Whirlpool TDLR 7222BS NX/N Handleiding

Whirlpool Wasmachine TDLR 7222BS NX/N

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool TDLR 7222BS NX/N (4 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

1 Programme selector

2 “Start/Pause“ button

3 “Reset/Drain“ button

4 “Temperature“ button

5 “Start delay“ button

6 Child lock combination

7 “Spin“ button

8 Time

9 Temperature

10 Washing phase

INDICATORS

Detergent over dosage

Door open

Failure: Service

Failure: Clean pump

Failure: Water tap closed

In the event of any failure, refer to the

“TROUBLESHOOTING“ section

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.whirlpool.eu/register

CONTROL PANEL

PROGRAMME CHART

PRODUCT DESCRIPTION

1. Lid handle

2. Lid

3. Control panel

4. Detergent dispenser

5. Drum

6. Water lter - behind the cover

7. Mobility lever (depending on model)

8. Adjustable feet (x2)

DETERGENT DISPENSER

Main wash compartment

Detergent for the main wash, stain remover or

water softener.

Prewash compartment

Detergent for the prewash.

Softener compartment

Fabric softener. Liquid starch. Bleach.

Pour in softener, starch or bleach solution only

up to the “max” mark.

Release button 

Press to remove tray for cleaning.



Quick guide

Before using the appliance carefully read the Safety Instruction.

Before using the machine, it is imperative that the transport bracket is removed.

For more detailed instructions on how to remove it, see the Installation Guide.

1 2 3 4 5 6

10 89

Max load 7,0 Kg

Power consumption in o-mode 0,11 W / in left-on mode 0,11 W Detergents and additives Recommended

detergent

Residual

dampness % *

Energy

consumption

kWh

Total water lt

Laundry

temperature °C

Programme

Temperatures Max.

Spin

speed

(rpm)

Max

load

(kg)

Dura-

tion (h

: m)

Prewash Main

wash Softener

Powder Liquid

Setting Range

Rapid 30’ 30°C 20 - 30°C 1200 3,0 0:30    – 57 0,25 42 27

40°C 40°C

1151 7,0 3:25 –     53 1,23 59 43

1151 3,5 2:40 –     53 0,58 40 40

1151 2,0 2:00 –     53 0,34 30 31

Aqua saver 40°C 20 - 40°C 1200 2,5 ** –  – –  – – – –

Colours 40°C 20 - 60°C 1000 4,0 **     – – – –

Jeans 40°C 20 - 60°C 1000 4,0 **    – – – – –

Hygiene 60°C 60°C 1200 7,0 ** –     – – – –

20°C 20°C 1200 7,0 3:15 –   – 53 0,25 48 20

Rinse & Spin – – 1200 7,0 ** – –  – – – – – –

Spin – – 1200 7,0 ** – – – – – – – – –

Wool 40°C 20 - 40°C 1000 1,0 ** –   – – – – –

Delicates 40°C 20 - 40°C 1000 1,5 **    – – – – –

Synthetics 40°C 20 - 60°C 1200 3,0 2:15      40 0,56 50 40

Cotton 60°C 20 - 95°C 1200 7,0 2:35      55 1,10 54 55

Mixed 40°C 20 - 60°C 1200 3,0 ** –     – – – –

Eco cotton 60°C 60°C 1200 7,0 4:00 –     53 0,85 48 --

3,5 3:00 –     53 0,58 34 --

40°C 1200 3,5 3:00 –     53 0,56 34 --

  Dosing required Dosing optional

This data may dier in your home due to changing conditions in inlet water temperature,

water pressure etc. Approximate programme duration values refer to the default setting of

the programmes, without options. The values given for programmes other than the eco 40-

60 programme are indicative only.

* After programme end and spinning with maximum selectable spin speed, in default

programme setting.

** The duration of the programme is shown on the display.

6th Sense - The sensor technology adapts water, energy and programme duration to your

wash load.

