Whirlpool CGM2745FQ Handleiding

Whirlpool Wasdroger CGM2745FQ

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool CGM2745FQ (6 pagina's) in de categorie Wasdroger. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
Removing Greenwald Coin Slides from Coin Boxes
Tools Needed
5/16" socket wrench 5/16" open end wrench
1. Disconnect coin slide
harness and ground jumper
With the service door open, disconnect
the coin slide harness by pressing down
on the locking tab and pulling apart. Also
disconnect the ground jumper.
2. Loosen coin slide bolt
Using a 5/16" socket wrench or 5/16" open
end wrench, loosen the coin slide bolt. Set
the bolt aside.
or
W11032801B
3. Remove coin slide
Remove the coin slide by pushing up, then
pulling out (it may require some twisting and
turning).
6. Tighten coin slide bolt,
reattach harness and
ground jumper, and test
Align the long bolt, insert, and tighten using
a 5/16" socket wrench or 5/16" open end
wrench. Reattach the harness and ground
jumper and test.
4. Change vend price (see
page 2 of this instruction)
See page 2 of this instruction for information
on how to change the vend price.
5. Reinsert coin slide
Reinsert the coin slide in the coin box by
pushing the slide as far back as possible,
and then pushing down to lock it in place.
Locate the threaded bolt hole.
1
2
Changing the Vend Price on Greenwald Coin Slides
Tools Needed
Phillips screwdriver Quarters (up to 8) Coin slot plugs
(if needed; eight [8]
are provided)
1. Remove spring from coin slide
Remove the one large spring from the coin
slide assembly.
3. Separate coin slide
assembly into three sections
Remove the two screws holding the cover
and switch extension to the assembly (A).
With the screws removed, the assembly
breaks down into three components (and
the spring).
4. Remove two screws
holding plug retainer
With the slide fully forward, remove the
two screws holding the plug retainer.
2. Push slide fully forward
Fill the empty coin slots with quarters
and push the coin slide fully forward.
The quarters will drop free. Do not retract
the coin slide until instructed.
BA
Reassemble the cover and switch extension
to the coin slide. Secure with the screws
removed in Step 3. Note the location
of the bolt within the slider on the extension
(see illustration). This is important to the
function of the slide.
5. Turn over assembly and
adjust locations and number
of coin slot plugs
With the retainer removed, turn over the
assembly and adjust the locations and
number of coin slot plugs as needed.
Keep and store extra plugs, as they may
be needed in the future.
6. Replace plug retainer
Replace the plug retainer. Note that the word
“UP” is embossed on the visible side (see
illustration). Secure with the screws removed
in Step 4. It is helpful to hold this in place
with one hand while the screws are replaced
on the opposite side.
UP
R bl th d it h t i
7. Reassemble cover
and switch extension
8. Insert quarters
and test for function
Insert the appropriate number of quarters
in the coin slide and test for function. Make
sure the slider moves freely and engages
the switch.
9. Reattach spring
Reattach the single spring and insert the coin
slide assembly back into the meter case per
the instructions on page 1.
3
Retirer les glissières à monnaie Greenwald des boîtes à monnaie
Outillage nécessaire
Clé à douille de 5/16" (8 mm) Clé plate de 5/16" (8 mm)
ou
2. Desserrer le boulon
de la glissière à monnaie
À l’aide d’une clé à douille de 5/16" (8 mm)
ou d’une clé plate de 5/16" (8 mm), desserrer
le boulon de la glissière à monnaie. Mettre
le boulon de côté.
3. Retirer la glissière à monnaie
Retirer la glissière à monnaie en tirant vers
le haut, puis vers l’extérieur (il sera peut-être
nécessaire de tourner et secouer la glissière
à monnaie).
6. Serrer le boulon de la glissre
à monnaie, rebrancher le
faisceau et le cavalier de terre
et contrôler
Aligner le long boulon, l’insérer et le serrer en
utilisant une clé à douille de 5/16" (8 mm) ou
une clé plate de 5/16" (8 mm). Rebrancher le
faisceau et le cavalier de terre, puis contrôler
le fonctionnement.
4. Modi er le prix de vente
(voir page 4 de cette feuille
d’instructions)
Consulter page 4 de cette feuille
d’instructions pour savoir comment modi er
le prix de vente.
5. Replacer la glissière à monnaie
Replacer la glissière à monnaie dans la boîte
à monnaie en la poussant dans l’espace
aussi loin que possible, puis en appuyant
vers le bas pour la verrouiller en place.
Repérer le trou de boulon leté.
1. Débrancher le faisceau
de la glissière à monnaie
et le cavalier de terre
En gardant la porte de service ouverte,
débrancher le faisceau de la glissière à
monnaie en appuyant sur la languette de
verrouillage et en tirant sur les deux parties.
Aussi débrancher le cavalier de terre.


Product specificaties

Merk: Whirlpool
Categorie: Wasdroger
Model: CGM2745FQ

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool CGM2745FQ stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasdroger Whirlpool

Handleiding Wasdroger

Nieuwste handleidingen voor Wasdroger