Vimar 01986.120 Handleiding

Bekijk gratis de handleiding van Vimar 01986.120 (1 pagina’s), behorend tot de categorie Dimmer. Deze gids werd als nuttig beoordeeld door 39 mensen en kreeg gemiddeld 4.9 sterren uit 9 reviews. Heb je een vraag over Vimar 01986.120 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Viale Vicenza, 14 - 36063 Marostica VI Italy

Tel. +39 0424 488 600 - Fax (Italia) +39 0424 488 188 - Fax (Export) +39 0424 488 709

www.vimar.com

SLAVE dimmer 120 V~ 60 Hz for incandescent lamps 40-500 W electronic

transformers 40-300 VA, CFL lamps 10-200 W, LED lamps 3-200 W, control from

universal MASTER dimmer with load adapter, protection fuse, installation on

DIN rails (60715 TH35), occupies 4 modules size 17.5 mm. For nautical scope.

MOSFET+TRIAC microprocessor technology, works in both LE (Leading Edge) and TE (Trailing

Edge) modes, equipped with protection fuse, can be installed on DIN rails (60715 TH35). It does

not require connecting to the busbar, but the sync signal from a MASTER dimmer for DIN rails

01985.120. No buzzing whatsoever.

IMPORTANT: Lamps controllable from a single master or slave dimmer must all be the same.

All controllable loads must be declared DIMMERABLE by the manufacturer. Check the type

of compatible dimmering on the lamp package: LE (Leading Edge) or TE (Trailing Edge). If it is

not specified, the lamp can operate in both modes (chosen at the discretion of the installer).

CHARACTERISTICS.

• Ratedsupplyvoltagemains:120V~,60Hz

• Dissipatedpower:7.4W

• Terminals:Nneutral, load, phase, synchronizationL S

• ProtectionfusetypeF5AH250V

• SLAVEdimmersneedasynchronismsignaltofunction

• Softstart: ensuresgraduallightingfrom zeroto maximum orpresetlightinglevels. Thisway

the life of a lamp is increased by reducing stress on the filament and prevents light flash.

• Flashstart: used with compact fluorescentlamps, ensures that the lamps areswitched on

correctly, reducing any difficulties to a minimum.

• Softend:slowlybringstheloaddownfromontooff.

• Lightinglevelissavedwhenturnedoff(unlessthereisablackout);

• LeadingEdge mode:  usedwith incandescent lamps, compact fluorescentlampsand LED

compatible lamps, as well as

L

type electronic transformers.

• TrailingEdge mode: usedwith compatible loadssuchas fluorescentlamps,LEDlamps or

C

type electronic transformers.

• Protectionagainstshort-circuitingwhenturningonwithflashingblow-outindicator.

• Thermalprotectionwithflashingblow-outindicator.

• InstallationonDIN rails (60715 TH35) , occupies 4 modules of 17.5 mm.

CONFIGURATION.

WARNING: When connecting MASTER-SLAVE, the SLAVE must be configured (using the

dip-switches) in the same operating mode as the MASTER.

The dimmer 01986.120 can be configured by the two dip switches which are accessible from

thefront:

INSTALLATION RULES.

Installation should be carried out in compliance with the current regulations regarding the instal-

lation of electrical systems in the country where the products are installed.

• Itshouldbeusedinplacesatatemperatureofbetween-5°Cand+45°C.

• Thelampsconnectedtothemasterorslavemustallbethesame.

• Notsuitableforcontrollingmotors(e.g.fans,ventilators).

•Theratedpowerlevelshouldneverbeexceeded.

Controllable loadsLETE

40 to 500 W40 to 300 W

10 to 100 W10 to 200 W(Max 5 lamps) (Max 10 lamps)

3 to 100 W3 to 200 W(Max 5 lamps) (Max 10 lamps)

Electronic transformers

for halogen lamps

40 to 300 W

(Max 3 transformers type

L

)

40 to 300 W

(Max 5 transformers type

C

)

Dimmering with Leading Edge mode Dimmering with Trailing Edge mode

• Overloading, power surges and short-circuits may irreparably damage dimmers. Before

installation check the circuit carefully and eliminate any of the above causes.

• The dimmer doesnot have a mechanicalcircuitbreaker inthe main circuit and so isnot

galvanically separated. The circuit load should be considered always powered.

For further instructions see the manual enclosed with the control panel.

CONFORMITY TO STANDARDS.

For MARINE use,thisdevicehasbeensubmittedtothefollowingtests:

IEC60068-2-52-TestKb:Saltmist,cyclic(sodium,chloridesolution),

IEC60068-2-6-TestFc:Vibration(sinusoidal)

This device complies with part 15 of the FCCRules(withthelimitsforaClassBdigitaldevice).

Operation is subject to the following two conditions:(1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference

that may cause undesidered operation.

FRONT VIEW

CONNECTIONS

MaximumlengthofcablesconnectinguniversalMASTERdimmeranduniversalSLAVEdimmer:100m

Connect at least the minimum load required to the universal master dimmer.

A:IndicatorLED

B:Dipswitch

CHANGING FUSE

OFF

1.

Setting

onto TE

Setting

onto LE

Setting onto Flash

instant lighting on maximum

brightness and then it adjusts

linearly to the set brightness

Setting onto Soft

gradual lighting up to the set

brightness

TE

LE

TE

LE

Flash

Soft

Flash

Soft

A

LN

S

NL S

TE Flash

Soft

LE

01986.120

SLAVE

DIMMER

40-500W LE

40-300W TE

120 V~ 60 Hz

B

NLS

NLS

01986.120

SLAVE

TE Fla sh

S oft

LE

DIMMER

120V~

60Hz

40-5 00W LE

40-300 W TE

By-me

NLS

2.

01986.120

01986.12001985.120 01986.120

NL S

TE Flash

Soft

LE

01986.120

SLAVE

DIMMER

40-500W LE

40-300W TE

120 V~ 60 Hz

NL S

TE Flash

Soft

LE

01986.120

SLAVE

DIMMER

40-500W LE

40-300W TE

120 V~ 60 Hz

NL S

01985.120

MASTER DIMMER

120 V~ 60 Hz

40-500W LE

40-300W TE

L

N

Bus

MASTER SLAVESLAVE

49400503A0 01 1309

VIMAR - Marostica - Italy

Product specificaties