Eco cotton - Test wash cycles in compliance with regulations 1061/2010. Set wash cycle at

a temperature of 40°C or 60°C to access this cycles.

Eco 40-60 - Test wash cycle in compliance with 2019/2014 regulation. The most ecient

programme in terms of energy and water consumption for washing normally soiled cotton

laundry. Display only: Spin speed values shown on the display can slightly diers from the

values stated in the table

For all Test Institutes

Long wash cycle for cottons: set wash cycle Cotton with a temperature of 40°C.

Synthetic program along: set wash cycle Synthetics with a temperature of 40°C.

PROGRAMMES

For choosing the appropriate programme for your kind of

laundry, always respect the instructions on the care labels of

the laundry. The value given in the tub symbol is the maximum

temperature possible for washing the garment.

Rapid 30’

For washing lightly soiled garments quickly. This cycle lasts only 30 minutes,

saving time and energy.

Eco 40-60

For washing normally soiled cotton garments declared to be washable at 40

°C or 60 °C, together in the same cycle. This is the standard cotton programme

and the most efficient in terms of water and energy consumption.

Aqua saver

Lightly soiled laundry made of synthetic fifibres, or synthetics mixed with

cotton garments. Saving programme with a very low water consumption. Use

liquid detergent and the lowest recommended amount for 2.5kg laundry. Do

not use softener.

Colours

White and pastel shaded garments made of delicate fabrics.

Gentle wash programme to avoid graying or yellowing of your laundry. Use

heavy duty detergent, if necessary also stain removers or bleaches on oxygen

basis. Do not use liquid detergent.

Jeans

Turn garments inside-out before washing and use a liquid detergent.

Hygiene

This program removes 99 % of bacteria while washing normally to heavily

soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton

and linen.

20 °C

For washing lightly soiled cotton garments, at a temperature of 20 °C.

Rinse & Spin

Separate rinse and intensive spin programme. For robust

laundry.

Spin

Spins the load then empties the water. For robust laundry.

Wool

All wool garments can be washed using programme ‚ “Wool“ even those

carrying the “hand-wash only“ label. For best results, use special detergents

and do not exceed max kg declaration of laundry.

Delicates

For washing particularly delicate garments. Preferably turn garments inside

out before washing.

Synthetics

For washing soiled garments made from synthetic fibres (such as polyester,

polyacrylic, viscose, etc.) or cotton/synthetic blends.

Cotton

Normally to heavily soiled and robust cottons .

Mixed

For washing lightly to normally soiled resilient garments in cotton, linen,

synthetic fibres and mixed fibres.

Eco cotton

For washing normally soiled cotton garments. At 40°C and 60°C

FIRST TIME USE

To remove any manufacturing debris select the “Cotton“ programme at

a temperature of 95°C. Pour a small quantity of detergent powder into the

main wash compartment of the detergent dispenser (maximum 1/3 of the

quantity the detergent manufacturer recommends for lightly soiled laundry).

Start the programme without adding any laundry.

DAILY USE

Prepare your laundry according to the recommendations in the “HINTS

AND TIPS“ section. Load the laundry, close the drum door and check that

it is closed properly. Pour in the detergent and any additives. Observe the

dosing recommendations on the detergent pack. Close the lid. Turn the

programme selector to the desired programme and select any option if

needed. The display shows the duration of the selected programme (in hours

and minutes), and the indicator for the “Start/Pause“ button flashes. The

temperature and spin speed can be changed by pressing the “Temperature“

button or the “Spin“ button. Open the tap and press the “Start/Pause“

button to start the wash cycle. The “Start/Pause“ indicator will lights up

and the door will be locked. Due to variations in load and temperature of inlet

water, the remaining time is newly calculated in certain programme phases. If

this is the case, an

animation appears on the time display.

