Yamaha VC4B Handleiding

Yamaha Speaker VC4B

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha VC4B (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe place for future reference.

This product is a speaker system designed for background music and public address

applications in places such as stores, restaurants and other commercial spaces.

Do not use for any purposes other than the one intended. Those who are

unfamiliar with handling or those who can not handle according to this manual,

should be supervised by responsible persons to ensure safety.

Always consult a professional installer if the product installation requires

construction work.

WARNING

Always follow the basic precautions listed

below to avoid the possibility of serious

injury or even death from electrical shock,

short-circuiting, damages, fire or other

hazards. These precautions include, but

are not limited to, the following:

If you notice any abnormality

• If any of the following problems occur,

immediately turn off the power of the amplifier.

- Unusual smells or smoke are emitted.

- Some object, or water has been dropped

into the product.

- There is a sudden loss of sound during use

of the product.

- Cracks or other visible damage appear on

the product.

Then have the product inspected or repaired

by qualified Yamaha service personnel.

Do not open

• This product contains no user-serviceable

parts. Do not attempt to disassemble the

internal parts or modify them in any way.

Water warning

• Do not expose the product to rain, use it near

water or in damp or wet conditions.

Fire warning

• Do not place any burning items or open flames

near the product, since they may cause a fire.

Hearing loss

• Before turning the power of all devices on or off,

make sure that all volume levels are set to the

minimum. Failing to do so may result in hearing

loss, electric shock, or device damage.

• When turning on the AC power in your audio

system, always turn on the power amplifier

LAST, to avoid hearing loss and speaker

damage. When turning the power off, the

power amplifier should be turned off FIRST for

the same reason.

Location and connection

• Always consult a professional installer if the

product installation requires construction work, and

make sure to observe the following precautions.

- Choose mounting hardware and an

installation location that can support the

weight of the product.

- Avoid locations that are exposed to constant

vibration.

- Use the required tools to install the product.

- Inspect the product periodically.

• Do not place the product in an unstable

position or a location with excessive vibration,

where it might accidentally fall down and cause

injury.

CAUTION

Always follow the basic precautions listed

below to avoid the possibility of physical

injury to you or others. These precautions

include, but are not limited to, the

following:

Location and connection

• Keep this product out of reach of children. This

product is not suitable for use in locations

where children are likely to be present.

• Do not place the product in a location where it

may come into contact with corrosive gases or

salt air. Doing so may result in malfunction.

• Use only speaker cables for connecting

speakers to the speaker jacks. Use of other

types of cables may result in fire.

Handling caution

• Do not insert your fingers or hands in any gaps

or openings on the product (clamps or moving

parts on the rails).

• Do not rest your weight on the product or place

heavy objects on it.

• When choosing a power amplifier for use with

this product, make sure that the output power

of the amplifier meets the following conditions:

- When using a low-impedance connection,

make sure that the output power of the

amplifier is lower than the power capacity of

this product.

- When using a high-impedance connection,

be sure that the total rating of the transformer

taps of the speakers does not exceed the

output power of the amplifier.

If the output power is not appropriate,

malfunction or fire may occur.

• Do not input excessively loud signals that may result

in clipping in the amplifier or cause the following:

- Feedback, when using a microphone

- Continuous and extremely loud sound from a

musical instrument, etc.

- Continuous and excessively loud distorted

sound

- Noise caused by plugging/unplugging the

cable while the amplifier is turned on

Even if the output power of the amplifier is

lower than the power capacity of this product

(program), damage to the product,

malfunction or fire may occur.

PA_en_12

General Specifications

Unpacking

Unpack the contents and confirm that

all the following items are included.

• Speaker × 1

• Grille × 1

• Safety wire × 1

• Cutout template × 1

• Owner’s Manual (this manual)

* Speaker cable is not included.

The following Reinforcing Bracket

Kit is included only with VC8B,

VC8W, VC6B, VC6W.

• Tile rails × 2

• C-ring × 1

• Screws (S-TITE M4, 8 mm) × 2

Optional Items (sold separately; VC4B and VC4W only)

Reinforcing Bracket Kit (AB-C2)

Bundled Items

• Tile rails × 2

• C-ring × 1

• Screws (S-TITE M4, 8 mm) × 2

* In this manual, the installation method using the AB-C2 Reinforcing Bracket Kit

is also explained.

Material and weight of the Reinforcing Bracket Kit (AB-C2): steel, 1.0 kg

*1 : Half-space (2π)

*2 : Calculated based on power rating and sensitivity

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download

the manual file.

The dimensions are shown in “Dimensions” on the back side of the manual.

VC4B VC4W VC6B VC6W VC8B VC8W

System Type 2way Coaxial type, Acoustic Suspension

Components HF 0.8" film dome 0.8" soft dome 1" soft dome

LF 4" (10 cm) cone 6.5" (16 cm) cone 8" (20 cm) cone

Nominal Impedance 16 Ω

Frequency Range *1 (-10 dB) 121 Hz - 20 kHz 104 Hz - 20 kHz 96 Hz - 20 kHz

Coverage Angle *1 160° conical 120° conical 110° conical

Power Rating NOISE 15 W 25 W 25 W

PGM 30 W 50 W 50 W

MAX 60 W 100 W 100 W

Sensitivity *1 (1 W, 1 m) 88 dB SPL 89 dB SPL 91 dB SPL

Maximum SPL *2 (Calculated, 1 m,

Peak) 106 dB SPL 109 dB SPL 111 dB SPL

Transformer Taps 100 V 1.5/3/6 W 3/6/12 W 3/6/12 W

70 V 0.8/1.5/3/6 W 1.5/3/6/12 W 1.5/3/6/12 W

Overload Protection Full-range power limiting to protect network and transducers

Connector Euroblock (4 pin) ×1

Wire size : Min. AWG24 (0.2 sq), Max. AWG16 (1.25 sq)

Baffle PP, black

Grille Metal Grille Punching metal, Powder coating

black (Munsell N3) / white (Munsell N9.3)

Trim Ring ABS, black (Munsell N3) / white (N9.3)

Back Can Steel, black

Dimensions (Including grille) Ø225 × D95 mm Ø286 × D106 mm Ø325 × D122 mm

Weight (Including grille) 2.1 kg 3.3 kg 4.2 kg

Cutout size Ø186 mm Ø247 mm Ø285 mm

Required ceiling board thickness 2 mm - 37 mm

Conduit tube Ø15.4 mm - Ø21.3 mm

Packaging 1 pc

Included in the

package

Grille, Safety wire, Cutout template, Owner's Manual

Reinforcing

Bracket Kit – C-Ring, Tile Rails × 2 C-Ring, Tile Rails × 2

Optional accessories AB-C2 – –

Wiring and installation shall be in accordance with the National Electrical Code, NFPA70 for United States, Canadian Electrical Code, CSA C22.1 for

Canada and the local authority having jurisdiction.

Installing the Speaker

Before installing the speaker onto the ceiling, ensure that the strength of the

ceiling rail is sufficient.

Pre-installation (Preparation of the Cable)

• For cables attached to the Euroblock plug, strip the insulation as shown

in the figure and connect them.

Put the supplied cutout template to the ceiling and draw a circle by tracing it.

Make sure to use the cutout template so that hole is the correct diameter.

If you use a circular cutter, set the diameter using the cutout template.

2. Cut the hole by tracing the circle.

Pull the wiring from the power amplifier through the cut hole of the ceiling.

2. Remove the terminal cover by loosening the four screws and pass the

cable through the removed terminal cover according to the wiring

direction.

In this manual, the example illustrations show the top terminal cover hole.

The terminal cover do not have a hole

through which the speaker cable passes.

Open a hole in the terminal cover (as shown)

to use.

3. Remove the Euroblock plug from the speaker. After loosening the

terminal screws of the Euroblock plug with a flat-blade screwdriver,

insert the cable into each terminal and tighten the screws.

Make sure that cables cannot be pulled out.

4. Plug the connected Euroblock plug into the socket in the speaker.

5. Tighten the screws and then attach the terminal cover.

NOTE

The example illustrations in this manual are of the VC4B.

CAUTION

Be careful not to hurt your hands when handling this product.

NOTICE

When installing the speakers, turn off the power amplifier.

