Adder CATx Dual CAM Handleiding

Adder Niet gecategoriseerd CATx Dual CAM

Lees hieronder de 📖 handleiding in het Nederlandse voor Adder CATx Dual CAM (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TO LO CAL PO WER

www.ad de r.co m

The two variants of the CATX Dual Access Module are highly compact devices that allow you to share a single

computer between two sets of peripheral devices. The CATX-USB-DA variant is not ﬁtted with audio or serial

ports but is otherwise identical to the CATX-USBA-DA model.

The module connects to various ports on your computer. You then connect it via CAT 5, 5e or 6 cabling to

AdderView CATx KVM switches and/or Adder extender receivers (either AdderLink X2 Silver or X200), each of

which can be located up to 300 metres from the module. Your video displays, keyboard, mice and speakers

are linked to the remote devices.

The CATX Dual Access Module uses a USB port to derive its power from the host computer, dispensing with

the need for a separate power supply and thus simplifying installation.

CATX Dual Access Module

Quick Start (CATX-USBA-DA and CATX-USB-DA)

Adder Technology Limited,

Technology House,

Trafalgar Way, Bar Hill,

Cambridge, CB23 8SQ,

United Kingdom

Tel: +44 (0)1954 780044

Fax: +44 (0)1954 780081

All trademarks are acknowledged. Documentation by Corporate Text & Design (www.ctxd.com)

Adder Corporation,

350R Merrimac Street,

Newburyport,

MA 01950,

United States of America

Tel: +1-888-932-3337

Fax: +1-888-275-1117

support@adder.com

www.adder.com

Safety information

• For use in dry, oil free indoor environments only.

• Do not use to link between buildings.

• Not suitable for use in hazardous or explosive

environments or next to highly ﬂammable

materials.

• Ensure that all twisted pair interconnect cables

are installed in compliance with all applicable

wiring regulations.

• Do not connect the CATx link interface (RJ45

style connector) to any other equipment,

particularly network or telecommunications

equipment.

• Where possible, avoid laying the twisted pair

link cable(s) alongside power cables.

• Do not attempt to service the module yourself.

• The modules do not provide ground isolation

and should not be used for any applications

that require ground isolation or galvanic

isolation.

• For correct operation, the transmitter

and receiver modules must have ground

connections. At the computer end, this is

achieved by ensuring that the computer that

the module is connected to has a ground

connection. At the audio/visual device end, this

can be achieved by ensuring that the power

supply is connected to a grounded power

outlet. Alternatively, a ground connection will

be made via the monitor, if the monitor is itself

grounded.

Warranty

Adder Technology Ltd warrants that this product

shall be free from defects in workmanship and

materials for a period of two years from the date

of original purchase. If the product should fail to

operate correctly in normal use during the warranty

period, Adder will replace or repair it free of charge.

No liability can be accepted for damage due to

misuse or circumstances outside Adder’s control.

Also Adder will not be responsible for any loss,

damage or injury arising directly or indirectly from

the use of this product. Adder’s total liability under

the terms of this warranty shall in all circumstances

be limited to the replacement value of this product.

If any difﬁculty is experienced in the installation or

use of this product that you are unable to resolve,

please contact your supplier.

CATX Dual

Access Module

What you may additionally need

What’s in the box

Adder Asia Pacic

6 New Industrial Road,

Hoe Huat Industrial Building

#07-01,

Singapore 536199

Tel: +65 6288 5767

Fax: +65 6284 1150

AdderView CATx

KVM switch

CAT 5, 5e or 6 link

cables, up to 300m

in length

* Not tted on

CATX-USB-DA

models

LOC REM OSD UPG LCK PWR

www .add er

.co m

AdderLink X2 Silver or

X200 extender receiver

INDOOR USE ONLY

3 2 1

765

COMPUTER CONNECTIONS

Audio

USB

Video

Serial port

AdderView KVM switch

AdderLink X2 Silver or X200 receiver

234

TO LOCAL

POWER

Resolutions and cable lengths

The maximum resolutions achievable are:

1600 x 1200 x 60Hz at 200m and

1280 x 1024 x 60Hz at 300m.

Do not exceed 300m cable lengths in any

installation.

Host computer connections

The module does not require a power adapter

because it derives all of its power from the host

computer. Therefore the USB cable must always

be connected to a USB port on the computer that

is capable of providing up to 500mA.

Receiver unit connections

You can connect two AdderView KVM switches, two AdderLink X2

Silver extenders or a mixture of both.

For details about connections at the receiver units, please refer to

the guides for those devices.

Disabling/re-enabling receiver connections

When required, a user of one remote link can disable (and re-

enable) the other remote link using serial port commands (this

feature is available only on the CATX-USBA-DA models). To do

this you need to determine two things: a) The Com port to which

the serial connector is attached and b) which of the two remote

ports you are using (A or B). See also ‘Serial port conﬁguration’.

1 From one of the remote keyboards, open a terminal program

on the computer and use it to send the appropriate character

to the Com port to which the module is attached:

Port Disable character Enable character

A (0x61) (0x41)a A

B (0x62) (0x42) b B

The module will return OK or FAIL to indicate the result.

Note: Take care not to disable the port that you are using. If

you do, either re-power the module or use the other remote

link to re-enable your link.

2 Re-enable the port when it is appropriate. Note: Whenever

the module is re-powered, both links will always be enabled.

EDID display information

The module contains a default set of EDID information that

supports display resolutions up to 1600 x 1200 @ 60Hz. In

addition, the module will check during power up whether

alternative EDID information is available from the KVM switch or

extender that is connected to port A. If required, you can also

harvest and store new EDID information from your display or an

Adder DDC Ghost device.

User arbitration

Control of the host computer is arbitrated by the

module on a ﬁrst come, ﬁrst served basis. At the moment that

a key is pressed or a mouse is moved by a user, the keyboard and

mouse of the other user are temporarily locked-out (the video images

remain). The keyboard indicators of the locked-out user then begin to ﬂash to

conﬁrm their status. After two seconds of inactivity from the user currently in

control, the module returns to its idle condition and re-instates the keyboard

indicators of the locked-out user.

* Not tted on

CATX-USB-DA

models

Serial port conﬁguration

The module can automatically alter its baud rate to match that

of the host computer’s serial port. To do this the other serial

parameters must ﬁrst be correct: 8 data bits, no parity, 1 stop

bit and no hardware handshaking. These are usually the default

settings, however, if you do need to alter them, open the Windows

Device Manager, locate the entry for the COM port to which the

module is connected and view the Properties > Port Settings tab.

Once set, open a terminal program and send a Return (carriage

return) to the Com port to which the module is attached until the

message is returned. The USB Dual Access CAM version 1.00

module can now accept commands.

Product specificaties

Merk:	Adder
Categorie:	Niet gecategoriseerd
Model:	CATx Dual CAM
Kleur van het product:	Zwart
Aantal USB 2.0-poorten:	1
VGA (D-Sub)poort(en):	1
RS-232 port:	1
Maximaal bereik:	300 m
Code geharmoniseerd systeem (HS):	84733020