PAUSE OR CHANGE A RUNNING PROGRAMME

To pause the wash cycle, press the “Start/Pause“ , the indicator light button

blinks. Select any new programme, temperature, options or spin speed if you

wish to change those settings. Press the “Start/Pause“ button again to

start the wash cycle from the point at which it was interrupted. Do not add

detergent for this programme.

DOOR OPEN INDICATOR

Before starting and after the end of a programme, the “Door open“

indicator lights to show that the lid can be opened. As long as a wash

programme is running, the lid remains locked and must on no account be

forced open. In case you have an urgent need to open it during a running

programme, for example to add more laundry, or to remove laundry

which was loaded by mistake, press the “Start/Pause“ button. If the

temperature is not too high, the “Door open“ indicator light turns on.

It may last a while until you can open the lid. Press “Start/Pause“ to

proceed with the programme again.

PROGRAMME END

The “Door open“ indicator lights up and the display shows . Turn the

programme selector to the “O“ position and close the water tap. Open the

lid and drum and unload the machine. Leave the Lid open for some time to

allow the interior of the machine to dry. After about a quarter of an hour,

the washing machine will switch off completely to save energy.

To cancel a running programme before the end of cycle, press the

“Reset/Drain“ button for at least 3 seconds. The water is drained out. It

may last a while until you can open the lid.

OPTIONS

! When the combination of programme and additional option(s) is not

possible, the indication lights switch o automatically.

! Unsuitable combinations of options are deselected automatically.

Colours 15°

Saves energy used for water heating while maintaining a good wash

result. Supports colour maintenance when washing coloured laundry.

Recommendable for lightly soiled laundry without stains. Make sure that your

detergent is suitable for cold wash temperatures.

FreshCare

Select this option if you cannot unload the laundry soon after programme

end, or if you tend to forget the laundry in your washing machine. It will

help to keep your laundry fresh. The washing machine will start to tumble

the laundry periodically after programme end. The light of the “Fresh care“

button will blink while this function is active, and the display will show an

animation. The periodic tumbling will last up to approximately 6 hours after

the end of your wash programme, and you can stop it at any time by pressing

the “Fresh care“ button. It will last a while until you can open the door. After

the “Fresh care“ period has run out, the display indicates .

Temperature

Every programme has a predefined temperature. If you want to change the

temperature, press the “Temperature“ button. The value appears on the

display.

Start delay

To set the selected programme to start at a later time, press the “Start delay“

button to set the desired delay time. The lamp for the

“Start delay“ option button lights up, and it goes off when the programme

starts. Once having pressed the “Start/Pause“ button, the countdown

of the time delay begins. Number of hours pre-selected can be reduced by

pressing the “Start delay“ button again. Do not use liquid detergent

when activating this option. To cancel the “Start delay“ turn the

programme selector to another position.

Rapid

Enables quicker washing by shortening the programme duration.

Recommendable for small loads or only lightly soiled laundry.

Prewash

Only for heavily soiled loads (for example sand, granular dirt). Increases the

cycle time by approximately 15 min. Do not use liquid detergent for the main

wash when activating the Prewash option.

Intensive rinse

Helps to avoid detergent residues in the laundry by extending the rinse

phase. Particularly suitable for washing baby laundry, for people suffering

from allergies and for areas with soft water.

Spin

Every programme has a predefined spin speed. If you want to change the

spin speed, press the “Spin“ button. If spin speed “0“ is selected, the final

spinning is cancelled but intermediate spin peaks remain during the rinse.

The water is drained out only.

CHILD LOCK

You can lock the buttons of the control panel against improper use (e.g. by

children). Press both of the child lock buttons simultaneously and hold them

for at least 3 seconds. The key symbol on the display lights up. To

unlock the buttons again proceed in the same way.

BLEACHING

Wash your laundry in the desired programme, Cotton or Synthetics ,

adding an appropriate amount of chlorine bleach to the Softener chamber

(close the lid carefully). Immediately after the end of the programme, turn the

“Programme selector” and start the desired programme again to eliminate

any residual bleach smell; if you want, you can add softener. Never put both

chlorine bleach and softener into the softener chamber at the same time.

