Acti A951 Handleiding

Acti Niet gecategoriseerd A951

Bekijk gratis de handleiding van Acti A951 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 25 mensen en kreeg gemiddeld 4.4 sterren uit 13 reviews. Heb je een vraag over Acti A951 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/2

A951 Outdoor Speed Dome Camera Quick Installation Guide

This guide is for quick installing and connecting A951 Outdoor Speed Dome Camera. For more details, please refer to

the Hardware Manual.

Installation Notices

 This camera must be installed by qualified personnel and the installation should conform to all local codes.

 Do not replace batteries of the camera. Risk of explosion may occur if the battery is replaced by an incorrect type.

 To use an external power supply, please contact the camera manufacturer to confirm that the power supply

complies with the requirements and shares the same power specifications with the camera.

 For safety concern, please hook up the camera with the anti-drop chain of the

pendant when installing the camera. For more information about mounting

accessories, please contact Sales.

Camera’s Connectors

No.

Connector

Definition

Remarks

Reset Button

Press the button with a proper tool for at least 20 seconds to restore the system.

RJ-45 Port

For network and UPoE connections

#Please contact the manufacturer for

compatible PoE injector.

Power (AC24V)

AC24V power connection

Alarm I/O

& RS-485 Connector*

Alarm I/O

& RS-485 connection

# Do NOT connect external power supply to

the alarm I/O connector of the camera.

Memory Card Slot

Insert the memory card into the card slot to store videos and snapshots. Do not

remove the memory card when the camera is powered on.

NOTE: It is not recommended to record with the memory card for 24/7 continuously, as it may not be able to

support long term continuous data read/write. Please contact the manufacturer of the memory card for

information regarding the reliability and the life expectancy.

Power Connection

To power up the camera, connect the bundled AC24V power adaptor to the power connector of the camera and the

power outlet. Refer to the diagram and pin definition below.

Definition

Terminal Block Label

Power Adaptor Cable

AC24V L

AC2

Blue

GND

Ground

Green-Yellow

AC24V N

AC1

Brown

Alternatively, users can use an Ethernet cable and connect it to the RJ-45 port of the camera and a UPoE 60W

switch.

Ethernet Cable Connection

Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to

the network switch or PC.

NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the

PC.

NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check

the LAN connection.

Green Link Light indicates good network connection.

Orange Activity Light flashes for network activity indication.

NOTE: The ITE is to be connected only to PoE networks without routing to the outside plant or equivalent

description.

AIarm I/O & RS-485 Connection

Please refer to the diagram and pin definition tables below for audio/alarm I/O & RS-485 connection.

Definition

N/A

Alarm Out B1

Alarm In 4

GND (Alarm I/O and RS-485)

GND (Audio I/O)

Alarm Out B2

Alarm In 3

N/A

Alarm Out A1

RS-485 D+ (Optional)

Alarm In 2

Alarm Out A2

RS-485 D- (Optional)

Alarm In 1

V20210727

Before Login to the Camera

A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the

camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and

plug-ins or setting Internet’s security level to default. For further details, please refer to the Hardware Manual.

ActiveX Controls and Plug-ins Settings

Internet Security Level

Step 1: Start the Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of the

browser. Then click on <Internet Options>.

Step 3: Click on the <Security> tab and select

<Internet>, and click on <Custom level> to

change ActiveX settings.

Step 4: Set “ActiveX controls and plug-ins” items to

<Prompt> or <Enable>.

Step 1: Start the IE Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of the

browser. Then click on <Internet Options>.

Step 3: Click on the <Security> tab and select

<Internet>.

Step 4: Down the page, click on <Default Level> and

<OK> to confirm the setting. Close the browser

window, and open a new one later for

accessing the IP camera.

NOTE: It is strongly recommended using Microsoft Internet Explorer 10.0 or later version to connect the

camera.

Camera Login

The default IP address of the camera is: 192.168.0.100. Therefore, to access the camera for the first time, please set

the IP address of the PC as: 192.168.0.XXX; for example:

IP Address: 192.168.0.99

Subnet Mask: 255.255.255.0

 Type in corresponding camera IP address into the URL field on the web browser and hit "Enter".

