Vemer PR-1P7A Handleiding

Vemer Niet gecategoriseerd PR-1P7A

Lees hieronder de 📖 handleiding in het Nederlandse voor Vemer PR-1P7A (26 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/26

- 27 -

User Manual Regulators

English

Contents

■Safety warnings Page 28

■Technical specifications Page 28

■Description of instrument Page 31

■Electrical connections Page 31

■Glossary Page 32

■Operation Page 37

■Setting the regulation parameters Page 37

■Parameter menu Page 39

■Error messages Page 46

■Reference standards Page 47

■Dimensions and connection diagrams, 33x75 mm Page 48-49

■Dimensions and connection diagrams, 72x72 mm Page 50

■Dimensions and connection diagrams, 4-DIN Page 51

- 28 -

User Manual Regulators

English

■ During the installation and operation of the instrument, follow the

instructions set out below:

1) The instrument should be installed by a skilled operator.

2) Strictly follow the connection diagrams when installing the instrument.

3) Do not power or connect the instrument if any part of it is damaged.

4) Before touching the terminals, make sure the wires to be connected to

the instrument are not live.

5) The connection cables should be able to resist the maximum operating

temperature (Tmax), obtained from the sum of the maximum ambient

temperature (Ta) + a temperature of 20 °C (Tmax= Ta + 20 °C).

6) The instruments guarantee a main insulation between the low voltage

(250 V) and very low voltage parts.

7) Any outside switches connected to the controls should guarantee a

minimum insulation at operating temperature of 250 V AC, or should be

protected by equivalent insulation.

8) Contacts: all type 1C (CEI 107-70 and variants).

9) The instruments require no maintenance.

■Series of digital regulators used for the most simple requirements in the control

and regulation of humidity and pressure levels in air conditioning, heating

and refrigeration systems

■Two dedicated base models for pressure and humidity control:

- DIGITAL HUMIDITY REGULATORS HR

- DIGITAL PRESSURE REGULATORS PR

■Each single model has 1 probe input for the connection of active sensors

with standardised 0÷20 mA, 4÷20 mA and 0÷1 V outputs

■The power supply to the active probe (linear sensor) comes directly from

the instrument: 9 V DC available

• For each single model, the probe input can be configured from the keyboard

• Available in versions with 1 or 2 relay outputs with contact in exchange

• Regulators with 3 digit, seven segment and decimal point display

• Relay intervention warning lamp

• Display range: -99 ÷ +999

• Display resolution: 0.1 RH or bar (-9.9 ÷ +99.9 RH or bar)

and 1 RH or bar (< -9.9 °C and > +99.9 RH or bar)

• Precision: ±0.5 % of the end of scale value ±1 digit

(at an ambient temperature of 23 °C)

• Sampling time: 0.5s

TECHNICAL SPECIFICATIONS

SAFETY WARNINGS

- 29 -

User Manual Regulators

English

• Parameter setting in digital mode:

- Set point

- Differential

- Neutral zone

- Output drive timing

- Digital input delay function and time

- Alarm delay / buzzer enable time

- Probe calibration offset

- Resolution displayed

- Measurement display filter (update speed)

- Type of probe input

- Password

- Operating modes (regulation):

— ON/OFF Direct and/or Reverse action with or without neutral zone

— PWM Direct and Reverse action with or without neutral zone

— ALARM

— Special mode

• 2 independent set points

• Digital input: 1 (not versions HR-..P7A, PR-..P7A) for outside consensus

for configurable function: outside alarm, regulator ON/OFF, set-point switching,

Direct/Reverce switching, etc.

Acoustic and visual alarm signalling for: outside alarm (from digital input),

probe alarm (malfunction), minimum or maximum alarm

• Infrared receiver with RC-5 protocol for remote control (accessory available

separately for remote programming)

• Available in the following fixing versions: 33x75 mm rear panel, 72x72 mm

rear panel and modular 4 DIN

• Power supply: see table on the following page

• Rated power: 3 VA for models with 33x75 mm rear panel fixing

4.5 VA for models with 72x72 mm and modular 4 DIN fixing

• Max absorption: 100 mA at 12 V - 50 mA at 24 V (1 channel)

• Operating temperature: 0 ÷ +50 °C

• Operating humidity: <80%

• Storage temperature: -10 ÷ +70 °C (<80% RH)

• Protection level: front panel IP54 (IP40 for the 4 DIN module version)

terminals IP20

Product specificaties

Merk:	Vemer
Categorie:	Niet gecategoriseerd
Model:	PR-1P7A

Heb je hulp nodig?

Als je hulp nodig hebt met Vemer PR-1P7A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Vemer

Vemer Elettrosonda Z Handleiding

5 September 2023

Vemer Memo NFC Handleiding

17 Juni 2023

Vemer Orion Handleiding

17 Juni 2023

Vemer FHT-2DA Handleiding

12 Juni 2023

Vemer HT NTC-1P3D Handleiding

5 Juni 2023

Vemer HR-1P7A Handleiding

2 Juni 2023

Vemer VE LAN Handleiding

31 Mei 2023

Vemer LCR048 Handleiding

29 Mei 2023

Vemer CH4 Sensor Handleiding

24 Mei 2023

Vemer PSR400 Handleiding

22 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024