Watson AM-192-B Handleiding
Watson
Accu's camera
AM-192-B
Lees hieronder de 📖 handleiding in het Nederlandse voor Watson AM-192-B (4 pagina's) in de categorie Accu's camera. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
Thank you for choosing Watson Pro
Please read this user manual carefully, and keep
it for reference before using the battery.
AM-192-B
VM-192-B
Buddy System
Li-ion Battery with LED
and 3-Stud or V-Mount
SAFETY INSTRUCTIONS
Make sure the battery is fully charged before use.
When not in use, remove the battery from its device. Some
electronic equipment will draw current even when the switch is off.
Do not short-circuit the terminals. This battery is protected with
an internal self-resetting fuse, but short circuits may still cause
severe damage to the battery.
Do not attempt to open the battery case under any circumstances.
Do not remove the battery from any equipment that is powered on.
Always power off your equipment before removing the battery.
Use the battery under proper environmental conditions: 14°F to
122°F (-10°C to 50°C) with a Relative Humidity (RH) less than 85%.
The battery may be warm during use or recharging. This is normal.
The battery should be charged up to 40% for storage longer than
one month, and should be charged every 6 months.
Keep the battery away from fire, heat, and high pressure.
Do not expose the battery to rain or moisture.
Do not drop the battery or subject it to strong shocks.
Keep this unit away from water and any flammable gases or liquids.
Clean the battery and terminals with only a clean, soft,
and dry cloth.
When operation time has noticeably decreased, the battery may
need to be replaced.
Keep this product away from children.
Store the battery in a cool, dry place.
5
6
OVERVIEW
. Battery-level check button
. Battery-level LED meter
Shows remaining capacity of
the battery. When capacity
reaches less than 9%, the
bottom LED will flash.
Slide lock
. D-tap output
12 V, 10 A max
. USB output
Press the battery-level check
button to start charging or to
power your USB device.
1. Mounting interface: 3-stud
or V-mount
1
2
3
4
5
6
4
2
3
1
IMPORTANT
You must connect both halves
of the buddy system battery in
order for it to be operational.
You can only connect the
halves of buddy system
batteries with matching
serial numbers.
After assembling the two
halves, the 100% battery
level LED will light up for
three seconds. Then, the
battery level will display the
current charge amount.
Product specificaties
| Merk: | Watson |
| Categorie: | Accu's camera |
| Model: | AM-192-B |
Heb je hulp nodig?
Als je hulp nodig hebt met Watson AM-192-B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Accu's camera Watson
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
17 Januari 2024
Handleiding Accu's camera
- Accu's camera Sony
- Accu's camera Dorr
- Accu's camera Eufy
- Accu's camera GoPro
- Accu's camera Nissin
- Accu's camera SeaLife
- Accu's camera Hähnel
- Accu's camera Anton/Bauer
- Accu's camera BlueShape
- Accu's camera Hedbox
- Accu's camera SWIT
Nieuwste handleidingen voor Accu's camera
13 September 2023
13 September 2023
6 September 2023
6 September 2023
6 September 2023
6 September 2023
6 September 2023
6 September 2023
6 September 2023
6 September 2023