low audio

signal. It will shut off 60 seconds after no signal is detected.

Installation

The LOC should be installed on a stereo’s speaker output wires or the output wires on an

OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo

in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM

speakers. Please refer to the wiring diagram for the input connection details.

Continued on next page

A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.

The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line

level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add

aftermarket amplifiers. This device will also detect the presence of an audio signal and then

generate a +12V output that can be used to turn-on an aftermarket amplifier.

Features and specifications

The LOC is able to handle 150 watts per channel continuous input without over heating.

The input circuitry is designed to correct the crossover distortion commonly found on

standard LOCs while providing a high to low level step down of 6:1. Output audio level is

infinitely adjustable using the onboard, high quality potentiometers. The remote output

or amplifier trigger is rated at 500mA (+12V) and will easily handle an outboard relay if

additional current is needed. The remote output will trigger instantaneously when the LOC

detects a DC voltage on the white, left + audio input wire above 5V or a very low audio

signal. It will shut off 60 seconds after no signal is detected.

Installation

The LOC should be installed on a stereo’s speaker output wires or the output wires on an

OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo

in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM

speakers. Please refer to the wiring diagram for the input connection details.

Continued on next page

A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.

The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line

level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add

aftermarket amplifiers. This device will also detect the presence of an audio signal and then

generate a +12V output that can be used to turn-on an aftermarket amplifier.

Features and specifications

The LOC is able to handle 150 watts per channel continuous input without over heating. The

input circuitry is designed to correct the crossover distortion commonly found on standard

LOCs while providing a high to low level step down of 6:1. Output audio level is infinitely

adjustable using the onboard, high quality potentiometers. The remote output or amplifier

trigger is rated at 500mA (+12V) and will easily handle an outboard relay if additional

current is needed. The remote output will trigger instantaneously when the LOC detects a

DC voltage on the white, left + audio input wire above 5V or a very low audio signal. It will

shut off 60 seconds after no signal is detected.

Installation

The LOC should be installed on a stereo’s speaker output wires or the output wires on an

OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo

in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM

speakers. Please refer to the wiring diagram for the input connection details.

Continued on next page

A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.

The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line

level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add

aftermarket amplifiers. This device will also detect the presence of an audio signal and then

generate a +12V output that can be used to turn-on an aftermarket amplifier.

Features and specifications

The LOC is able to handle 150 watts per channel continuous input without over heating.

The input circuitry is designed to correct the crossover distortion commonly found on

standard LOCs while providing a high to low level step down of 6:1. Output audio level is

infinitely adjustable using the onboard, high quality potentiometers. The remote output

or amplifier trigger is rated at 500mA (+12V) and will easily handle an outboard relay if

additional current is needed. The remote output will trigger instantaneously when the LOC

detects a DC voltage on the white, left + audio input wire above 5V or a very low audio

signal. It will shut off 60 seconds after no signal is detected.

Installation

The LOC should be installed on a stereo’s speaker output wires or the output wires on an

OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo

in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM

speakers. Please refer to the wiring diagram for the input connection details.

Continued on next page

Product specificaties