Uline H-3255 Handleiding


Pagina's 6 Kast

Bekijk de handleiding van Uline H-3255 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag

PAGE 1 OF 6 0325 IH-1060
WIDE SPAN/LAMINATE
STORAGE RACKS
1-800-295-5510
uline.com
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
PARTS
ASSEMBLY
with another person.
1. Connect two upright posts (A) by inserting a side
support piece (B) at the bottom and top of the posts.
(See Figure 1)
NOTE: Side supports should be positioned with
ledge on top.
2. Repeat step one for the other two upright posts (A).
Upright Post x 4 (A)
Shelf Support x 3 (D)Side Support x 6 (B)
Front/Back Support x 6 (C)
NOTE: 72" wide racks utilize two shelf supports per level
(total of six per shelving unit).
NOTE: 96" wide racks utilize three shelf supports per
level (total of nine per shelving unit).
Figure 1
B
A
B
NOTE: 96 x 36" and 96 x 48"
(W x D) shelves utilize two
laminate boards per level
(total of six per shelving unit).
NOTE: 96 x 36" and 96 x 48"
(W x D) shelves utilize two
particle boards per level
(total of six per shelving unit).
NOTE: 96" wide shelves utilize
two wire decks per level (total
of six per shelving unit).
Shelving Material Options
Laminate Board x 3 (E)
Particle Board x 3 (E)
Wire Decking x 3 (E)
Rubber Mallet
TOOL NEEDED
Two Person Assembly
Recommended
PAGE 2 OF 6 0325 IH-1060
ASSEMBLY CONTINUED
Figure 3
C
Figure 4
D
Figure 5
E
E
Figure 2
B
A
1
-800-295-551
0
une.comli
3. Place side support pieces (B) in the middle of the
upright posts at desired middle shelf height.
(See Figure 2)
4. Connect the two upright post assemblies by inserting
front/back supports (C) at the top and bottom of
each upright post. (See Figure 3)
NOTE: Be sure the supports are fully seated
before continuing with assembly.
NOTE: Front/back supports should be positioned
with ledge on top.
5. Repeat step 4 for installation of all other front/back
supports.
6. Attach shelf supports (D) at each level by placing the
keyhole slots (on shelf support) over the rivets (on the
inside of the front/back support) and tapping them
into place. (See Figure 4)
Recommended number of shelf supports per shelf are as
follows:
36" / 48" / 60" − 1 Shelf Support
72" − 2 Shelf Supports
96" − 3 Shelf Supports
7. Set boards or wire (E) on top of shelf supports, side
supports, and front/back supports. (See Figure 5)
PAGE 3 OF 6 0325 IH-1060
RACKS AMPLIOS PARA
ALMACENAMIENTO CON
REPISAS LAMINADAS
800-295-5510
uline.mx
NOTA: Apoye los postes contra una pared o
ensamble con la ayuda de otra persona.
1. Conecte dos postes verticales (A) insertando una
pieza de soporte lateral (B) en la parte inferior y
superior de los postes. (Vea Diagrama 1)
NOTA: Los soportes laterales deben
colocarse con el reborde hacia arriba.
2. Repita el paso uno para los otros dos
postes verticales (A).
Diagrama 1
B
A
B
NOTA: Los racks amplios de 72" utilizan dos soportes para
repisa por nivel (un total de seis por unidad de estantería).
NOTA: Los racks amplios de 96" utilizan tres soportes
para repisa por nivel (un total de nueve por unidad de
estantería).
PARTES
ENSAMBLE
NOTA: Las repisas de 96 x 36" y
de 96 x 48" (Ancho x Profundidad)
utilizan dos tablas laminadas por
nivel (un total de seis por unidad
de estantería).
NOTA: Las repisas de 96 x 36" y
de 96 x 48" (Ancho x Profundidad)
utilizan dos tablas de aglomerado
por nivel (un total de seis por
unidad de estantería).
NOTA: Las repisas de 96" de ancho
utilizan dos repisas de alambre por
nivel (un total de seis por unidad de
estantería).
Opciones de Materiales para Estantería
Mazo de Caucho
HERRAMIENTA NECESARIA
4 Postes Verticales (A)
3 Soportes de Repisa (D)6 Soportes Laterales (B)
6 Soportes Frontales
y Posteriores (C)
3 Repisas Laminadas (E)
3 Tablas de Aglomerado (E)
3 Repisas de Alambre (E)

Beoordeel deze handleiding


Product specificaties

Merk: Uline
Categorie: Kast
Model: H-3255

Heb je hulp nodig?

Als je hulp nodig hebt met Uline H-3255 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden