Ugreen NASync DXP4800 Pro Handleiding
Pagina's 5 Niet gecategoriseerd
Bekijk de handleiding van Ugreen NASync DXP4800 Pro gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
Model: DXP4800 Pro
Buzzer
StatusBeeper
Beep once
Beep once
Beep 3 times
Beep every 3 seconds
Beep every 2 seconds
Power on
Reset network and password
System reset
Hard drive error
System error
Product Name
Model
Operating System
Processor
Max Turbo Frequency
Memory Type
Memory Capacity
System Storage
Storage Mode
Supported Drive
Network Attached Storage
DXP4800 Pro
UGOS Pro
Intel i3-1315U
4.5GHz
SODIMM DDR5
8 GB-96 GB (max memory size)
128 GB SSD
JBOD/Basic/RAID 0/RAID 1/RAID 5/RAID 6/RAID 10
4 SATA (6 Gbps), supports 2.5"/3.5" hard drive
2 M.2 NVMe 2280 SSDs, PCIe 4.0 x4,
theoretical transfer rate of up to 64 GT/s
1 HDMI port, supports resolutions up to 4K
1 2.5GbE port, supports 2.5 Gbps and
backward compatible
1 10GbE port, supports 10 Gbps and
backward compatible
1 SD 3.0 slot, theoretical transfer rate of up to
104 MB/s
19V/7.9A
Temperature: 0℃~40℃/32℉~104℉
Humidity: 10% to 85%
1 USB-C 3.2 Gen2 Port, theoretical
transfer rate of up to 10 Gbps
1 USB 3.2 Gen 2 port, theoretical transfer rate
of up to 10 Gbps
2 USB 2.0 ports, theoretical transfer rate of up
to 480 Mbps
1 USB 3.2 Gen 1 port, theoretical transfer rate
of up to 5 Gbps
Notices
· This product contains a built-in Lithium Manganese Dioxide battery.
Do not dismantle, crush, squeeze, or expose it to fire.
· Do not expose this product to excessive temperatures.
· Please keep this product out of reach from children.
· If the battery has been accidentally swallowed or placed inside
any part of the body, it may cause severe internal burns or other
hazards. Seek medical attention immediately.
· Do not charge the battery. If the battery is low, promptly replace
it. When replacing the battery, ensure the battery polarity is not
reversed.
· If battery leakage occurs, avoid contacting with skin or eyes. In
case of contact with skin or eyes, rinse with water and seek
medical attention immediately.
· Keep depleted batteries out of reach from children, and dispose of
or recycle it properly in accordance to local laws and regulations.
Ⅰ. Preparation
Package Contents
UGREEN NASync DXP4800 Pro
Product Overview
Indicator
LED
Power
indicator
Hard drive
indicator
LAN
network
indicator
White
Blinking
(once per 0.5 second)
Blinking
(once per second)
Blinking
(once per second)
Blinking
Pulsing
System hibernationPulsing
Device error
Error
Internet connected
Read/Write
Hibernation
Internet not connected
Data transfer
(Internet not connected)
On
Blinking
On
Blinking
White
Orange
Orange
White
Orange
ColorStatusDescription
Power on
Data transfer
(Internet connected)
On
HDMI Port
RJ45 Ethernet Port
KEEP OUT OF REACH
OF CHILDREN
WARNING
1×Quick
Start Guide
1×Warranty
Card
2×Tray
Key
1×Main
Unit
1×Power
Adapter
2×SSD
Thermal Pad
2×Ethernet
Cable (CAT7)
Screws and
Screwdriver
Power off
SD Card Slot
Power Input
Working
Environment
Product
Dimensions
USB Port
L257.5×W178×H178 (mm)
· Please place the NAS device as referred to in the illustrations in this
manual.
· Please put the NAS in an environment with a stable temperature and
low humidity. Avoid direct sunlight or any liquids coming into contact
with the device.
· In the event of a thunderstorm or inconsistent voltage, power off the
device to avoid potential damage.
· Keep the device away from heat sources or humid environments to
reduce the risk of fire or electric shock.
· Do not insert foreign objects into the NAS to avoid damage caused by
abnormal use or short circuit.
· Please power off the NAS device before cleaning. When cleaning, use
a moist wipe. Do not use chemicals or spray cleaners.
· Do not drop, squeeze, violently impact, or throw the NAS.
· This device contains small parts and pieces, please keep it out of
reach of children to prevent choking due to unintended swallowing.
· Do not dismantle or fix the NAS device by yourself. Improper
disassembly and assembly may cause electric shock or other safety
hazards. If needs to repair or replace parts and / or accessories,
please contact UGREEN NAS customer service.
Bottom View
Front View
Back View
Hardware Specification
Power Indicator
Hard Drive Indicator
SD Card Slot
Power Button
Network Indicator
USB-C 3.2 Gen2 Port
USB 3.2 Gen 2 Port
Safety Lock
Dust Filter
2×USB 2.0 Port
USB 3.2 Gen 1 Port
Reset Button
Power Port
10GbE Port
2.5GbE Port
HDMI Port
Panel (Unscrew to remove it)
QR Code (For binding device)
2×Memory Slot
(With one memory module pre-installed)
2×M.2 Slot (Optional)
Note:
· It is recommended to use new drives. When installing ANY drive(s), the
NAS system will format the drive, erasing ALL existing data. Ensure any
important data is backed up prior to installation.