 For initial login, use the default username: “admin” and then setup the password. Follow the on-screen instructions

to do so. This username and password will be used for succeeding login. Note that the username and password

are case sensitive.

Default Username: admin Password: (user must set up first)

Install the ActiveX Control

 After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.

 Right click on the information bar and click on <Install ActiveX Control…> to permit ActiveX control installation.

 In the pop-up security warning window, click on <Install> to start downloading the software on the PC.

 Click on <Finish> after installation is completed.

Browser-based Viewer

The main page of the IP camera user interface,

as shown.

To activate the wiper, click the <Wiper>

icon located on the function buttons of the

<Home> page.

A951

Outdoor Speed Dome Camera

Quick Installation Guide

Product specificaties

Merk:	Acti
Categorie:	Niet gecategoriseerd
Model:	A951
Kleur van het product:	Wit
Gewicht:	8900 g
Hoogte:	431 mm
Soort:	IP-beveiligingscamera
Materiaal behuizing:	Metal, Plastic
Internationale veiligheidscode (IP):	IP66
Bluetooth:	Nee
Ondersteund audioformaat:	AAC, PCM
Stemcodecs:	G.711, G.726
Vormfactor:	Dome
Automatisch scherpstellen:	Ja
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond/muur
Maximum resolutie:	3840 x 2160 Pixels
Totaal aantal megapixels:	8 MP
Videocompressieformaten:	H.264, H.265, M-JPEG
Diameter:	284 mm
Type stroombron:	AC, PoE
Minimale belichting:	0.02 Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSDHC, MicroSDXC
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Video bewegings-detectie:	Ja
HTTPS-encryptie:	Ja
Audiosysteem:	2-weg
Zoomcapaciteit:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Brandpuntbereik:	6.5 - 202 mm
Wachtwoordbeveiliging:	Ja
Vermogensverbruik (max):	55 W
Certificering:	CE, FCC
Omvang optische sensor:	1/1.8 "
Beeldstabilisator:	Ja
Type beeldsensor:	CMOS
Optische zoom:	31 x
Camera sluitertijd:	1-1/10000 s
Type camerasluiter:	Elektronisch
Password bescherming:	Gebruiker
Ondersteunde grafische resoluties:	1280 x 720 (HD 720), 3840 x 2160
Ruisonderdrukking:	Ja
Netwerkstandaard:	IEEE 802.1x
Maximaal 30 frames per seconde:	30 fps
Ondersteunde netwerkprotocollen:	IPv4/v6, TCP, UDP, DHCP, PPPoE, HTTP, HTTPS, DNS, DDNS, NTP, RTP, RTSP, SMTP, FTP, IGMP, ICMP, ARP, UPnP, QoS, SNMP, IEEE 802.1X
IP-adresfilter:	Ja
Progressive scan:	Ja
Ethernet interface type:	Gigabit Ethernet
Quality of Service (QoS):	Ja
PTZ control:	Ja
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
Aantal lenzen:	1
Maximum aperture number:	1.55
Controle camerapanning:	Ja
Kantelfunctie camera:	Ja
Draai-snelheid:	300 °/sec
Vooringestelde snelheid pan:	300 °/sec
Aantal sensoren:	1
Videostreaming:	Ja
Weerbestendig:	Ja
Nachtkijker afstand:	100 m
Infrarood (IR)-afsluitingsfilter:	Ja
Aantal effectieve pixels (H x V):	3864 x 2180 Pixels
Vooraf ingestelde punten:	Ja
Aanpassing van de afbeeldingskwaliteit:	Brightness, Contrast, Sharpness
Stroomverbruik (voeding via Ethernet (PoE)):	51 W
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
AC-ingangsspanning:	24 V
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Bereik kantelhoek:	-10 - 100 °
Aanpassing sluitertijd:	Auto
Privézone maskeren:	Ja
Systeemfuncties intelligente videobewaking (IVS):	Gezichtsherkenning
Kijkhoek lens, horizontaal:	63.4 °
Type waarschuwingsnotificatie:	E-mail
Ruisonderdrukkingstechnologie:	3D-ruisonderdrukking
Kijkhoek lens, verticaal:	37.8 °
Tekstoverlay:	Ja
PTZ-modi:	Automatisch scannen