Winegard HD7698 Handleiding
Winegard
Niet gecategoriseerd
HD7698
Bekijk gratis de handleiding van Winegard HD7698 (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.7 sterren uit 2 reviews. Heb je een vraag over Winegard HD7698 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
1450292
Rev7 3-21
VHF/UHF MODELS
HD7698 HD8200&
High Definition VHF/UHF Antennas
INSTRUCTION MANUAL
Register your product at winegard.com/myantenna
For help, email help@winegard.com
HD7698
HD8200
WARNING
:
Installation of the antennas near power lines is dangerous!
For your safety, follow the installation instructions.
POINT THIS END
TOWARD STATIONS
POINT THIS END
TOWARD STATIONS
NOTE: Unfolding elements procedure is the same for both
HD7698 & HD8200 antennas.
PARTS LIST
ASSEMBLY
STEP 1 - Contents of Package
A. Remove all parts from the box and compare to parts list
to ensure nothing is missing and to become familiar with
the part names. See figure1.
STEP 2 - Front Section
A. Stand front section up vertically and unfold all elements
(in any order) until they snap into place.
B. Remove bolt, hex nut, and director element from the
front section boom. See figure 2.
C. Unfold the UHF directors. See figure 2.
D. Set front section aside being careful not to bend
the elements (laying it flat on the ground is the
best position).
Front Assembly
Rear Assembly
Mast Clamp
Mast Clamp
Boom Brace
Corner Reflector Assembly (2)
Flat Head Screwdriver
Phillips Screwdriver
Crescent Wrench or Pliers
Cartridge
Housing
Boot
TOOLS REQUIRED
(not included)
FIGURE 1
FIGURE 2 - Front Assembly
FIGURE 3 - Rear Assembly
UHF Director,
(Unfolded)
UHF Directors
UHF Directors
Director Element
Cartridge Housing
8 Up
6 Up
4 Up, Over
& Down
2 Up, Over
& Down
7 Down, Over & Up
5 Down
3 Down
1 Down
STEP 3 - Rear Section
A. Stand rear section up vertically with cartridge housing up
and facing away from you.
B. Alternately unfold elements per figure 3 in direction
of arrows until they lock into place in the black plastic
blocks.
C. Spin the rear section around so the cartridge housing is
now facing you. Unfold the remaining elements in the
same order. See figure 3 for completely unfolded rear
section.
WARNING: Be sure the phasing lines DO NOT touch the
metal bracket or the antenna boom. See FIGURE 4.
NOTE: The HD8200 antenna tuning stubs do not need
to touch the boom.
STEP 4 - Attaching Front Section to Rear Section
A. Slide the front boom into the rear boom making sure to
feed the UHF phasing lines into the holes near the top
of the cartridge housing, and into the slotted pegs inside
the housing. See figure 4. When finished, the phasing
lines will be resting in the slots of the pegs, but will not
extend out the back side of the cartridge housing.
B. Reinstall the director element, bolt and nut. See
figure 2.
STEP 5 - Cartridge Housing
A. Attach the cartridge housing cover so all 4 snaps are
locked in place. Direction of the housing does not matter.
See figure 5.
STEP 6 - Corner Reflector Assemblies
A. Unfold the elements on the corner reflector booms.
Element clip tips should point away from the open end of
each boom. See figure 6.
B. Attach the corner reflector booms using the supplied
nuts and bolts. See figure 6.
STEP 7 - Boom Brace
A. Install the boom brace by first removing the bolts and
hex nuts.
B. With the cartridge housing facing down, install the boom
brace to the top corner reflector boom first, making sure
the mast clamps are on the same side. See figure 7.
Only finger tighten the bolt and hex nut.
C. Swing the other end of the boom brace down onto the
rear section and insert the bolt and hex nut.
D. Tighten both bolts and nuts (on each end of the boom
brace) securely.
FIGURE 4 - Front Section to Rear Section
FIGURE 5 - Attach Cartridge Housing
FIGURE 6 - Corner Reflector Assemblies
FIGURE 7 - Boom Brace Installed
Cartridge Housing
UHF Phasing Lines
Cartridge Housing
V-shaped
tuning stub
Element Clip Tips
Pointing away from
open end of boom
Attach the corner
reflector booms
Install this
end first
Install this
end last
Mast
Clamps
Cartridge Housing,
(Facing Down)
Be sure the phasing
lines DO NOT touch
the metal bracket or
the antenna boom.
Product specificaties
| Merk: | Winegard |
| Categorie: | Niet gecategoriseerd |
| Model: | HD7698 |
Heb je hulp nodig?
Als je hulp nodig hebt met Winegard HD7698 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Winegard
8 April 2025
15 November 2023
15 November 2023
Handleiding Niet gecategoriseerd
- Noma
- Linear
- WHALE
- Powertec
- Sonuus
- Pro-Ject
- Mooer
- Unger
- ETON
- Premier
- Zhiyun
- DEXP
- Vaillant
- APDTY
- Now TV
Nieuwste handleidingen voor Niet gecategoriseerd
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025