Atdec SD-POS-VBM-B2B Handleiding

Atdec Niet gecategoriseerd SD-POS-VBM-B2B

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec SD-POS-VBM-B2B (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Component Checklist

3mm Allen Key

M4x12mm (x4)

M4x16mm (x4)

VESA Plate (x1)

M4x10mm (x4)

Security Screw (x1)

Installation Instructions

SD-POS-VBM-B2B

IMPORTANT INFORMATION:

Step 1. Check Components

Step 3. Undo and Remove Back Pin

Step 4. Install Back to Back VESA Ball Mount

! IMPORTANT - Install Spacedec POS Multi Back to Back as per Installation Instructions.

! This product supports a maximum load of 20kg (44lbs).

! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.

! The manufacturer accepts no responsibility for incorrect installation.

Display Mounting

Screws

Hardware

Check you have received all parts against the component checklist and Hardware above.

Back to Back

VESA Ball Mount

Step 2. Preparation

Choose from one of the following options:

A. New POS Height Adjustable Back to Back Installation

Prior to installing a new POS Multi Back to Back Assembly,

you will need to:

Install a POS Height Adjustable product to the work surface

(refer to the SD-POS-HA Installation Instructions).

Remove the Top Cap (use a small screw driver).

B. Back to Back Conversion

Prior to converting an POS Multi Assembly,existing

you will need to:

Remove the existing Display (TV/Monitor).

Remove the Top Cap (use a small flat screw driver).

Top Cap

Existing POS Height

Adjustable Assembly

TIP: Be careful not to

damage the Top Cap.

Display l POS Multi Back to Back

NOTE: Phillips-head

screwdriver and Flat

screwdriver not supplied

3mm Allen Key

Grub Screw

LOOSEN

Using the 3mm Allen Key, undo the Grub Screw.

NOTE: This will be very tight

3mm Allen Key

Grub Screw

Back Pin

Remove the Back Pin but keep the Grub Screw for use later on.

REMOVE

3mm Allen Key

Back to Back

VESA Ball Mount

Grub Screw

Recess

TIGHTEN

Use the Grub Screw to Install the Back to Back VESA Ball Mount.

Ensure the Recess (shown) lines up with the Grub Screw before

tightening.

Grub Screws (x2)

Ensure both Grub Screws are tightened as firmly as possible.

(optional)

Top Cap

PUSH

Installation Complete

Step 6. Install Top Cap

No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 03.07.13

Step 9. Attach your Display to the POS Assembly

Step 10. Adjust the VESA Ball Mount

Loop the Security Cable (Kensington or similar)

around the internal post of the POS Assembly.

Feed the other end of the cable through the POS

Assembly and out the Cable Management Hole.

After you have attached the monitor (As directed

in Step 8) install the lock to the monitor as per the

manufacturer guidelines.

Note: Security Cable Not Included

Step 5. (Optional) Install Monitor Security Cable

Push down firmly to attach the Top Cap.

These Installation Instructions secure

the POS Multi using the provided

fasteners from the above work surface.

For advanced Security Installation from

below the work surface. Please refer to

the

Advanced Security Installation

Addendum.

Advanced Security Installation

HOOK

Back of Display

Quickshift Mount.

Hook the top of the VESA plate onto the

Press and hold the Release Buttons. Gently

push bottom of VESA Plate into Quickshift

Mount. Release Buttons to lock in place.

PUSH

Release Button Back of Display

TIGHTEN

Phillips-head

Screwdriver

Security Screw

Back of Display

Position your Display to the desired viewing angle using the 40 °

angular movement allowed by the VESA Ball Mount.

If the display does not hold its position, or is too

resistant, adjust the Tension Plate located at the

rear of the VESA Ball Mount.

To make any adjustments, use the 3mm Allen Key

supplied. Apply half a turn at a time to each screw

on the Tension Plate to adjust evenly.

Check the display, and the adjust again if necessary.

Tension Plate

3mm Allen Key

TIGHTEN (+kg)

LOOSEN (-kg)

Push out to remove

Cable Access Cap

PUSH

Pull cables out through

Rear Cable Access Port.

Step 8. Attach the VESA Plate to your Display

Step 7. Install Monitor Cables

Option 2: When you do not want to route the

cables below the work surface.

OUT

Option 1:

There are two mounting

hole configurations:

• 75 x 75mm

• 100 x 100mm

Choose appropriate

Mounting Screws from

the Hardware supplied

to suit your Display.

Prior to attaching your monitor,

install the monitor cables.

Run them through the Front

Cable Access Port, down the

pole and out of the Cable

Access Hole in the work

surface.

VESA Plate

Mounting Screws (x4)

TOP OF

DISPLAY

Back of Display

75mm 75mm

100mm

ACCESS CAP

CABLE

100mm

Insert the Security Screw, and

tighten using a Phillips-head Screwdriver

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	SD-POS-VBM-B2B
Kleur van het product:	Zwart
Montagewijze:	Bureau
Maximale gewichtscapaciteit:	20 kg
Draaihoek:	360 °
Montage interface compatibiliteit (min):	75 x 75 mm
Montage interface compatibiliteit (max):	100 x 100 mm
Aantal displays ondersteund:	2
Maximale schermgrootte:	- "
Minimale schermgrootte:	- "