Atdec SD-DO Handleiding

Atdec Flat panel steun SD-DO

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec SD-DO (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Component Checklist

Installation Instructions

A. Use this configuration with a

standard 50mm pole

(No inserts required)

B. Use this configuration with a

Visidec 42mm extrusion

pole

Use this configuration with a

standard 42mm pole

Step 1. Install Quickshift Donut

42mm Front

Donut Insert (x1)

Visidec Groove

Lock (x1)

42mm Rear

Donut Insert (x1)

5mm Allen

Key (x1)

Hardware Mounting

Screws

M4x10mm

Screw (x4)

M4x12mm

Screw (x4)

M4x16mm

Screw (x4)

Select your correct product configuration: A, B, or C.

Rear Donut

Insert

Rear Donut

Insert

Front Donut

Insert Front Donut

Insert

Groove

Insert

Check you have received all parts against this Component Checklist prior to installation.

Tightening

Tool (x1)

2mm Allen

Key (x1)

Slide the Quickshift Donut onto the pole

(with the lever open), removing the End

Cap if necessary.

Rear groove insert must align with slot in

the Pole.

(Visidec 42mm pole shown)

TIGHTEN

LOOSEN

Once in place, close the lever

to lock the Quickshift Donut

in the desired position.

Slide the Quickshift Donut into the desired position.

If necessary, adjust the tension between the

Quickshift Donut and the Pole using the 5mm Allen

Key supplied.

Slot

OR OR

Groove

Insert

Security

Screw (x1)

WARNING: Be careful not to overtighten

! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only.

! The Manufacturer accepts no responsibility for incorrect installation.

Display | Quickshift Donut

Quickshift

Donut (x1)

Note: Ensure inserts are fitted

in correct orientation.

Arrows point

to top surface

SD-DO

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.05.09 ©

Step 2. Remove VESA plate from Quickshift Donut

Step 5. Adjusting the VESA Ball Mount

Position your Display to the desired viewing angle, using the 40°

angular movement allowed by the VESA Ball Mount.

Depending on the weight of the display, it may be necessary to make

adjustments to the VESA Ball the display Mount. If does not hold its

position, or is too resistant, adjust the Tension Plate located at the

rear of the VESA Ball Mount (see diagram right).

To make any adjustments, use the Tightening Tool supplied.

Check the display, and then adjust again if necessary.

Installation Complete

Step 4. Attach your Display to the Quickshift Donut

Press and hold the Release Buttons (one on either side).

Release

Button

Whilst holding the Release Buttons, remove the VESA Plate.

LIFT

TIGHTEN

Hook the top of the VESA plate onto

the Quickshift Mount.

Insert the Security Screw, and tighten

using the 2mm Allen Key.

CLICK

Gently push the bottom of the Display

into the Mount until it ‘CLICKS’.

Back of Display

VESA Plate

Release

Buttons

Tightening

Tool

Tension

Plate

Loosen (-Kg)

Tighten (+Kg)

Step 3. Attach the VESA plate to your Display

There are two mounting hole configurations:

UÊÇxÊÝÊÇx

UÊ£ääÊÝÊ£ää

Choose appropriate Mounting Screws

from the Hardware supplied to suit

your Display. Top of

Display

Mounting Screws (x4)

VESA Plate

Back of Display

Çx

(3”) 100mm

(4”)

Çx

(3”)

100mm

(4”)

VESA plate

Product specificaties

Merk:	Atdec
Categorie:	Flat panel steun
Model:	SD-DO
Kleur van het product:	Zwart
Montagewijze:	Bureau
Maximale gewichtscapaciteit:	12 kg
Lengte:	150 mm
Draaihoek:	360 °
Pan bereik:	-40 - 40 °
Bereik kantelhoek:	-40 - 40 °
Bevestigingsstandaard:	VESA 75mm x 75mm, 100mm x 100mm, 200mm x 100mm