NOTE

Do not plate core wires by soldering if the cable uses stranded wire.

Doing so will cause the wire to break.

Cut Out a Hole in the Ceiling

CAUTION

Wear goggles to prevent chips or powder entering your eyes

while cutting the hole.

When the included Reinforcing Bracket Kit or AB-C2 (sold

separately) is used

For the VC8B, VC8W, VC6B, and VC6W, the included Reinforcing

Bracket Kit must be used.

For the VC4B and VC4W, follow the instructions when using the AB-C2.

1. Insert the two tile rails through the cut hole and place them on the

ceiling surface within your reach. Adjust their length and be sure that

each of the tile rails are oriented as shown below.

2. Use the opening in the C-ring to slide one section of the C-Ring into

the cut hole, continuing to slide it around until the C-ring is

completely inside the ceiling.

3. Secure the C-ring and tile rails with the supplied two screws through

either slot of both C-ring brackets.

About 7 mm

Compatible cable:

Min. AWG24 (0.2 sq)

Max. AWG16 (1.25 sq)

C-ring

Tile rail

Connect the Wiring to the Connector

CAUTION

Use an appropriate tool for open-

ing the hole. Otherwise, injury

may result if you attempt to open

the hole with your bare hands.

Terminal cover

Speaker cable

Terminal screw

Loosen

Flat-blade

screwdriver

Euroblock plug

Tighten

Less than 3 mm

From amplifier

or previous

speakers

To subsequent

speakers Use a flat-blade

screwdriver with a blade

less than 3 mm.

1. Attach the safety wire to the safety wire ring, and connect the wire to an

independent support point, such as a joist.

2. Push the speaker slowly up into the ceiling, taking care not to trap the

speaker cable, carrying band or safety wire.

3. While lifting up the speaker, turn the screwdriver clockwise to tighten the

attachment screw.

The first turn of the attachment screw opens the clamp. Further turns

move the clamp down the channel to pull the speaker up into the ceiling.

When the clamp is difficult to open, turning the screwdriver halfway

counterclockwise once will make it easier to open the clamp.

Select the line voltage/impedance (100 V, 70 V, 16 Ω) and power tap for a

100 V, 70 V line distributed system, by rotating the tap selector switch on

the front side of the speaker with a flat-blade screwdriver.

When using the speaker with high-impedance connection, select the

position where wattage is indicated by the line (100 V, 70 V). Do not select

the “ × ” setting when connecting to a 100 V line.

When using it with low impedance connection, select the 16 Ω position.

Fix the Speaker onto the Ceiling

CAUTION

Always take measures to prevent the speaker from falling

down.

If the safety wire is too short, prepare another wire appropri-

ate for the speaker weight and installation conditions.

NOTICE

Do not over-tighten the attachment screws. Otherwise, the attachment

screws and clamps will break.

Safety wire ring

Safety wire

Carrying band

Safety wire Speaker

cable

Carrying band

Safety wire Speaker

cable

(VC4B, VC4W, VC6B,

VC6W, VC8B, VC8W)

When the included Reinforcing

Bracket Kit or AB-C2 (sold

separately; VC4B and VC4W

only) is used.

(VC4B, VC4W)

When the AB-C2 Reinforcing

Bracket Kit (sold separately)

is not used.

Attachment

screw

Clamp

Removing from the Ceiling

1. While pressing the speaker against the ceiling, loosen the

attachment screws by turning them counterclockwise.

Loosen the screw and the clamp goes up, and as it reaches the top,

the clamp closes as shown in figure below.

2. Remove the safety wire from the speaker that is detached from the

ceiling.

Set the Line Voltage/Impedance and Power

NOTICE

• Make sure the amplifier is switched off before operating the tap selector

switch.

• If the setting is incorrect, it may cause malfunction of the speaker and

amplifier.

Attach the Grille

CAUTION

• If the grille is not sufficiently turned, it may fall off. Sufficiently

turn the grille, until the fastening sections of the grille and

speaker are securely engaged.

• If the ceiling material is soft, the baffle surface may sink into

the ceiling material due to overtightening of the attachment

screws, and the grill may not fit properly.

