Atdec Ultra Slim TH-3060-LPT Handleiding

Atdec Niet gecategoriseerd Ultra Slim TH-3060-LPT

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec Ultra Slim TH-3060-LPT (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Wall Plate

Coach Screw

6mm (¼") hole

Timber Stud

Nylon Anchor (x4)

M5/6/8 Washer

(x4 each)

M5x30/16mm (x4 each)

M6x30/16mm (x4 each)

M8x30/16mm (x4 each)

Display Mounting

Screws

M4/5 Spacer (x4)

M6/8 Spacer (x4)

Note: Use a stud finder to accurately locate the center of

the stud. Ensure that all two screws fix securely into the stud.

Hardware

Coach Screw (x4)

Installation Instructions

TH-3060-LPT

Components Checklist

Flat Screen Wall Mount | Tilt

Wall Plate

Tilt Bracket (x2)

IMPORTANT INFORMATION

! IMPORTANT - Install Telehook 3060 Wall Mount as per Installation Instructions.

! This product supports a load from 8kg (17.6lbs) min. to 5

0kg (110lbs) max.

! This product only supports displays with mounting hole configurations from 200mm x 100mm min.

to 800mm x 500mm max.

! The manufacturer does not accept responsibility for incor

rect installation.

! Before installing this Telehook product, please check the

display ventilation requirements with your

LED/LCD manufacturer.

Step 1. Check Components

Step 2. Mounting the Wall Plate

Tools Required:



Power Drill



6mm (¼") drill bit





10mm (3/8") masonry drill bit





13mm (½") Socket Wrench or Shifter

Tip: Use a spirit level to ensure wall plate is horizontal.

Masonry Wall

Timber Stud

Check you have received all parts against the Component Checkli

Tension Tool

Wall Plate

Coach Screw

Nylon Anchor

10mm (

3/8

") hole



3/8

") drill bit



Spirit Level

Self-adhesive

Foam Pad

Push bottom of Display to lock the

Display to the Wall Plate. Listen

for a ‘CLICK’.

Step 3. Attaching Tilt Brackets to Display

Step 4. Attaching/Detaching Display to Wall Plate (2 people required)

Step 5. Cable Management Step 6. Set Display Tilt

Tension Tool

TIGHTEN

LOOSEN

NOTE: If necessary use the supplied

Tension Tool to adjust the tension in

the tilt mechanism.

TOP

With the Tilt Brackets attached to

the Display, lower the Hook Plates

onto the Wall Plate.

15° TILT

OPTIONAL: For larger screens, fix the

protective self-adhesive foam pad (supplied) to

the back of the panel. Position on the bottom

edge, where the Display touches the wall.

Once the Display is securely fastened to the

Wall Plate cut or fold the Release Ties so that

they cannot be seen from front of screen.

Spacer

(OPTIONAL, used only for

recessed mounting holes)

Mounting Screw

Tilt Bracket (right)

Washer

Tilt Bracket (left)

Tension

Nut

NOTE: The Tilt Brackets must be

mounted to the Display with the

Tension Nuts facing outwards, so it

is easily accessible from the side.

HOOK

PUSH

Detaching Display from the Wall Plate

To detach Display from wall plate, pull and

hold both Release Ties to disengage the

locking mechanism.

Whilst pulling the Release Ties, lift the Display

to unhook from the Wall Plate.

Self-adhesive

foam pad (OPTIONAL)

PULL

Hook Plate

PUSH

HOOK

WALL

PULL

No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent from Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 16.02.11©

Installation Complete

Pull Display out from the wall to allow access to the cable

ports on the back of the panel.

Connect cables, and push Display back against the wall.

TIP: To push Display back against the wall, pull

bottom edge outwards then push Display backwards.

1 Holding the Display by the top and bottom edges,

pull the Display straight out from the wall.

2 Tilt Display downward as desired.

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	Ultra Slim TH-3060-LPT
Kleur van het product:	Zwart
Materiaal behuizing:	Metaal
Kleur:	Nee
Montagewijze:	Muur
Geschikt voor schermmaten:	32 "
Maximale gewichtscapaciteit:	50 kg
Montage interface compatibiliteit (min):	200 x 100 mm
Montage interface compatibiliteit (max):	200 x 100 mm
Bereik kantelhoek:	-15 - 15 °
Afstand tot de muur (min):	25 mm