· When setting up a "RAID mode", it is recommended to use hard drives
with the same capacity. This allows you to maximize storage capacity
utilization and reduces the risk of data loss.
At least one 3.5'' or 2.5''
SATA hard drive
Included SSD thermal pad
(required only for installing
M.2 drives)
Install 2.5'' Hard Drive
(Screwdriver Required)
1. Remove the pin: On the right side of the drive tray, remove the
pin at the end of the tray using the tray key. Safekeep this
pin by placing the pin into the hole on the other side.
2. Install the hard drive: Flip the tray to its back and align the four empty
screw spaces at the bottom of the hard drive with the screw holes on the
tray.
3. Secure the hard drive: Tighten the screws to fasten the hard drive to
the tray.
If you want to replace the 2.5-inch hard drive back with a 3.5-inch
one later on, please move the screw back to the tray end.
Pull out Hard Drive Tray
Insert the tray key into the lock hole and turn right. Press the button
below and pull out the tray.
Install 3.5'' Hard Drive
(No Screwdriver Required)
1. Flip the tray: Flip the hard drive tray back.
2. Open the clamp: Press the buckle marked with "Press" and gently
extend the clamp outwards.
3. Install the hard drive: Put the hard drive onto the tray.
4. Secure the hard drive: Push the clamp back, locking the hard drive
into place.
5. Put back the tray: Insert the tray loaded with hard drive back and
push it till the end. Press on the handle to secure the tray into
place. Lock the tray with the key by turning left.
Install M.2 SSDs
(Thermal Pad Sticking Required)
1. Power off the device and disconnect it from power supply. Turn
NAS over, unscrew and remove the bottom panel.
2. Loosen the SSD fixing screw.
3. Align the SSD connector with the slot, then insert the hard drive
into the slot at a slight angle. Tighten the screw.
4. Peel off the plastic film on the thermal pad, and then stick it to
the SSD.
5. Put back the panel and tighten the screws again. Power on the
device, after successful boot up, go to the "UGREEN NAS" app to set
the SSD cache.
Slot 1 specification: PCIe 4.0 x4
Slot 2 specification: PCIe 4.0 x4
Remove the pin on the tray endPlace the pin into the hole on
the other side
Remove the pin from the
hole near the head
Attach it from inside of the tray
Rotate it clockwise to lock it in place
Align with the screw holes
Before removing the M.2 SSDs, please go to the "UGREEN NAS"
app to remove the SSD cache. Otherwise, data loss may occur.
Warning
4. Put back the tray: Insert the tray loaded with hard drive back and
push it till the end.
Press on the handle to secure the tray into place. Lock the tray with
the key by turning left.
Hard drive pins
face down
Align pins with
screw holes
abc
ab
Download App
Option 1: Website
The UGOS Pro system is designed to help users manage and utilize
NAS services across multiple devices and operating systems. You
can access it through Web browsers, PCs (for Windows/Mac),
mobiles and tablets (for Android/iOS), as well as TVs (for Apple
TV/Android TV). You can download the corresponding app through
following options:
Go to the download page:
https://nas.ugreen.com/pages/app-download, select the
corresponding app to install.
Option 2: App Store
Search for and install "UGREEN NAS" from your phone's app store.
Currently, the "UGREEN NAS" app has been launched on multiple
platforms including App Store and Google Play.
Ⅲ. Software Installation
Option 3: Scan the QR Code
Use your phone/tablet camera to scan the QR code provided below
or the one on the device, then install the corresponding app based
on your device's system.
Scan to install
！ All images below are for reference only and may vary due to product
improvements. Please refer to the actual interface.
Start up Your NAS
1. Use an Ethernet cable to connect the NAS to a LAN port on the
router or the Ethernet switch.
2. Connect a power supply to the device using the power adapter.
3. Press the power button to turn it on. To turn off, press and hold
the button for about 5s.
Note:
· To ensure data transfer efficiency, it is recommended to use a router or
switch with 10-Gigabit LAN ports or higher and to connect the NAS using
the included Ethernet cable.
· After powering on, you can download "UGREEN NAS" then go to
"Control Panel" > "Hardware & Power" to check "Auto power-on when
power is supplied"
Only use the original power adapter or a safety-certified power
adapter that meets the device's power specifications to prevent
potential explosion hazards.
Warning
Firmware Update
ONLY update firmware with a stable power supply.
Do NOT disconnect the power supply during the update process.
Included power
adapter
LAN
9
Product specificaties
| Merk: | Ugreen |
| Categorie: | Niet gecategoriseerd |
| Model: | NASync DXP4800 Pro |
Heb je hulp nodig?
Als je hulp nodig hebt met Ugreen NASync DXP4800 Pro stel dan hieronder een vraag en andere gebruikers zullen je antwoorden