Clamp

The illustration indicates the setting at 6 W for a

100 V line and 3 W for a 70 V line.

100V

1.5

70V

0.8

1.5

1 Align the grille with the cabinet’s

face and fit them together.

2 Turn clockwise (approx. 30°) to

secure the grille.

SPEAKER SYSTEM

VC8B VC8W VC6B VC6W VC4B VC4W

Owner’s Manual

English

VEY4150

NOTICE

To avoid the possibility of malfunction/damage to

the product or damage to other property, follow

the notices below.



 Handling and maintenance

• Do not expose the product to excessive dust or

vibration, or extreme cold or heat, in order to

prevent the possibility of panel disfiguration,

unstable operation, or damage to the internal

components.

• Be sure to observe the amplifier’s rated load

impedance, particularly when connecting

speakers in parallel at low impedance.

Connecting an impedance load outside the

amplifier's rated range can damage the

amplifier.

• When using a high-impedance speaker

connection, make sure the audio signal is

passed through an 60 Hz or above high-pass

filter before being input to the speakers.

• Do not touch the speaker driver unit, since it

might cause malfunction.

• Do not place vinyl, plastic or rubber objects on

the product, since this might cause alteration

or discoloration of the panel.

• When cleaning the product, use a dry and soft

cloth. Do not use paint thinners, solvents,

cleaning fluids, or chemical-impregnated

wiping cloths, since this might cause alteration

or discoloration.

• Protection Circuit

This speaker system has an internal protection

circuit that shuts off the speaker unit when an

excessive input signal is applied. If the

speaker unit emits no sound, reduce the

volume level of the amplifier immediately. (The

sound will return automatically in several

seconds.)

• Do not place the speaker face down with the

grille attached, as deformation of the grille may

result.

• When placing the baffle face down, always

place it on a flat surface.

Information



 About this manual

• The illustrations as shown in this manual are for

instructional purposes only.

• The company names and product names in

this manual are the trademarks or registered

trademarks of their respective companies.



 About disposal

• This product contains recyclable components.

When disposing of this product, please

contact the appropriate local authorities.

Yamaha cannot be held responsible for

damage caused by improper use or

modifications to the product.

Manual Development Group

Published 01/2022

CROD-A0

Yamaha Pro Audio global website

https://www.yamahaproaudio.com/

Yamaha Downloads

https://download.yamaha.com/

ADDRESS LIST

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan

Importer (European Union): Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

Importer (United Kingdom): Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, United Kingdom

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Toronto, Ontario,

M1S 3R1, Canada

Tel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620,

U.S.A.

Tel: +1-714-522-9011

MEXICO

Yamaha de México, S.A. de C.V.

Av. Insurgentes Sur 1647 Piso 9, Col. San José

Insurgentes, Delegación Benito Juárez, CDMX,

C.P. 03900, México

Tel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Praça Professor José Lannes, 40, Cjs 21 e 22, Brooklin

Paulista Novo CEP 04571-100 – São Paulo – SP, Brazil

Tel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,

Sucursal Argentina

Olga Cossettini 1553, Piso 4 Norte,

Madero Este-C1107CEK,

Buenos Aires, Argentina

Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN

AMERICAN/CARIBBEAN REGIONS

Yamaha Music Latin America, S.A.

Edif. Torre Banco General, Piso 7, Urbanización

Marbella, Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, República de Panamá

Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, U.K.

Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch Switzerland

in Thalwil

Seestrasse 18a, 8800 Thalwil, Switzerland

Tel: +41-44-3878080

AUSTRIA/BULGARIA/

CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH

Branch Austria

Schleiergasse 20, 1100 Wien, Austria

Tel: +43-1-60203900

POLAND

Yamaha Music Europe GmbH

Sp.z o.o. Oddział w Polsce

ul. Wielicka 52, 02-657 Warszawa, Poland

Tel: +48-22-880-08-88

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta

Tel: +356-2133-2093

NETHERLANDS/BELGIUM/

LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5b, 4133 AB Vianen, The Netherlands

Tel: +31-347-358040

FRANCE

Yamaha Music Europe

7 rue Ambroise Croizat, Zone d'activités de Pariest,

77183 Croissy-Beaubourg, France

Tel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Via Tinelli N.67/69 20855 Gerno di Lesmo (MB), Italy

