Atdec TH-3060-UFL Handleiding

Atdec Niet gecategoriseerd TH-3060-UFL

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec TH-3060-UFL (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

Component Checklist

Coach Screw (x4)

Nylon Anchor (x4)

Washer (x4)

5mm/4mm

Allen Key

M6x16mm

M6x25mm

M8x16mm

M8x25mm

TH-3060-UFL

Large-Medium TV Articulated Arm

IMPORTANT INFORMATION:

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

! IMPORTANT - Install 3060 Large-Medium TV Articulated Arm per Installation Instructions.

! This product supports a maximum load of 35kg (77lbs).

! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.

! The manufacturer accepts no responsibility for incorrect installation.

Display Mounting

Screws (x4 each)

Hardware

Tools Required:

Power drill

•

5mm (0.2”) drill bit

•

10mm (0.39”) masonry drill bit

•

Phillips head screw driver•

13mm (0.5”) socket wrench or shifter

•

Step 2. Changing position of Arm on Wall Mount

Step 3. Install Arm/Wall Mount to the Wall

Arm/Wall Mount

Mounting Bracket (x2)

Multiwasher (x4)

End Cap (x2)

Top Cap (x2)

Block (x2)

Locking

Screw (x4)

End Cap

Use Phillips head screw driver

to loosen and tighten.

Use 5mm Allen Key to

loosen and tighten.

Timber Stud Wall

Masonry Wall

- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.

- Secure the mounting plate to the wall using the Coach

Screws and Nylon Anchors supplied.

- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.

- Secure the mounting plate to the wall using the Coach

Screws supplied.

NOTE: Use a stud finder to accurately locate the centre

of the stud. Ensure that all screws fix securely into stud.

Four optional positions

Coach Screw

Washer

End Cap

Screw

Nylon Anchor

Drilled Hole

End Cap

Coach Screw

Washer

End Cap

Screw

Drilled Hole

End Cap

WALL WALL

Installation Instructions

Locking Blocks

Step 4. Attach Top Caps to the installed Arm/Wall Mount

Step 5. Attaching Mounting Brackets to Display

TOP

Back of Display

Display Mounting Screw

Multiwasher

Mounting Bracket

The mounting brackets support

hole configurations from

200x100mm to 700x500mm.

WALL

Pull down both Spring Lock

Ties to open catch.

Hook the Display

to the Arm/Wall

Mount.

1 HOOK

3 PUSH

DOWN

1 HOOK

2 LOCK 4

2 PULL

DOWN

3 PUSH

DOWN

Push down Display into catch. Release Spring Lock Ties

to secure Display.

NOTE: Ensure that Spring

Lock is fully engaged.

RELEASE 4

Step 6. Attaching/Detaching Display to the installed Arm (2 people required)

Top Cap

SLIDE

Step 7. Attach Locking Blocks to fully secure the Display

Back of Display

5mm Allen Key

4mm Allen Key

Installation Complete

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 05.06.13 ©

Step 7. Adjust Arm movement if necessary

Step 8. Adjust tilt and roll if necessary

Socket Wrench

LOOSEN

(-kg)

TIGHTEN

(+kg)

-5°

+15°

±5°

WALL

±180°

Position your display to the

desired viewing angle using the

angular movement allowed by

the double ball mount.

Depending on the weight of the

Display, it may be necessary to

make adjustments to the double

ball mount. If the display does

not hold its position, or is too

resistant, adjust the tension

plate located at the rear of the

double ball mount.

To adjust the tension plate, apply

half a turn at a time to each nut.

ENSURE NUTS ARE ADJUSTED

EVENLY.

CHECK THE DISPLAY, and then

adjust again if necessary.

±90°

Step 9. Cable Management

Back of Display

±90°

WALL

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	TH-3060-UFL
Kleur van het product:	Zwart
Materiaal behuizing:	Aluminium, Steel
Montagewijze:	Muur
Maximale gewichtscapaciteit:	35 kg
Paneelmontage-interface:	- mm
Bereik kantelhoek:	-5 - 15 °
Maximale schermgrootte:	- "
Minimale schermgrootte:	- "