ADATA SWORDFISH Handleiding

ADATA Solid state drives (ssd) SWORDFISH

Lees hieronder de 📖 handleiding in het Nederlandse voor ADATA SWORDFISH (4 pagina's) in de categorie Solid state drives (ssd). Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

INSTALLING A M.2 SSD

ON A LAPTOP PC

BEFORE INSTALLATION

1. GATHER THE THINGS YOU'LL

NEED

*Please use a standard Phillips screwdriver (3.5mm) for

disassembling the case; and a smaller Phillips

screwdriver for installing the M.2 solid state drive as it

uses screws with a diameter of 1.85-1.98mm.

PC, Phillips screwdrivers, and ADATA M.2 SSD

2. BACK UP YOUR DATA

Make sure to backup the important data on

your PC to an external device, such as an

external HDD, before starting installation.

3. POWER OFF YOUR PC

After backing up your data, power off your PC

to avoid data loss or damage to other

components during installation.

4. UNPLUG POWER CORD AND

BATTERY

*The battery removal step applies only to laptops when

it's possible to remove the battery. To see how to

remove the battery, refer to your user manual.

This action is necessary to discharge residual

power that can damage your PC and its

components.

*If you are unsure how to do this, refer to your user

manual

*The location of slots may vary by PC. Please check

your PC's user manual for more information.

**Generally speaking, the screws that secure the SSD in

place will be installed on the motherboard when the

laptop is shipped from the factory.

*The slot has a foolproof design. Please insert the SSD

in the direction corresponding to the pins on the solid

state drive and the slot. Do not insert it forcibly to avoid

damage to the product.

INSTALLATION

Use your standard Phillips screwdriver to

remove the screws from the back plate.

2. LOCATE THE M.2 PCIE SLOT AND

CONFIRM THERE ARE SCREWS

Locate the M.2 PCIe slot, ensure the SSD will fit

and confirm there are screws present.

3. ALIGN THE M.2 SLOT AND INSERT

THE SOLID STATE DRIVE

Use your small Phillips screwdriver to remove

the screws on the motherboard. Align the

notches in the SSD with the ridges in the PCIe

slot, then insert at a an angle. Give it a final

push to ensure it is securely in place.

FASTEN THE SCREWS TO SECURE

THE SSD

*Do not overtighten the screws

Use your small Phillips screwdriver to secure

the SSD into place.

1. REMOVE YOUR PC'S BACK PLATE

Product specificaties

Merk:	ADATA
Categorie:	Solid state drives (ssd)
Model:	SWORDFISH
Gewicht:	10.5 g
Breedte:	80 mm
Diepte:	3.85 mm
Hoogte:	22 mm
Minimum operationele temperatuur:	0 °C
Maximale temperatuur (in bedrijf):	70 °C
Certificering:	CE, FCC, BSMI, KC
Interface:	PCI Express 3.0
Duurzaamheidscertificaten:	RoHS
Ondersteunde beveiligingsalgoritmen:	256-bit AES
Temperatuur bij opslag:	-40 - 85 °C
SSD capaciteit:	2000 GB
ECC:	Ja
SSD-vormfactor:	M.2
Mean time between failures (MTBF):	1800000 uur
Type geheugen:	3D NAND
Leessnelheid:	1800 MB/s
Schrijfsnelheid:	1200 MB/s
Component voor:	PC/notebook
Schokbestendigheid:	1500 G
Bedrijfstemperatuur (T-T):	0 - 70 °C
Code geharmoniseerd systeem (HS):	84717070
Hardware encryptie:	Ja
NVMe:	Ja
NVMe versie:	1.3
Random read (4KB):	180000 IOPS
Random write (4KB):	180000 IOPS
PCI Express interface data lanes:	x4
TBW-classificatie:	960
Sequentiële leessnelheid (ATTO):	1800 MB/s
Sequentiële schrijfsnelheid (ATTO):	1400 MB/s
Sequentiële leessnelheid (AS SSD):	1700 MB/s
Sequentiële schrijfsnelheid (AS SSD):	1100 MB/s
Sequentiële leessnelheid (CDM):	1800 MB/s
Sequentiële schrijfsnelheid (CDM):	1200 MB/s