Truper LIBA-4X24N3 Handleiding

Truper Schuurmachine LIBA-4X24N3

Lees hieronder de 📖 handleiding in het Nederlandse voor Truper LIBA-4X24N3 (20 pagina's) in de categorie Schuurmachine. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20

Manual

Belt sander

LIBA-4X24N3

Model Code

LIBA-4X24N3

Applies for:

100370

Power Sanding belt

4”x 24”1 200 W

ENGLISH

ESPAÑOL

CAUTION Read this manual thoroughly

before using the tool.

Technical data

Power requirements

General power tool safety warnings

Safety warnings for belt sander

Parts

Start up

Maintenance

Authorized Service Centers

Warranty policy

LIBA-4X24N3

ENGLISH

CAUTION

Contents

Keep this manual for future references.

The illustrations in this manual are for reference

only. They might be different from the real tool.

To gain the best performance of

the tool, prolong the duty life,

make the Warranty valid if

necessary, and to avoid hazards

of fatal injuries please read and

understand this Manual before

using the tool.

IP Grade IP20

LIBA-4X24N3

100370

4” x 24”

Class II

60 Hz

Belt sander

16 AWG x 2C with insulating temperature of 221 °F

1200 W

Code

Description

Belt

Voltage

Frequency

9,4 A

Current

Power

50 minutes work per 20 minutes idle. Maximum 6 hours per day.

Duty cycle

Conductors

Insulating

Power cord grips used in this product: Type “Y”.

Build quality: Reinforced insulation.

Thermal insulation on motor winding: Class E.

127 V

Technical data

Power requirements

ENGLISH

Tools with double insulation and reinforced insulation are

equipped with a polarized plug (one prong is wider than the other). This plug will

only fit in the right way into a polarized outlet. If the plug cannot be introduced into

the outlet, reverse the plug. If it still doesn’t fit, call a qualified electrician to install

for you a polarized outlet. Do not alter the plug in any way. Both types of insulation

eliminate the need of both a grounded third power cord with three prongs or a

grounded power connection.

When using an extension cable, verify the gauge is enough for

the power that your product needs. A lower gauge cable will cause voltage drop in the line, resulting in power loss and

overheating. The following table shows the right size to use depending on cable’s length and the ampere capability

shown in the tool’s nameplate. When in doubt use the next higher gauge.

WARNING

from 0 A and up to 10 A

from 10 A and up to 13 A

from 13 A and up to 15 A

from 15 A and up to 20 A

18 AWG(*)

16 AWG

14 AWG

8 AWG

16 AWG

14 AWG

12 AWG

6 AWG

3 (one grounded)

from 6 ft to 49 ft | higher than 49 ft

Ampere

Capacity Number of

Conductors Extension gauge

* It is safe to use only if the extensions have a built-in artifact for over current protection.

AWG = American Wire Gauge. Reference: NMX-J-195-ANCE

WARNING

WARNING Avoid the risk of electric shock or severe injury. When the power cable gets damaged

it should only be replaced by the manufacturer or at a Authorized Service Center.

The build quality of the electric insulation is altered if spills or liquid gets into the tool while in use.

Do not expose to rain, liquids and/or dampness.

Before gaining access to the terminals all power sources should be disconnected.

WARNING When operating power tools outdoors, use a grounded

extension cable labeled “For Outdoors Use”. These extensions are specially designed for

operating outdoors and reduce the risk of electric shock.

500 m/min

Speed

Product specificaties

Merk:	Truper
Categorie:	Schuurmachine
Model:	LIBA-4X24N3
Kleur van het product:	Grijs
Gewicht:	6000 g
Breedte:	100 mm
Hoogte:	610 mm
Stroombron:	AC
Input vermogen:	1200 W
Meegeleverde stofzak:	Ja
Extra handgreep:	Ja
Type schuurmachine:	Schuurmachine
Stofafzuigingspoort:	Ja
AC-ingangsspanning:	127 V
AC-ingangsfrequentie:	60 Hz
Stationair toerental band (max):	500 m/min
Stroomsterkte:	9.4 A
Vergrendeling (uit) schakelaar:	Ja
Telescoopsteel:	Ja