Alto ZMX122FX Handleiding

Alto Mengpaneel ZMX122FX

Lees hieronder de 📖 handleiding in het Nederlandse voor Alto ZMX122FX (20 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20

QUICKSTART GUIDE

ENGLISH ( 2 – 4 )

MANUAL DE INICIO RÁPIDO

ESPAÑOL ( 5 – 7 )

GUIDE D’UTILISATION RAPIDE

FRANÇAIS ( 8 – 10 )

GUIDA RAPIDA

ITALIANO ( 11 – 13 )

SCHNELLSTART-ANLEITUNG

DEUTSCH ( 14 – 16 )

SNELSTARTGIDS

NEDERLANDS ( 17 – 19 )

2 T K

2 TK

vo lume

p itch x y z

octave

accomp storetap

phrase latch

ana l o g m o d e l in g sy nt h

pus

BOX CONTENTS

y ZEPHYR mixer

y Power adapter

y Quickstart Guide

y Safety Instructions & Warranty Information booklet

CONNECTION DIAGRAM

Power

House Speakers*

Monitors*

Keyboard*

Drum Machine*

Microphones*

Headphones* External effects rack,

compressor, etc.*

Notes:

y Microphones, monitors, amplifier, speakers, cables, etc. are not included.

y To reduce electrical hum at high gain settings, keep the mixer's power supply away from your guitar cable and the

mixer's channel inputs.

y To use an external effects rack unit, compressor, etc., use a Y-cable (1/4" stereo to two 1/4" mono) to connect the AUX

SEND "2 FX" output to the left and right inputs your external device. Connect the outputs of your external device to the

left and right AUX RETURN INPUTS.

* not included

FEATURES

1. POWER IN – Use the included power

adapter to connect the mixer to a power

outlet. While the power is switched off,

plug the power supply into the mixer

first, then plug the power supply into a

power outlet.

2. POWER SWITCH – Turns the mixer on

and off. Turn on the mixer after all

input devices have been connected and

before you turn on amplifiers. Turn off

amplifiers before you turn off the mixer.

3. FOOTSWITCH – When a latching-style

footswitch is connected to this jack with

a 1/4" TRS cable, it can be pressed to

allow all channels to bypass the mixer's

internal effects processor.

4. MIC INPUT – Connect a microphone to

these inputs with an XLR cable.

5. LINE INPUT * – Connect line-level

devices to these inputs with 1/4" cables.

6. GAIN – Adjusts the channel audio level

(pre-fader and pre-EQ gain). Adjust

this so that the PEAK LED just barely

lights up during the loudest parts of the

song.

7. HI EQ (TREBLE) – Adjusts the high

(treble) frequencies of the channel.

8. MID EQ – Adjusts the mid-range

frequencies of the channel.

9. LOW EQ (BASS) – Adjusts the low

(bass) frequencies of the channel.

10. AUX SEND 1 MON – Adjusts the

channel audio (pre-EQ) level that is

sent to the AUX SEND output labeled

"1 MON." You can use this to create a

custom monitor mix for yourself or your musicians.

11. AUX SEND 2 FX – Adjusts the channel audio (post-EQ) level that is sent

to the mixer's internal effects processor. Turn this up for the channels that

you want internal effects applied to. You can use this to apply external

effects to individual channels.

12. CHANNEL PAN – Adjusts the (mono) channel's position in the stereo

field.

13. BALANCE (CH 5/6 & 7/8) – Adjusts the balance between Channels 5 and

6 and Channels 7 and 8.

14. PEAK LED – The LED will flash if the signal is clipping. If this happens,

decrease the setting of the GAIN knob or CHANNEL VOLUME knob.

15. CHANNEL VOLUME – Adjusts the audio level on the channel.

16. AUX RETURN INPUTS ** – You can connect the outputs of an external

device to these inputs with 1/4" mono cables. This is usually used for

outboard effects devices but can also be used like an extra input channel

for synthesizers, drum machines, etc. If your source is mono, plug it into

the left jack and it will be heard on both the left and right sides.

17. AUX SEND OUTPUTS ** – You can use a 1/4" TRS cable to connect the

AUX 1 MON output to the input of an external amplifier or active monitor to create a custom monitor mix for onstage

musicians. You can adjust this level with the AUX RETURN LEVEL knob labeled "TO AUX 1 MON." To use an external

effects rack unit, compressor, etc. with the mixer, you can use a Y-cable to connect the AUX 2 FX output to the input of

your external device, then connect the outputs of the device to the AUX RETURN INPUTS of the mixer.

18. 2-TRACK INPUTS – You may connect these inputs to the outputs of an external sound source using a standard stereo

RCA cable (sold separately). You can send this channel to the monitor mix (using the MAIN/2-TRACK switch) and/or

the main mix (using the 2-TRACK TO MAIN switch).

19. 2-TRACK OUTPUTS – You may connect these outputs to the inputs of an external recording device using a standard

stereo RCA cable (sold separately).

20. CTRL ROOM OUTPUTS – Use standard 1/4" cables to connect these outputs to your monitor or amplifier system. The

level of these outputs is controlled by the CTRL ROOM / PHONES knob.

21. MAIN MIX OUTPUTS – Use standard 1/4" cables to connect these outputs to the house speaker or amplifier system.

The level of these outputs is controlled by the MAIN VOLUME knob.

22. PHONES – Connect your 1/4" stereo headphones to this output. The CTRL ROOM / PHONES knob controls the

volume.

* When using LINE INPUTS 5/6, 7/8,

and the AUX RETURNS:

• If only the left channel is used, the

signal will be heard in both left and

right channels and the balance will

not be adjustable.

• If only the right channel is used, the

signal will be heard in the right

channel only.

** To use an external effects rack unit,

compressor, etc., use a Y-cable (1/4"

stereo to two 1/4" mono) to connect the

AUX SEND "2 FX" output to the left and

right inputs your external device.

Connect the outputs of your external

device to the left and right AUX

RETURN INPUTS.

2 T K

5 5

12 13 13

1617

17 18

2020 21

31 32

Product specificaties

Merk:	Alto
Categorie:	Mengpaneel
Model:	ZMX122FX
Gewicht:	2300 g
Breedte:	256 mm
Diepte:	250 mm
Hoogte:	72 mm
Videomogelijkheid:	Nee
Equalizer-instellingen:	Ja
Frequentiebereik:	20 - 22000 Hz
Aantal banden equalizer:	3
D/A-converter:	24-bit
Aantal kanalen:	8 kanalen
Totale harmonische vervorming (THD):	0.005 procent
Microphone input impedance:	3900 Ohm
Stroomverbruik (typisch):	27 W
Digitaal geluid verwerken:	24 Bit