Zurn Z1203-ND4 Handleiding

Bekijk gratis de handleiding van Zurn Z1203-ND4 (2 pagina’s), behorend tot de categorie Toilet. Deze gids werd als nuttig beoordeeld door 10 mensen en kreeg gemiddeld 4.1 sterren uit 3 reviews. Heb je een vraag over Zurn Z1203-ND4 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

®

Z1203 thru Z1207

INSTALLATION INSTRUCTIONS

Form #C9Date:05/13/11C.N. No.121287Rev.F

Page 1 of 2

ZURN INDUSTRIES, LLC

♦♦

♦♦

♦ SPECIFICATION DRAINAGE OPERATION

♦♦

♦♦

♦ 1801 Pittsburgh Ave.

♦♦

♦♦

♦ Erie, PA 16514

Phone: 814/455-0921

♦♦

♦♦

♦ Fax: 814/454-7929

♦♦

♦♦

♦ World Wide Web: www.zurn.com

In Canada: ZURN INDUSTRIES LIMITED

♦♦

♦♦

♦ 3544 Nashua Drive

♦♦

♦♦

♦ Mississauga, Ontario L4V1L2

♦♦

♦♦

♦ Phone: 905/405-8272 Fax: 905/405-1292

1

Lay out all necessary closet

fittings on floor. To obtain spacing

between units, place proper lengths of

pipe between adjoining fittings

(or use ZE-Series).

2

Lift lengths of pipe into place

between closet fittings and make

up joints being sure all faces of fittings

are parallel.

3

Roll entire assembly of connected

closet fittings and drainage pipe

180° so that the flat faces are facing

upward.

4

Place gasket on faces of fitting.

Bolt face plate ontofitting, making certain to hand-tighten the four bolts.

Beginning with the nearest fitting stack, locate top of large opening in face plate to

coincide with top of oval waterway in closet fitting. (The opening on successive

fittings should be located at successively lower positions to maintain proper

drainage pitch). Using wrench, tighten all bolts uniformly until gasket is sufficiently

compressed.

5

(Omit this step when installing non-adjustable ZF carrier)

Adjust and secure feet on each faceplate, to bring closet outlet to desired

closet height.

6

Roll entire assembly 90° forward onto feet, move intoposition, level, align,

and make stack connection. Check to be sure closet outlets are in correct

position and true. Secure feet to floor using rear slots (slots on fitting side of foot,

not coupling side) and 1/2 [13] bolts (supplied by others).

6a

(Omit this step when installing double carrier)

At this point, install the rear anchor foot assembly. To assemble, screw

stud into cast foot and secure with locknut, attach top of stud to anchoring lug on

backside of carrier using locknuts and washers, then securely fasten cast foot to

floor using 1/2 [13] bolts (supplied by others).

Note:

For concealed flush valves

and wall closets with rear

inlet supply, face plate

must be located behind

supply line to prevent

interference of face plate

with supply line.

Rigid Blow Out System

AKL

I.P.S.Min.Max.

4[102]6 1/8[156]2[51]4 1/4[108]

5[127]6 5/8[168]1 1/2[38]3 3/4[95]

* Min. "P" Dim = 2 [51]

Flange is tapped to receive

3/8 [10] studs as required for

floor style back outlet closet.

All necessary 3/8 [10] studs,

nuts, washers and chrome

plate trim are furnished with

assembly.

-F Option

Floor Style Back Outlet Closet System

Product specificaties