HINTS AND TIPS

Sort your laundry according to

Type of fabric/care label (cotton, mixed fifibres, synthetics, wool, handwash

items). Colour (separate coloured and white items, wash new coloured items

separately). Delicates (wash small items – like nylon stockings – and items

with hooks – like bras – in a cloth bag or pillow case with zip).

Empty all pockets

Objects like coins or lighters can damage your laundry as well as the drum.

Appliance interior

If you never or seldom wash your laundry at 95°C, we recommend to

occasionally run a 95°C programme without laundry, adding a small amount

of detergent, to keep the interior of the appliance clean.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus

detergent in your laundry and it saves money by avoiding waste of surplus

detergent

Use low temperature and longer duration

The most efficient programmes in terms of energy consumption are generally

those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the “PROGRAMME

CHART” table to save water and energy.

Noise and remaining moisture content

They are influenced by the spinning speed: the higher the spinning speed

in the spinning phase, the higher the noise and the lower the remaining

moisture content.

CLEANING & MAINTENANCE

For any cleaning and maintenance, switch off and unplug the washing

machine. Do not use flammable fluids to clean the washing machine. Clean

and maintain your washing machine periodically (at least 4 times per year).

Cleaning the outside of the washing machine

Use a soft damp cloth to clean the outer parts of the washing machine. Do

not use glass or general purpose cleaners, scouring powder or similar to clean

the control panel – these substances might damage the printing.

Detergent dispenser

Clean regularly, at least three or four times a year, to prevent detergent build-

up:

Press the release button to release the detergent dispenser and remove it. 

A small quantity of water can remain in the dispenser, thus you should carry it

in an upright position. Wash the dispenser using running water. You can also

remove the siphon cap on the back of the

dispenser for cleaning. Replace the siphon cap in the dispenser (if removed)

Reinstall the dispenser by locating the dispenser’s bottom tabs into the

appropriate openings on the lid, and by pushing the dispenser against the

lid until it locks into place. Make sure that the detergent dispenser is correctly

reinstalled.

Checking the water supply hose

Check the inlet hose regularly for brittleness and cracks. If damaged, replace

it by a new hose available through our After-Sales Service or your specialist

dealer. Depending on the hose type: If the inlet hose has a transparent

coating, periodically check if the colour intensifies locally. If yes, the hose

may have a leak and should be replaced. For water stop hoses (If

available): check the small safety valve inspection window (see arrow). If it is

red, the water stop function was triggered, and the hose must be replaced

by a new one. For unscrewing this hose, press the release button (if available)

while unscrewing the hose.

Cleaning the mesh filters in the water supply hose

Check and clean regularly (at least two or three times a year).

Close the tap and loosen the inlet hose on the tap. Clean the internal mesh

filter and screw the water inlet hose back onto the tap. Now unscrew the inlet

hose on the rear of the washing machine. Pull off the mesh filter from the

washing machine connection with universal pliers and clean it. Refit the mesh

filter and screw the inlet hose on again. Turn on the tap and ensure that the

connections are completely water-tight.

Cleaning the water filter / draining residual water

The washing machine is provided with a self-cleaning pump. The filter keeps

objects like buttons, coins, safetypins etc. which have been left in the laundry.

If you used a hot wash programme, wait until the water has cooled down

before draining any water. Clean the water filter regularly, to avoid that the

water cannot drain after the wash due to obstruction of the filter. If the water

cannot drain, the indicator indicates that the water filter may be clogged.

Open the filter cover with a coin. Place a broad, flat container beneath the

water filter, to collect the drain water. Slowly turn the filter counterclockwise

until water flows out. Let the water flow out, without removing the filter.

When the container is full, close the water filter by turning it in clockwise.

