Audio-Technica ATM73a Handleiding

Bekijk gratis de handleiding van Audio-Technica ATM73a (2 pagina’s), behorend tot de categorie Hoofdtelefoon. Deze gids werd als nuttig beoordeeld door 8 mensen en kreeg gemiddeld 4.0 sterren uit 8 reviews. Heb je een vraag over Audio-Technica ATM73a of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CARDIOID CONDENSER HEADWORN MICROPHONE

- Ideal for drummers, keyboard players or anyone requiring hands-free

operation.

- Comfortable, unobtrusive headband design with side-of-mouth pickup.

- Belt-mounted power module operates on battery or phantom power.

- Cardioid polar pattern improving isolation of desired sound source.

- Also available as: ATM73cW - less power module; 1.4m cable terminated

with locking 4-pin connector for A-T UniPak

™ wireless systems.

The ATM73a required 11V to 52V DC phantom power or a 1.5V AA

battery for operation. A battery need not be in place for phantom power

operation.

Battery installation: Remove the cap from the top of the power module.

Insert a fresh 1.5V AA battery (“+” end toward the cap release button),

then reassemble the power module. Alkaline batteries are recommended

for longest lift. Remove the battery during long-term storage.

Output from the power module’s XLRM-type connector is low impedance

(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground

(shield). Output phase is “Pin 2 hot” - positive acoustic pressure produces

positive voltage at Pin 2.

An integral 80Hz high-pass UniSteep®filter provides easy switching

from a at frequency response to a low-end roll-off. The roll-off position

reduces the microphone’s sensitivity to popping in close vocal use. It also

reduces the pickup of low-frequency ambient noise (such as trafc, air-

handling systems, etc.), room reverberation and mechanically coupled

vibrations.

For maximum stability and minimum visibility, the headband should be

worn around the back of the head, with each cushioned support pad

resting on the temple in front of the ear. The cable should remain clipped

to the headband, with slack at the boom connection. The headset is

designed so the microphone descends from the left support pad.

Avoid leaving the microphone in the open sun or in areas where

temperatures exceed 40°C for extended periods. Extremely high humidity

should also be avoided.

FORM No. ATGC-L0035-06-E

Machida • Tokyo • Japan

SPECIFICATIONS

ELEMENTFixed-change back plate permanently

polarized condenser

POLAR PATTERNCardioid

FREQUENCY RESPONSE40-15,000 Hz

LOW FREQUENCY ROLL-OFF80 Hz, 18 dB/octave

OPEN CIRCUIT SENSITIVITY

(Phantom / Battery)

-55 dB (1.7 mV) /

-56 dB (1.5 mV) re 1V at 1 Pa

IMPEDANCE (Phantom / Battery)200 ohms / 270 ohms

MAXIMUM INPUT SOUND LEVEL

(Phantom / Battery)

146 dB / 132 dB SPL,

1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical)

(Phantom / Battery)

111 dB / 97 dB,

1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO59 dB, 1 kHz at 1 Pa

PHANTOM POWER REQUIREMENTS11-52V DC, 2 mA typical

BATTERY TYPE1.5V AA/UM3

BATTERY CURRENT/LIFE0.4 mA / 1200 hours typical (alkaline)

SWITCHES Off, on-at, on-roll-off

WEIGHT MICROPHONE

POWER MODULE

31 g

139 g

DIMENSIONS HEADSET

MICROPHONE

POWER MODULE

165.0 mm - nominal at widest point,

67.0 mm - exible boom,

10.0 mm - diameter,

84.0(H) x 63.0(W) x 22.9(D) mm

OUTPUT CONNECTORIntegral 3-pin XLRM-type

CABLE 1.4 m long (permanently attached to

microphone), 2.6 mm diameter,

2-conductor shielded cable with TA3F-

type connector

ACCESSORIES FURNISHEDAT8531 power module;

AT8128 windscreen;

AT8125l windscreen; battery

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Response in dB

Roll-off

Product specificaties