Altronix ReServ2 Handleiding

Altronix UPS ReServ2

Lees hieronder de 📖 handleiding in het Nederlandse voor Altronix ReServ2 (8 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

Rev. 082510 More than just power.TM

Video Surveillance UPS

Installation Guide

Models Include:

ReServ1

- Twelve (12) true sine wave regulated 24VAC outputs and four (4) regulated 12VDC outputs.

- 4A total supply current @ 24VAC and 2A total supply current @ 12VDC.

- PTC protected power-limited outputs.

ReServ2

- Sixteen (16) true sine wave regulated 24VAC outputs.

- 4A total supply current.

- PTC protected power-limited outputs.

ReServ3

- Sixteen (16) regulated 12VDC outputs.

- 8A total supply current.

- PTC protected power-limited outputs.

- 2 - ReServ

Overview:

Altronix ReServ Video Surveillance UPS units are designed to provide power for 24VAC and/or 12VDC cameras

during normal or power outage conditions.

True sine wave regulated AC outputs and/or regulated DC outputs.

ReServ Series Video Surveillance UPS

Configuration Reference Chart:

Altronix

Model

Number

Output/Supply

Current (A)

Ambient

Temperature

Input

Rating

PTC Protected

Power-Limited Outputs

24VAC Outputs

12VDC Outputs

Agency

Listings

UL Listings and

File Numbers

ReServ1

24VAC @ 4A (100VA)

& 12VDC @ 2A -33º to 30ºC

115VAC

60Hz, 3.5A 16 12 4 UL File # E329542

UL 60950-1

UL/CUL Listed

for

Information

Technology

Equipment.

24VAC @ 3.5A (85VA)

& 12VDC @ 2A -33º to 42ºC

ReServ2

24VAC @ 4A (100VA) -33º to 30ºC 115VAC

60Hz, 3.5A 16 16 –

24VAC @ 3.5A (85VA) -33º to 42ºC

ReServ3 12VDC @ 8A -33º to 42ºC 115VAC

60Hz, 3.5A 16 –16

Specifications:

Output:

• PTC protected power-limited outputs rated @ 1A.

Battery Backup:

• Built-in charger for sealed lead acid or

gel type batteries.

• Automatic switchover to stand-by battery

when AC fails.

Supervision:

• AC fail supervision (form “C” contacts).

• Low battery supervision (form “C” contacts).

Visual & Audio Indicators:

• AC/DC power LED indicators.

• Individual power output LED indicators.

• Low voltage input and Shutdown LED indicators.

• Audio AC Fail and Battery Fail indicator.

Additional Features:

• True sine wave regulated AC outputs

(ReServ1 & ReServ2).

Regulated DC outputs (ReServ1 & ReServ3).

• Unit maintains camera synchronization.

• Ease of installation saves time and

eliminates costly labor.

Enclosure Dimensions :(H x W x D approximate)

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)

• Enclosure accommodates up to

two (2) 12VDC/7AH batteries.

Stand-by Specifications:

Stand-by Batteries

ReServ1 - 4A (100VA) load at 24VAC and 2A load at 12VDC max.

ReServ2 - 4A (100VA) max. load at 24VAC

ReServ3 - 8A (100VA) max. load at 12VDC

Two (2) 12VDC/7AH 45 minutes

Two (2) 12VDC/12AH 90 minutes

*When using 12AH batteries or larger a separate UL Listed battery enclosure must be installed.

Optional UL Listed battery enclosure must be mounted adjacent to the power supply via Class 1 wiring methods.

ReServ - 3 -

Installation Instructions:

This installation should be made by qualified service personnel and should conform to all local codes and in

accordance with the National Electrical Code. Product is intended for indoor use only. This product contains no

serviceable parts.

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes

in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place

the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower

two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s

upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws

. Secure enclosure to earth ground. (Enclosure Dimensions, pg. 8)

This product needs to be secured to the building before operation.Note:

2. Connect AC power mains to the terminals marked [L & N] .(Figs. 1-3, pg. 5-7)

Use 18 AWG or larger for all power connections (Battery, output) .(Figs. 1-3, pg. 5-7)

Use 18 AWG to 22 AWG for power-limited circuits (AC Fail/Low Battery reporting) .(Figs. 1-3, pg. 5-7)

A readily accessible disconnect device shall be incorporated in the building installation wiring.Note:

3. The LEDs on the power supply board will illuminate when AC power is present.

4. Measure output voltage before connecting cameras/devices to outputs. This helps avoiding potential damage.

5. ReServ3 only - Adjust voltage for every two (2) outputs using the corresponding trimpot(s) on the board

prior to connecting devices.

6. Connecting cameras/devices:

- Connect 12VDC cameras/devices to the terminals marked [P 1-4, N 1-4] .ReServ1 (Fig. 1, pg. 5)

Connect 24VAC cameras/devices to the terminals marked [5-16] .(Fig. 1, pg. 5)

- Connect 24VAC cameras/devices to the terminals marked [1-16] .ReServ2 (Fig. 2, pg. 6)

- Connect 12VDC cameras/devices to the terminals marked [P 1-16, N 1-16] .ReServ3 (Fig. 3, pg. 7)

7. Connect batteries to the terminals marked [+ BAT –] . (Figs. 1-3, pg. 5-7)

Use two (2) 12VDC batteries connected in series for 24VDC operation (battery leads included).

Use batteries - Casil CA1270 (12V/7AH), Genesis NP7-12 (12V/7AH), Ultratech UT1270 (12V/7AH).

8. Connect appropriate signaling notification devices to AC FAIL & BAT FAIL (Figs. 1-3, pg. 5-7)

supervisory relay outputs.

9. The power LEDs on the unit for Outputs 1-16 will illuminate when AC power is present . (Figs. 1-3, pg. 5-7)

If any of the power LEDs are not illuminated, the cause may be due to the following:Note:

a. AC mains and battery fail.

b. One (1) or more power output PTCs are tripped due to a short circuit or overload condition.

c. Unit damaged/defective.

To reset the PTC:

1. Disconnect corresponding camera/device connected to terminals marked [1-16] .(Figs. 1-3, pg. 5-7)

2. Eliminate the trouble condition (short circuit or overload).

3. Allow 1 minute for PTC to cool off (reset).

4. Connect corresponding cameras/devices to terminals marked [1-16] .(Figs. 1-3, pg. 5-7)

5. Power LEDs will illuminate indicating power has been restored to outputs .(Figs. 1-3, pg. 5-7)

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or

moisture. This installation should be made by qualified service personnel and should conform

to the National Electrical Code and all local codes.

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the

user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that

may be of sufficient magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying

the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure.

There are no user serviceable parts inside.

Refer servicing to qualified service personnel.

Product specificaties

Merk:	Altronix
Categorie:	UPS
Model:	ReServ2
Kleur van het product:	Grijs
Gewicht:	3674 g
Breedte:	330 mm
Diepte:	83 mm
Hoogte:	343 mm
Gewicht verpakking:	4105 g
LED-indicatoren:	Ja
Certificering:	UL 60950-1\nCE
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	- W
Frequentie:	60 Hz
Bedrijfstemperatuur (T-T):	-33 - 30 °C
Aantal AC uitgangen:	16 AC-uitgang(en)
Nominale input voltage:	115 V
Output power capacity:	- kVA
Ingang operation voltage (min):	- V
Ingang operation voltage (max):	- V
Uitgang operation voltage (min):	24 V
Uitgang operation voltage (max):	24 V
Typische backup tijd op halve lading:	- min
Typische backup tijd op volledige lading:	- min