Empty the container. Repeat this procedure until all the water has drained. Lay

a cotton cloth beneath the water filter, which can absorb a small amount of

rest water. Then remove the water filter by turning it out anti clockwise. Clean

the water filter (remove residues in the filter and clean it under running water)

and the filter chamber. Make sure the pump impeller (in the housing behind

the filter) is not obstructed. Insert the water filter and close the filter cover:

Reinsert the water filter again by turning it in clockwise direction. Make sure

to turn it in as far as it goes. To test water tightness of the water filter, you can

pour about 1 liter of water into the drum and check that water does not leak

from the filter. Then close the filter cover.

Lid seal

Check the condition of the lid seal periodically and clean it from time to time

with a damp cloth.

Recovering an object that falls between the drum and the tub

If an object accidentally falls between the drum and the tub, you can recover

it thanks to one of the removable drum lifters.

Unplug the washing machine. Remove the laundry from the drum. Close the

drum flaps and turn the drum a half-turn (picture ). Using a screw-driver a

press on the plastic end, while sliding the lifter from left to right (picture b, c)

by hand it will fall into the drum. Open the drum. You can recover the object

through the hole in the drum. Refit the lifter from inside the drum: Position

the plastic tip above the hole on the right side of the drum (picture d). Then

slide the plastic lifter from right to left until it clips. Close the drum flaps again,

turn the drum through half a turn and check the positioning of the blade at all

its anchorage points. Plug the washing machine in again.

TRANSPORT AND HANDLING

Pull out the mains plug, and close the water tap. Disconnect the inlet hose

from the water tap, and remove the drain hose from your draining point.

Remove all rest water from the hoses and washing machine and fix hoses

so that they cannot get damaged during transport. To facilitate moving the

machine, pull the mobility lever situated at the bottom front (if available on

your model) out a little by hand. Pull the washing machine out to the stop

with the foot. Afterwards push the mobility lever back into the original stable

position. Refit the transport bracket. Follow the instructions for removing the

transport bracket in the INSTALATION GUIDE in reverse order.

abcd

Quick guide

Product specificaties

Merk:	Whirlpool
Categorie:	Wasmachine
Model:	TDLR 7222BS NX/N
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Buttons,Rotary
Kleur van het product:	Wit
Deurscharnieren:	Boven
Ingebouwd display:	Ja
Gewicht:	56000 g
Breedte:	400 mm
Diepte:	600 mm
Hoogte:	900 mm
Netbelasting:	2000 W
Type stekker:	Type F (CEE 7/4)
Type lader:	Bovenbelading
Materiaal trommel:	Kunststof
Snoerlengte:	2 m
Trommelinhoud:	42 l
Resterende tijd indicatie:	Ja
Energie-efficiëntieklasse:	E
Energieverbruik wassen:	0.783 kWu
Waterconsumptie per cyclus:	45 l
Centrifuge-droger klasse:	B
Geluidsniveau (wassen):	- dB
Sopschuimbewaking:	Ja
Onbalanscontrolesysteem:	Ja
Aanpasbare centrifugesnelheid:	Ja
Maximale centrifugesnelheid:	1200 RPM
Stroom:	10 A
Geluidsemissieklasse:	A
Geluidsniveau bij centrifugeren:	72 dB
Restvochtpercentage:	53 procent
Cyclustijd (max):	225 min
Duur cyclus (snelwas programma):	30 min
Energieverbruik per 100 cycli:	78 kWu
AquaStop-functie:	Ja
Stroomverbruik (in standby):	0.11 W
Stroomverbruik (indien uit):	0.11 W
Nominale capaciteit:	7 kg
AC-ingangsspanning:	220 - 230 V
AC-ingangsfrequentie:	50 Hz
Energie-efficiëntieschaal:	A tot G
Maximale wastemperatuur:	43 °C
Wasprogramma's:	Eco,Wool,Quick,Sport,Rinse & spin,Delicate/silk