Atdec VFS-DV Handleiding

Atdec Niet gecategoriseerd VFS-DV

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec VFS-DV (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 109 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

TTop of

op of

Display

There are two mounting hole configurations:

• 75 x 75mm

• 100 x 100mm

from the Hardware supplied to suit

your Displa

your Display

yy.

Mounting Screws (x4)

VESA Plate

Component Checklist

VFS-DV

IMPORTANT INFORMATION:

Step 1. Check Components

Step 2. Attach Upright Pole to Base

! IMPORTANT - Install Visidec Freestanding/Double Vertical as per Installation Instructions.

Each Quickshift Donut supports a maximum weight of 12kg (26.5lbs)

! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.

! The manufacturer accepts no responsibility for incorrect installation.

Display Mounting

Screws

Hardware

Check you have received all parts against the component checklist and Hardware above.

M4x12mm (x8)

VESA Plate (x2)

M4x10mm (x8)

M4x16mm (x8)

Security Screw (x2)

Cable Ball (x4) Cable Clip (x3)

5/3mm Allen Key

(x1 each)

Installation Instructions

Freestanding Double Vertical l

Base

Upright Pole

TOOLS REQUIRED:

Phillips Head Screw Driver

M8x50mm

Screw (x1)

Step 3. Attach Quickshift Donuts to the Visidec Pole

(Ensure the cable slot faces towards the rear)

TIGHTEN

If the Quickshift Donut requires further

tightening use the supplied 5mm Allen key.

(Visidec 42mm pole shown)

Slot

Groove

Insert

Close the lever to lock the Quickshift

Donut in place.

Slide the Quickshift Donut onto the Pole.

Cable Slot

USER

BACK

TIGHTEN

FIRMLY

Upright Pole

M8x50mm Screw

5mm Allen Key

Attach the Upright Pole to the Base as shown

below. Ensure the Cable Slot faces towards the rear.

Quickshift

Donuts (x2)

Step 4. Attach the VESA Plate to your Display

100mm

75mm

100mm

Back of Display

LOOSEN

(Repeat steps 4 to 7 for each Display)

(Optional)

TIGHTEN (+kg)

Cable

Balls (x2)

Cable

Clips (x2)

LOOSEN (-kg)

Installation Complete

No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 12.10.11

Step 5. Attach your Display to the Quickshift Donut

HOOK

Back of Display

Quickshift Mount.

Hook the top of the VESA plate onto the

Press and hold the Release Buttons. Gently

push bottom of VESA Plate into Quickshift

Mount. Release Buttons to lock in place.

Release Button Phillips-head

Screwdriver

Security Screw

OPEN

Slide the Quickshift Donut to

desired position.

Connect cables to your Displays, routing

them down to the rear of the poles.

Push the cables into the slots, using either

the Cable Balls or Cable Clips to secure

them to the pole as shown.

Note: Ensure enough slack is left in cables

to allow for movement. When the slot in

each pole cannot be used, use the supplied

Cable Clips to secure the cables.

LOOSEN

Close the lever to lock the

Quickshift Donut in place.

Step 6. Adjust the Height of the Quickshift Donut

Step 7. Adjust the VESA Ball Mount

(Optional) Insert the Security Screw,

and tighten using a Phillips-head Screwdriver.

If necessary, adjust the tension

between the Donut and the Pole

using the 5mm Allen Key supplied.

Open the lever to loosen the

Quickshift Donut.

TIGHTEN

PUSH

Step 8. Cable Management

3mm Allen Key

Tension Plate

Position your Display to the desired viewing angle using

the ±20° tilt allowed by the VESA Ball Mount.

To make any adjustments, use the 3mm Allen Key

supplied. Apply half a turn at a time to each screw on the

Tension Plate to adjust evenly.

If the display does not hold its position, or is too resistant,

adjust the Tension Plate located at the rear of the VESA

Ball Mount.

Check the display, and the adjust again if necessary.

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	VFS-DV
Montagewijze:	Bureau
Geschikt voor schermmaten:	24 "
Maximale gewichtscapaciteit:	12 kg
Gewicht (imperiaal):	26.5 lbs
Draaihoek:	360 °
Pan bereik:	-40 - 40 °
Bereik kantelhoek:	-40 - 40 °
Bevestigingsstandaard:	VESA 75mm x 75mm / 100mm x 100mm / 200mm x 100mm