Tel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal en

España

Ctra. de la Coruña km. 17,200, 28231

Las Rozas de Madrid, Spain

Tel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House

19th klm. Leof. Lavriou 190 02 Peania – Attiki,

Greece

Tel: +30-210-6686168

SWEDEN/FINLAND/ICELAND

Yamaha Music Europe GmbH Germany filial

Scandinavia

JA Wettergrensgata 1, 400 43 Göteborg, Sweden

Tel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark,

Fillial of Yamaha Music Europe GmbH, Tyskland

Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark

Tel: +45-44-92-49-00

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, 1332 Østerås, Norway

Tel: +47-6716-7800

CYPRUS

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-303-0

RUSSIA

Yamaha Music (Russia) LLC.

Room 37, entrance 7, bld. 7, Kievskaya street, Moscow,

121059, Russia

Tel: +7-495-626-5005

OTHER EUROPEAN REGIONS

Yamaha Music Europe GmbH

Siemensstrasse 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Türkiye İ Şstanbul ubesi

Mor Sumbul Sokak Varyap Meridian Business 1.Blok

No:1 113-114-115

Bati Atasehir Istanbul, Turkey

Tel: +90-216-275-7960

OTHER REGIONS

Yamaha Music Gulf FZE

JAFZA-16, Office 512, P.O.Box 17328,

Jebel Ali FZE, Dubai, UAE

Tel: +971-4-801-1500

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: +86-400-051-7700

INDIA

Yamaha Music India Private Limited

P-401, JMD Megapolis, Sector-48, Sohna Road,

Gurugram-122018, Haryana, India

Tel: +91-124-485-3300

INDONESIA

PT Yamaha Musik Indonesia Distributor

Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto

Kav. 4, Jakarta 12930, Indonesia

Tel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.

11F, Prudential Tower, 298, Gangnam-daero,

Gangnam-gu, Seoul, 06253, Korea

Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.

No.8, Jalan Perbandaran, Kelana Jaya, 47301

Petaling Jaya, Selangor, Malaysia

Tel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited

Block 202 Hougang Street 21, #02-00,

Singapore 530202, Singapore

Tel: +65-6740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co.,Ltd.

2F., No.1, Yuandong Rd., Banqiao Dist.,

New Taipei City 22063, Taiwan (R.O.C.)

Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd.

3, 4, 15, 16th Fl., Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited

15th Floor, Nam A Bank Tower, 201-203 Cach Mang

Thang Tam St., Ward 4, Dist.3,

Ho Chi Minh City, Vietnam

Tel: +84-8-3818-1122

OTHER ASIAN REGIONS

http://asia.yamaha.com/

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 80 Market Street, South Melbourne,

VIC 3205, Australia

Tel: +61-3-9693-5111

REGIONS AND TRUST TERRITORIES

IN PACIFIC OCEAN

http://asia.yamaha.com/

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

PA57

Dimensions

Unit: mm

VC8B VC8W VC6B VC6W VC4B VC4W

AB-C2

C-Ring

VC4B VC4W

Reinforcing Bracket Kit

VC8B VC8W VC6B VC6W

Ø285

Ø335

608

644

31.8

608

644

31.8

Ø247

Ø297

C-Ring C-Ring

Tile Rail Tile Rail

Ø186

Ø243 30

Tile Rail

608

644

Ø325

Ø286

Ø225

Ø279

Ø241

107

Ø180

122

106

Product specificaties

Merk:	Yamaha
Categorie:	Speaker
Model:	VC4B
Kleur van het product:	Zwart
Gewicht:	2100 g
Bluetooth:	Nee
Connectiviteitstechnologie:	Bedraad
Diameter:	225 mm
Gemiddeld vermogen:	- W
Aantal per verpakking:	1 stuk(s)
Aanbevolen gebruik:	Universeel
Impedantie:	16 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Plafond-montage
Woofer:	Ja
Luidspreker soort:	2-weg
Versterker:	Ingebouwd
Diameter woofer:	0.8 "
Diameter hogetonenluidspreker:	4 "
Tweeter:	Ja