Audio-Technica AT8688S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica AT8688S (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
ANTI-SHOCK MICROPHONE STAND
- Heavy die-cast construction and non-slip bottom pads minimize
coupling of surface vibration to the unit.
-Low-proledesignwithlow-reectanceblacknishforminimum
visibility.
-Theimprovedtightermicrophonesocketforreducetheswingof
the microphone.
There are two models for application - AT8688 / AT8688S. Combin-
ing technical and artistic features in the design, the microphone
standsnd theirvariousapplicationsinthe eld ofbroadcast and
communications.
Thetwomodels come with a low reflectance, matte-black finish.
The AT8688 features a 3-pin XLRF type receptacle on the input port
and 3-pin XLRM type receptacle on the output port. Both recepta-
clesaregold-platednish.TheAT8688Salsofeaturesaphantom-
powered mute switch with a LED indicator that meets stringent
audio transmission requirements and adapts to various types of
microphone.
MOUNTING / CONNECTIONS:
1. Insert a microphone into microphone stand while pressing the top
connector.
2. Connect XLRF-3 side of the cable to the stand and the other side
to your equipment.
3. To remove the microphone, pull out the microphone while
pressing the release tab of the XLRF circular connector of the
microphone stand.
Note thatthemicrophonestandcouldbreakandcauseaninjuryif
it is dropped.
FORM No. ATGC-L0181-11-E
MachidaTokyoJapan
MECHANICAL SPECIFICATIONS
MIC ATTACHMENT XLRF-type,
XLRM-type
XLRF-type,
XLRM-type,
Switch with LED
DIMENSIONS
WIDTH
DEPTH
HEIGHT
91 mm
132 mm
38 mm
91 mm
132 mm
38 mm
WEIGHT 800 g 840 g
DESCRIPTION
TheseAudio-Technicaanti-shockmicrophonestandseffectively
isolate mounted microphones from impact vibration and
mechanical noise normally transmitted from the surface.
They are intended for use with microphones stood on lecterns,
pulpits, conference tables and similar surfaces. Ideal for use
withgooseneckmicrophonesandotherquick-mounttype
microphones using industrial standard XLRM 3-pin type
connectors.
AT8688S OFF SWITCH
The AT8688S features a newly design press-on/press-off switch
circuit that controls the microphone, the mute attenuation level up to
64dB. The circuitry also operates a light in the switch, powered by
the 24-52V phantom source, to indicate when the mic is “on”.
AT8688S ELECTRICAL SPECIFICATIONS
PHANTOM POWER REQUIREMENTS 24~52V DC, 2 mA typical
INSERTION LOSS* 1.2 dB
OFF ATTENUATION* 64 dB minimum
*150ohmsource,100kohmload
- 以重型压铸技术制造,底部装有防震胶垫,可减低由
- 不显眼设计及磨砂黑色涂层,可增强在严肃场合使用
- 改良的紧贴话筒插座,能减低话筒的摆动情况。
置有两个可供选择的型号 - AT8688 AT8688S,均结合
了技术和艺术性的设计意念和特点,使该话筒更适合在
广 使
这两个型号均涂上低反光及磨砂黑色涂层,并配以3
卡农母头插座,作为话筒插入端;另背面为 3针卡农公头插
座,作为话筒信号输出端,两端插座均为电镀金接点。另
AT8688S设有静音开关及开通指示灯,讲话者可自由控
制话筒收音工作,而该静音控制和指示灯需使用幻象供电
工作。
配置和连接
1 . 连 接 话 筒 : 把 话 筒 的 底 部 卡 农 插 头 , 调 节 至 话 筒 座 顶
2 . 连接放大器:把话筒座卡农输出插座,以标准3针 卡
农连线连接到其他器材,如话筒放大器、调音台等。
3 . 除 下 话 筒 : 按 下 话 筒 座 顶 部 圆 形 卡 农 插 座 的 释 放 片 ,
:如不小心把话筒座从高处掉下,可能会引起碰撞
损坏。
FORM No. ATGC-L0181-11-C
MachidaTokyoJapan
机械指标
话筒座配置 XLRF 卡农母座,
XLRM 卡农公座
XLRF 卡农母座,
XLRM 卡农公座,
开关带LED指示灯
外形尺寸
宽 -
深 -
高 -
91 mm
132 mm
38 mm
91 mm
132 mm
38 mm
重量 800 g 840 g
AT8688S 电气指标
幻象供电 直流 24~52V耗电 2 mA 典型
插入损耗* 1.2 dB
静音衰减* 64 dB (最小)
*150 欧姆输入阻抗,100,000 欧姆负载
三角桌面防震话筒座,设有防震绝缘胶,能有效减低安装
此话筒座配合鹅颈式的会议话筒后,非常适合使用在演讲、教
学 、 会 议 报 导 的 场 合 使 用 。 另 外 , 亦 可 配 套于 其 他 3针卡农
使
AT8688S 静音开关
AT8688S
64dB衰减。并设有24-52V
LED
后方输出端子


Product specificaties

Merk: Audio-Technica
Categorie: Niet gecategoriseerd
Model: AT8688S

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica AT8688S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Audio-Technica

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd