Xaoc Katowice Handleiding
Xaoc
Niet gecategoriseerd
Katowice
Bekijk gratis de handleiding van Xaoc Katowice (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 20 mensen en kreeg gemiddeld 4.8 sterren uit 10.5 reviews. Heb je een vraag over Xaoc Katowice of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
stereo
variable band
isolator
Model of 1978
operator’s manual rev. 1978/1.0
Thank you for purchasing this Xaoc Devices
product. Katowice is a stereo variable–band
isolator that allows the user to manipulate
module in a series of upcoming Xaoc Devices
stereo signals.
Katowice splits the stereo input signal into
three bands: low, middle, and high. While
frequency and bandwidth of the mid band,
the low and high bands are automatical-
ly adjusted so that the sum of all three is a
complete signal. All three bands are passed
through high quality VCAs and their stereo
outputs are available separately for further
available.
Katowice may be used as a crossover net-
other band-selective applications, including
multiband compression and stereo enhance-
ment.
The module requires 10hp worth of free
space in the Eurorack cabinet. The rib-
bon-type power cable must be plugged into
the bus board, paying close attention to po-
larity orientation. The red stripe indicates
the –12V rail and should point in the same
direction on both the bus board and the unit.
The module itself is secured against reversed
power connection, however, reversing the
16-pin header may cause serious damage
to other components of your system because
it will short-circuit the +12V and +5V power
rails.
The module should be fastened by mounting
the supplied screws before powering up. To
better understand the device, we strongly
advise the user to read through the entire
manual before using the module.
The stereo pair of signal inputs is
AC-coupled and accepts all Eurorack signal
levels (up to 20Vpp), however, a conservative
-
ing certain signals may occasionally result
in increased amplitude and cause distortion.
the position of the two knobs: mid freq
sets the geometric center of the middle band
(in Hz), and mid width sets the width of
this band (in octaves). The corresponding
two jacks and allow for voltage control
and accept voltages in ±5V range. The ampli-
tude of the middle band is controlled by the
central mid slider and the corresponding
CV input above that accepts voltages in
the range of ±8V. The left slider low and
CV input control the amplitude of low fre-
module
explained
front panel
overview
fig. 1: interface
Product specificaties
| Merk: | Xaoc |
| Categorie: | Niet gecategoriseerd |
| Model: | Katowice |
Heb je hulp nodig?
Als je hulp nodig hebt met Xaoc Katowice stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Xaoc
7 Januari 2025
31 Augustus 2024
3 Augustus 2023
3 Augustus 2023
3 Augustus 2023
3 Augustus 2023
3 Augustus 2023
3 Augustus 2023
3 Augustus 2023
3 Augustus 2023
Handleiding Niet gecategoriseerd
- Honor
- Scala
- CDVI
- Gitzo
- Total
- Key Digital
- Amica
- Anslut
- Supermicro
- After Later Audio
- Dracast
- SMAJAYU
- Manhattan
- Aquatica
- BaByliss
Nieuwste handleidingen voor Niet gecategoriseerd
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025