Waring Commercial MX1200XTS Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Waring Commercial MX1200XTS (27 pagina's) in de categorie Blenders. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/27
Hi-Power Blender
Licuadora de alta potencia
Mélangeur/Bol mixeur à haute puissance
MX1200XTX/MX1200XTP/MX1200XTS
OPERATING MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D'UTILISATION
2 3
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed including the following:
1. READ ALL INSTRUCTIONS.
2. To protect against risk of electrical shock, do not put appliance in
water or other liquid.
3. Always unplug from outlet prior to handling or cleaning.
4. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
5. Unplug from outlet when not in use, before putting on or taking off
parts, and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions or is dropped or damaged in any
manner. Return appliance to the nearest authorized service facility
for examination, repair, or electrical or mechanical adjustment.
8. The use of attachments, including canning jars, not recommended
by the appliance manufacturer may cause hazards.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
11. Keep hands and utensils out of container while blending, to prevent
the possibility of severe personal injury and/or damage to the
blender. A rubber scraper may be used, but must be used only
when the blender is not running.
12. CAUTION: Blades are sharp. Handle carefully.
13. Always operate blender with lid in place.
14. When blending hot liquids, remove center piece of two-piece cover.
See hot blending instructions, page 5.
15. The use of ear protection is recommended during extended
operating periods.
16. Do not leave blender unattended while it is running.
17. See cleaning and sanitizing instructions, pages 6-8.
NOT FOR WATERJET CLEANING.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
• For your protection, this appliance is equipped with a 3-conductor cord set.
• 120 Volt units are supplied with a molded 3-prong grounding-type plug
(NEMA 5-15P) and should be used in combination with a properly connected
grounding-type outlet as shown in Figure A.
If a grounding-type outlet is not available, an adapter, as shown in Figure B,
may be used to enable a 2-slot wall outlet to be used with a 3-prong plug.*
As shown in Figure C, the adapter must be grounded by attaching its
grounding lug under the screw of the outlet cover plate.
Caution: Before using an adapter, it must be determined that the outlet
cover plate screw is properly grounded. If in doubt, consult a licensed
electrician.
Never use an adapter unless you are sure it is properly grounded.
*NOTE: Use of an adapter is not permitted in Canada and Europe.
Green/Yellow: Earth Ground. Blue: Neutral. Brown: Live.
NOTE: User-installed cord set plugs are not permitted in Europe.
MX1200XTX/MX1200XTP/MX1200XTS
BLENDER SPECIFICATIONS
• Capacity: 64 oz. Working Capacity
(48 oz. capacity – MX1200XTP)
• Switch Settings: (speeds) Variable Pulse
• Speed (RPMs) 1,500–20,000 30,000
• Rating: 120 Volts - 13.0 Amps
• Base Material: Polycarbonate
• Bearing: High Precision Ball Bearing
• Cord: 6-Foot Three-Conductor Ground Cord with Strain Relief in Base
• Overall Height: 19 Inches
• Weight: 15 lbs
• CETLUS, NSF listed
• Operating Cycle: 1 min. O /3 min. OFFN
4 5
MX1200XTX/MX1200XTP/MX1200XTS OPERATION
1. Before starting, make sure that the blender is unplugged.
2. With the unit in Off position, place container on blender base. Be sure
container is fully seated and that drive coupling is properly engaged.
Plug blender cord into outlet.
3. Put ingredients into container and cover it. Do not fill above MAX line.
4. This blender has variable speed controls. Set blender to desired speed
between 1 and 10.
5. The left paddle switch defaults to the VARIABLE setting in order to use
the speed adjustment option. Press right paddle switch up to the ON
position.
6. When finished blending, set paddle
switch to Off position.
7. This blender is equipped with a
pulse option. Hold left paddle switch
in down position to engage pulse
function. Unit will run on max speed
(30,000 RPMs) until the paddle switch
is released.
8. Allow motor to come to a complete
stop before removing container
from blender base. Never place
the container on the motor base or
remove it from the motor base while
motor is running.
9. Always hold container with one hand when starting and while blending.
Never operate without jar lid.
10. Wash and dry container after each use. See cleaning and sanitizing
instructions, pages 5-7.
RESETTING THERMAL PROTECTION
• Your blender is equipped with an automatic reset function to protect
the motor from overheating.
• If your blender stops running under heavy use, turn the power switch
Off and unplug the power cord. Empty the blender container of all
its contents and allow between 5 to 30 minutes for the motor to
cool down.
• Plug the power cord back into the outlet and continue blending.
• If your blender does not function properly following this procedure,
discontinue use and contact a certified Waring Customer Service Center.
IMPORTANT
HOT BLENDING INSTRUCTIONS
To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.
• Hot materials are those that are 100 F (38 C) or hotter.° °
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece container lid
before starting motor (this will allow venting of the rapidly heated and
expanding air inside the container when blender is running).
• Always start blending on lowest speed setting, and then progress to
desired speed.
• Never stand directly over blender when it is being started or while it
is running.
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE
OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL
TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY,
RENDERING THEM INEFFECTIVE.
• Wash, rinse, sanitize and dry container prior to initial use and whenever it
will not be used again within a period of 1 hour.
• Wash and rinse container after each use.
• Clean and sanitize motor base prior to initial use and after each use.
• Washing solutions based on non-sudsing detergents and chlorine-based
sanitizing solutions having a minimum chlorine concentration of 100 PPM
are recommended.
The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.
SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
Washing Diversey Wyandotte 4 tablespoons Hot 115ËšF (46ËšC)
Diversol BX/a or CX/A /gallon
Rinsing Plain Water Warm 95ËšF (35ËšC)
Sanitizing Clorox® 1 tablespoon/gallon Cold 50-70˚F
Institutional Bleach (10-21ËšC)
• In repetitive batch-processing applications, frequent cleaning of the
container will prolong the life of the blade assembly. In no case should
actual running time between cleanings exceed one-half hour.
• Do not use container to store processed foods or beverages.


Product specificaties

Merk: Waring Commercial
Categorie: Blenders
Model: MX1200XTS

Heb je hulp nodig?

Als je hulp nodig hebt met Waring Commercial MX1200XTS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Blenders Waring Commercial

Handleiding Blenders

Nieuwste handleidingen voor Blenders