Amina Evolution AIW150E/S200 loudspeaker Handleiding

Amina Speaker Evolution AIW150E/S200 loudspeaker

Lees hieronder de 📖 handleiding in het Nederlandse voor Amina Evolution AIW150E/S200 loudspeaker (32 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/32

Installation Guide

V2.2 Aug 2015

Invisible Loudspeakers

AIW150i/350i/450i/550i/150i-S200/350i-S200

Products may vary from items pictured

Ensure that all installation mounting surfaces

are able to support the weight of the product.

After installation, avoid pushing on the wall

or ceiling surface immediately in front of the

speaker. Excessive excursion, whilst unlikely to

damage the speaker, will undoubtedly crack

the plaster around its perimeter.

Do not attempt to modify or repair the product.

Contact your distributor or manufacturer if a

fault should occur.

The rear of the product should not be subject

to chemical cleaning and should not be painted

in any way.

When plastering over, ensure only 2mm of

material covers the product. More than this will

degrade the performance of the product and

could lead to product failure.

To ensure optimal performance, please read

this guide carefully and keep in a safe place

for future reference.

Install this product in a cool, dry, clean place

- away from direct sunlight and heat sources,

strong vibrational forces, chemical fumes,

dust and moisture (steam).

Do not expose this product to sudden

temperature changes or locate it in an

environment with high humidity. This is to

prevent condensation forming inside which

may cause damage to the product.

Do not clean this product with chemical

solvents as this may damage the finish. Use a

clean, dry or damp cloth.

Caution: Read before installing this product

ENVIRONMENTAL:

Before installing, ensure that the building is environmentally sealed, de-humidified and at a stable

temperature of at least 16 degrees centigrade (61 degrees Fahrenheit)

Never force dry the environment after installing speakers. Force drying should only be used to

ensure the entire environment and structural work is fully dry before installation of invisible

loudspeakers.

This product should not be used with single thick coat plaster solutions or with other finishing

methods that take days (rather than hours) to dry out.

Only use low shrinkage plaster types to skim coat these loudspeakers. Consult your plaster

supplier for advice.

Excessive moisture can damage the product. For expert advice contact your dealer or Amina

Technologies Ltd.

Please be aware that when this product is directly fitted into a solid wall structure (e.g. when

using the solid wall backbox) vibrational energy is inevitably transferred into the solid wall

structure. This energy can travel for some considerable distance up, down and along the structure.

It is therefore recommended the product be fitted within acoustically insulated stud walls or

ceiling sections where possible. The use of the product directly embedded in solid walls is not

recommended in multi occupancy buildings.

Equally, using the product in simple (stud or rafter with plasterboard or floor board directly

attached on both sides) stud walls & wooden rafter ceiling/floor structures will also transfer

substantial sound energy to the other side of the wall or floor above. It is therefore recommended

that the product be fitted in acoustically isolated stud walls or ceiling sections where possible.

Completed and fully dried plaster surfaces should be finished with permeable coatings / materials

to allow moisture in that coating or the adhesives used to apply those materials, to dry into the

environment quickl y.

01 Message from the Managing Director

02 Included in the carton / Packaging

03 How to use this manual

04 Installation overview diagram

Section

Preparing the wall / ceiling and

fixing the product

05 Cavity Installation steps 1 + 2

06 Cavity Installation steps 3+4

07 Cavity Installation steps 5 + 6

08 Cavity Installation with backbox steps 1 + 2

09 Cavity Installation with backbox steps 3

10 Solid Wall Installation with backbox steps 1 + 2

11 Solid Wall Installation with backbox steps 3+4

12 Solid Wall Installation with backbox step 5

Section

Alignment and plastering preparation

13 Retrofit (patch plastered)

14 Retrofit (feathered skim)

15 Retrofit (full wet skim)

16 Drywall (patch plastered)

17 Drywall (feathered skim)

Section

Testing

18 Testing the speakers

Section

Finishing

19 Plastering and decorating steps 1 + 2

20 Plastering and decorating steps 3 + 4

21 Setup tips

22 Setup tips

23 Further details

24 Troubleshooting

25 Specifications / Evolution Series & APU

26 Spacesaver information

27 Accessories

28 Warranty & copyright information

29 Contact information

Contents

Product specificaties

Merk:	Amina
Categorie:	Speaker
Model:	Evolution AIW150E/S200 loudspeaker
Kleur van het product:	Beige,Black
Gewicht:	820 g
Breedte:	200 mm
Diepte:	40 mm
Hoogte:	450 mm
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Snelstartgids:	Ja
Garantiekaart:	Ja
Gemiddeld vermogen:	- W
Aanbevolen gebruik:	Universeel
Impedantie:	8 Ohm
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	1
Peak Music Power Output (PMPO):	30 W
Frequentiebereik:	105 - 20000 Hz
Gevoeligheid:	83 dB
Versterkeraansluiting (binding post):	Ja