Atdec TH-UWM Handleiding

Atdec Niet gecategoriseerd TH-UWM

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec TH-UWM (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Installation Instructions

TH-UWM

Universal Wire Mount

Component Checklist

Hardware

IMPORTANT INFORMATION

! IMPORTANT - Install Telehook Universal Wire Mount as per Installation Instructions.

This product supports a maximum load of 50kg (110lbs).

This product supports VESA and Universal mounting hole configurations from 200mm up to 800mm wide (8”-31.5”).

! The manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Tools Required:

Phillips head screwdriver

Power drill

4.5mm (

”) drill bit

10mm (

”) masonry drill bit

10mm (

”) drill bit

10mm (

”) socket wrench

Spirit level

Step 2. Fix Universal Wire Mount to Display

Display Mounting Screws:

Wire Reel Assembly

Cable Access Support

M5 x 16mm / M5 x 25mm (x4 each)

M6 x 16mm / M6 x 25mm (x4 each)

M8 x 16mm / M8 x 25mm (x4 each)

Long

Spacer (x4)

Lower Support

M5 Bush (x2)

Hook Plates

(x2)

Flange

Screw (x2)

Short

Spacer (x4)

Dry Wall

Anchor (x2)

Concrete

Anchor (x2)

1 Grip the Wire Reel Assembly

as shown above. Pull firmly to

release wire to suit the Display

mounting hole pattern.

2 Select the appropriate hardware (supplied) to fasten the Wire Reels

LOOSELY to the back of the Display. Use top two mounting holes.

TIP: Only screw in half-way.

OPTIONAL: Use Short or Long Spacers

to pack recessed mounting holes. When

using M5 Mounting Screws use

the M5 Bushes supplied.

M5 Bush

Spacer

Mounting Screw

NOTE: All orange pads

should be facing outwards.

Cable

Access Support

Lower

Support

TOP

3 Fasten Cable Access Support and Lower Support FIRMLY to the

bottom two mounting holes.

PULL

FIRMLY

Wire Reel

Step 3. Tension Wire

Timber Stud Masonry Wall

Drill two holes 60mm deep using a

4.5mm

(

”)

drill bit.

Drill two holes 60mm (2.36”) deep using

a 10mm

(

”)

masonry drill bit.

Choose from one of the following mounting options (below): , Timber Stud Masonry Wall Dry Wall, or . Fasten the Hook Plates

to the wall, 150-500mm (6”-20”) apart (to suit wire length), using the appropriate mounting hardware supplied.

Step 4. Mount Hook Plates on Wall

CLICK

2 Fully tighten the Mounting Screws through both Wire Reels.

This will engage the internal reel lock mechanism.

TIP: FIRMLY Tighten as as possible.

3 For extra wire tension, twist the Wire Reels

in opposite directions (shown above).

TIP: Re-tighten Mounting Screws if necessary.

Mounting Screw

Hook Plate (x2)

Concrete Anchor

Dry Wall Anchor (x2)

Drill two holes using a 10mm

(

”)

drill bit.

Flange Screw

(x2)

Flange Screw

(x2)

Step 5. Hang Display on Wall Step 6. Cable Management

Installation Complete

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 16.05.11 ©

1 Gently lower the display until the wire is hanging over

the Hook Plates.

2 Use a spirit level to ensure the Display is hanging correctly.

1 Pull the bottom edge of the Display away from the wall

and fold out Cable Access Support.

2 Connect cables.

3 Fold in Cable Access Support to return the Display to flat

against the wall.

Cable Access

Support

WALL

Spirit level

Dry Wall 10-13mm thick. (0.4”-0.5”)

Ensure Dry Wall is in good condition,

with no sign of water damage or cracking.

1 Grip the lower half of the Wire Reel.

With your other hand twist the top,

taking in any slack in the wire

(repeat for opposite Wire Reel).

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	TH-UWM
Materiaal behuizing:	Metaal
Montagewijze:	Muur
Geschikt voor schermmaten:	26 "
Maximale gewichtscapaciteit:	50 kg
Montage interface compatibiliteit (min):	200 x 200 mm
Montage interface compatibiliteit (max):	200 x 200 mm
Afstand tot de muur (min):	15 mm