Uline H-11957 Handleiding
Pagina's 14 Waterpomp
Bekijk de handleiding van Uline H-11957 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
PAGE 1 OF 14 0325 IH-11957
H-11957, H-11958
1/4 HP SUBMERSIBLE UTILITY
PUMP – AUTOMATIC
1-800-295-5510
uline.com
Carefully read, understand and follow all safety
instructions.
Read these warnings carefully. Know the application
and limitations of this pump. Failure to follow these
warnings could result in serious bodily injury and/or
property damage.
DANGER! Risk of electric shock. Disconnect
and lock out power supply before removing
old pump or installing or servicing this pump.
DANGER! Risk of electric shock. This pump
is supplied with a grounding conductor
and grounding type attachment plug. To
reduce the risk of electric shock, ensure
that it is connected only to a properly
grounded, grounding type receptacle. For
added safety, it is highly recommended to
connect this pump to a GFCI (Ground Fault
Circuit Interrupter) outlet. Connect only to a
receptable that is adequately rated for the
voltage and amperage of this pump
WARNING! The installation of this pump must
be in accordance with the National Electric
Code (NEC), Uniform Plumbing Code (UPC),
International Plumbing Code (IPC) as well as all
applicable local codes and ordinances.
CAUTION! Do not install this pump in any
location classified as hazardous by the
National Electric Code, ANSI/NFPA70.
CAUTION! Do not use this pump to pump
flammable or explosive fluids such as gasoline,
kerosene, etc. Do not use this pump in
flammable or explosive environments. Use only
with liquids compatible with pump component
materials.
WARNING! Risk of electric shock. This pump has
not been investigated for use in swimming pool
or marine areas.
WARNING! Risk of electric shock. Do not use the
power cord to install or carry the pump. Always
use the handle. The cord may pull apart,
exposing bare wires which could cause a fire
or electric shock. Use the handle supplied with
the pump for installing and transporting the
pump.
WARNING! Do not run pump dry. This pump
relies on water for cooling. Running the pump
dry can cause the pump to overheat and the
possibility of burns to anyone that handles
the pump. Running the pump dry will void the
warranty.
WARNING! Do not use this pump for
potable/drinking water. Use only in applications
for which the pump is designed.
WARNING! Ensure that the electric outlet is
within the reach of the power supply cord. Do
not use an extension cord. Extension cords
that are too long or too light do not deliver
sufficient voltage to the pump motor. More
importantly, they present a safety hazard if the
insulation were to become damaged or the
connection end were to fall into the water.
CAUTION! This pump motor is equipped with
an automatic resetting thermal protector and
may restart unexpectedly.
SAFETY
Para Español, vea páginas 5-9.
Pour le français, consulter les pages 10-14.
PAGE 2 OF 14 0325 IH-11957
DESCRIPTION
This automatic submersible utility pump is designed to remove water from flooded basements, window wells and stock
tanks, etc. The permanent split capacitor motor is oil-filled and hermetically sealed for cooler operation. The pump
comes equipped with a three-prong grounding type power cord.
SPECIFICATIONS
MODELH-11957H-11958
Motor TypePermanent Split Capacitor (PSC)
Motor ProtectionAuto Reset Thermal Overload Protector
Discharge Size1" MNPT and 3/4" GHT (Adapter Included)
HP1/41/4
Volts115115
Amps3.53.5
Hz6060
PhaseSingleSingle
Motor Operation3,450 RPM3,450 RPM
Maximum Solids Handling1/8"1/8"
Liquid Temperature Range32°–104°F32°–104°F
Cord Length10'25'
Pump HousingThermoplasticThermoplastic
Pump BaseThermoplasticThermoplastic
Impeller MaterialThermoplasticThermoplastic
FastenersStainless SteelStainless Steel
Maximum PSI8.58.5
*For continuous operation, the water depth must be at least 6" to prevent the
motor from overheating.
WARNING! Do not under any circumstances
remove the ground pin. The three-prong plug
must be inserted into a matching
three-prong grounded receptacle. If the
installation does not have such a receptacle,
it must be changed to the proper type,
wired and grounded in accordance with
the National Electric Code (NEC) and all
applicable local codes and ordinances.
WARNING! All wiring must be performed by a
qualified electrician.
WARNING! Keep hands clear of suction and
discharge openings. To prevent injury, never
insert fingers into pump while it is plugged in.
WARNING! Do not handle this pump with wet
hands or while standing on wet or damp
surfaces or in water.
TECHNICAL DATA
SAFETY CONTINUED
PAGE 3 OF 14 0325 IH-11957
OPERATION
• Connect the plug into a 115 V AC grounded outlet.
The use of a GFCI is strongly recommended.
• The pump will turn on once the water level reaches
approximately 1⁄". The water level must be high
enough to activate the switch located on the side of
the pump. (See Figure 1)
• The pump will remove water down to approximately
1/8" of the surface. Once the water reaches that
level, the pump will run for approximately 45
seconds and then turn off. It is normal for the pump
to operate in this situation even though no water
may be flowing.
• The pump is automatic and can remain plugged in.
The pump will automatically turn on once the water
level reaches 1⁄" again.
CAUTION! Do not let the pump run dry. The
pump depends on water for cooling and
lubrication. Operating the pump without water
may cause the motor to overheat or cause
damage to internal parts. It may also shorten
the life of the pump.
CAUTION! The pump motor is thermally
protected. It is not recommended for pumping
liquids over 104°F. The thermal overload
protector will automatically shut down the
pump in an overheat/overload situation. The
pump will reset itself once it cools down. This
overload is designed as a safety device, and it
will fail after repeated use. Normal operation is
for fluids between 32°F–104°F.
PERFORMANCE
Height, pipe diameter restriction and hose length
will reduce the pump output performance. It is
recommended to use the same size or larger pipe/hose
as the pump discharge for optimum performance. The
performances listed below were obtained by using 1⁄"
pipe. The use of a garden hose will reduce the output
depending on size and length of hose used.
SETUP
UNPACKING
Upon receiving the pump, it should be inspected for
damage or missing parts.
INSTALLATION
There are two options for hose installation.
1. Attach a discharge hose to the 1" discharge using
an adapter (sold separately). Extend the hose,
ensuring there are no kinks or tight bends.
2. Thread the 3/4" garden hose adapter onto the pump
discharge. Attach a garden hose (sold separately)
to the garden hose adapter. Extend the hose,
ensuring there are no kinks or tight bends.
NOTE: To keep friction loss as low as possible,
hose must be 1/2" or larger inside diameter.
Use the shortest length of hose possible for the
application.
Figure 1
Activate 1⁄"
Turn Off 1/8"
Discharge Height0'5'10'15'20'
Gallons Per Minute3026221711
30
25
20
15
10
5
0
0
5101520
Gallons Per Minute
Discharge Height
2530
Product specificaties
| Merk: | Uline |
| Categorie: | Waterpomp |
| Model: | H-11957 |
Heb je hulp nodig?
Als je hulp nodig hebt met Uline H-11957 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden