Vemer CH4 Sensor Handleiding

Vemer Niet gecategoriseerd CH4 Sensor

Bekijk gratis de handleiding van Vemer CH4 Sensor (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 208 mensen en kreeg gemiddeld 4.7 sterren uit 104.5 reviews. Heb je een vraag over Vemer CH4 Sensor of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF
Pagina 1/1
V3IS00462-010
CH4 Sensor CO Sensor LPG Sensor, and areprobesforthedetectionof
methanegas,carbonmonoxideandLPGtobeconnectedtoSRG and SRG.4
controlunitstocreatesystemsfordetectinggasinareassuchasboilerrooms,
warehouses,etc.
It is wall-mounted in a vertical position using screws and plastic plugs.
SAFETY WARNINGS
During installation and operation of the instrument, comply with the
following instructions:
1) The device must be installed by a competent person
2) Before removing the cover, make sure that power is NOT provided to
the device
3) Before accessing the terminals, make sure that the electrical leads are
not live
4) Install the detector in the correct position (see “Installation”)
5) Do not power on the device if any part of it is damaged
Code Model Description
VE205100 CH4SENSOR Methanedetectionsensor
VE206900 LPG SENSOR LPG sensor
VE207700 CO SENSOR Carbonmonoxidesensor
TECHNICAL CHARACTERISTICS
• Powersupply:fromthecontrolunitSRGorSRG.4
 −Currentinput(at6.5V):40mA
 −Connection:terminalsof2.5mm2C(common),S(signal),A(powersupply)
• Modelsandcalibration:
 −Methanegas:CH4Sensor,(default)10%LIEofmethane
 −LPG:LPGSensor,(default)12%LIEofisobutene
 −Carbonmonoxide:COSensor,(default)200ppmofcarbonmonoxide
• Max.lengthofconnection:50m
• Container:inself-extinguishingplasticmaterial
• Fastenedtowallusingscrewsandplasticplugs
• Protection:IP30
• Operatingtemperature:0÷+50°C
• Humidity: 90%R.H.withoutcondensation≤
INSTALLATION
 LPG,COandCH4Sensorsaredesignedtobewall-mounted(vertically),using
screwsandplasticplugs.Toproceedwithinstallation,openthecontainerby
unscrewingthescrewlocatedonthelowerside.Makesurenottodamagethe
sensorandnottotouchthecalibrationdevices.
POSITIONING
 Thecorrectinstallationoftheprobeisessentialtoproperoperationofthe
system.Therefore,itmustbeinstalled:
• Inareaswithcirculationofnaturalair;
• Inareasthatarenotsubjecttodustordirtthatmayrenderthesensor
inoperative;
• Nearjetsofwater,intakegrilles,openings,etc.
• Atanadequatedistancefromusersofgassoastopreventthesystemfrom
interveningimproperlyduetofunctionalleakage.
 Also,positioningdependsonthetypeofgastobedetected,specically:
• CH4 Sensor: Methane gas – at top, about 20-30 cm from the ceiling
• LPG Sensor: LPG – at bottom, about 20-30 cm from the floor
• CO Sensor: carbon monoxide – about 1.5 m from the floor
 Fornewsystems,theprobemustbeinstalledaslateaspossible,sothattypical
constructionsiteactivitiesdonotdamagethedetector.
CONNECTIONS
 Normalelectricalcablescanbeusedforconnections.Inanycase,when
installationisinplacesthatarestronglyexposedtoelectromagnetic
disturbances,itisadvisabletouseshieldedcables.Thedetectionsystemmust
alwaysbeinoperation.Therefore,theelectricalpowersupplyofthedetector
mustnotincludeswitchesorotherdevicesthatmayaccidentallyshutitoff.The
averagelifespanoftheprobesis5yearsfromthedateofinstallation.Therefore,
attheendofthattimetheywillneedtobereplaced.
Note. Make sure you check operation at least once a year, and in any
case whenever there is an extended period of disuse or in the event of
replacement. Any tampering may compromise correct operation of the
system.
REFERENCE STANDARDS
CompliancewithCommunityDirectives:
2006/95/EC (lowvoltage)
89/336/EECmod.from andfrom92/31/EEC 93/68/EEC(E.M.C.)
isdeclaredwithreferencetothefollowingstandards:
EN 61779-4, EN 50270
User Manual
SENSORS FOR SRG/SRG.4 CONTROL UNITS
Read all the instructions carefully
Dimensions
Connection diagrams
119,0
75,3
75,3
36,0
CH4 SENSOR
C S A
C S A
SRG/SRG.4
Mod. CH4 SENSOR
Mod. LPG SENSOR
Mod. CO SENSOR

Product specificaties

Merk: Vemer
Categorie: Niet gecategoriseerd
Model: CH4 Sensor

Heb je hulp nodig?

Als je hulp nodig hebt met Vemer CH4 Sensor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Vemer

Vemer

Vemer Elettrosonda Z Handleiding

5 September 2023
Vemer

Vemer Memo NFC Handleiding

17 Juni 2023
Vemer

Vemer Orion Handleiding

17 Juni 2023
Vemer

Vemer FHT-2DA Handleiding

12 Juni 2023
Vemer

Vemer HT NTC-1P3D Handleiding

5 Juni 2023
Vemer

Vemer HR-1P7A Handleiding

2 Juni 2023
Vemer

Vemer VE LAN Handleiding

31 Mei 2023
Vemer

Vemer LCR048 Handleiding

29 Mei 2023
Vemer

Vemer CH4 Sensor Handleiding

24 Mei 2023
Vemer

Vemer PSR400 Handleiding

22 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Berkel

Berkel Suprema Macelleria PEM350 Handleiding

17 Juni 2025
Silvercrest

Silvercrest SGRS 3.6 A1 Handleiding

17 Juni 2025
Fiamma

Fiamma Fixing-Bar Pro L Handleiding

17 Juni 2025
Chapin

Chapin 31410 Handleiding

17 Juni 2025
Parkside

Parkside PPL 10 A2 Handleiding

17 Juni 2025
Parkside

Parkside PSTD 800 E4 Handleiding

17 Juni 2025
V-Tac

V-Tac VT-10000 Handleiding

17 Juni 2025
Rane

Rane DC 24 Handleiding

17 Juni 2025
Hoshizaki

Hoshizaki KMS-822MLJ Handleiding

17 Juni 2025
Fiamma

Fiamma F80s Handleiding

17 Juni 2025